Question about 2006 BMW Mini

1 Answer

The rear window water jet is not spraying water

How do I dismantle the jet/unit and clean any grit or blockage from the system. The system is charged with water and is trying to spray with very little water getting through

Posted by on

  • Roberta Smith
    Roberta Smith May 11, 2010

    you are filling the rear resevoir with water ?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,075 Answers

You dont have to dismantle anything.simply get a thin sowing needle and put the pointed end into the small hole in the middle of the spray jet keep trying until until it clears;the little ball jet will move; again useing the needle move the ball back to point at screen ,hope this solves your problem.adrian

Posted on Feb 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to re attach supply hose to back window in T & C 2007


if the washer pump is working for the rear then you will have to remove the rear door interior panel and check the hose for a blockage and check and clean out the spray nozzle for the rear window. sometimes they get plugged and need cleaning.

Sep 18, 2014 | Chrysler Town & Country Cars & Trucks

1 Answer

How to unblock rear window wiper water pipe on I10


Firstly have someone operate the rear washer while you listen for motor operation at the front wheel well of the car (same side as the washer fluid reservoir).
If you can't hear the motor, then the motor is likely faulty and requires replacement.
You can operate the front washers to locate where both motors are. (under the car, beside the wheel well.)


If the motor is working but no water is coming out, then remove the rear washer jet and disconnect, then using a high pressure airline, blow backwards into the jet to clear out any blockage. If you don't have a high pressure airline with nozzle, then use something like the nylon filament from a yard brush to poke into the jet, to try and clear the blockage.

Nov 05, 2012 | Cars & Trucks

1 Answer

Rear windscreen wash not working on Skoda Octavia


Remove cover from rear wiper arm (it is covering the wiper arm nut) gently ease off the plastic moulding in the middle of the nut try squirters if water is coming out unblock the water jet holes in the plastic moulding

Jun 29, 2012 | Skoda Octavia Cars & Trucks

3 Answers

How to install window tinting


Here are some step to install window tinting :

1. Clean windows.
2. Measure and pre-cut the film.
3. Trim the film.
4. Apply the application solution.
5. Apply tint to window.
6. Push all the water and soap towards the edge of the window, and blot away using a squeegee wrapped in paper towel.

Source : http://www.qualitytire.com/

May 19, 2012 | Cars & Trucks

1 Answer

2003 trailblazer, rear window washer fluid not coming out. Pump sounds like working and water comes out the bottom of the rear door. how can I fix?


check the rubber hose to the jet (spray nozzle) to see that it's not torn. then check the jet to see that it is not plugged up. (has a blockage) if it's has a blockage blowing it with a blow gun and compessed air will unclog it.

May 14, 2010 | 2003 Chevrolet TrailBlazer

1 Answer

Front wiper fluid is not spraying


when you try to spray can you here a noise from the moter, if so try to clean the hole were the water sprays out from with a fine pin.

Dec 28, 2008 | 2006 Subaru Forester

2 Answers

Windscreen washers not operating correctly. Water comes thru the jets but at low pressure


Get yourself a small gauge/thin piece of wire. Poke the jet holes with the wire until they spray like they used to. If you have an air compressor you can also blow through the sprayer with compressed air after poking them with the wire and they should be good as new. If that doesn't work you might have a blockage in the line at the one-way valve or at the pump in the washer tank.

Nov 28, 2008 | 2003 Hyundai Santa Fe

1 Answer

Mk 4 golf rear wiper too much water


the jet has a blockage and forcing the water out of the back of the jet clear the jet and put the pipe on properly yates210456

Oct 13, 2008 | 2000 Volkswagen GTI

2 Answers

2000 Hyundai Accent


Try removing the plastic panel underneath/forward of the RH wheel arch, the washer bottle is there, remove the pump by pulling straight out of the bottle. There is a plug and two hoses connected to the pump. You will probably find the mesh filter is clogged, clean and try it. Some washer pumps have a valve on the side where the hoses connect, do not try to dismantle this,

Jul 05, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...