Question about 2005 Mazda 3

1 Answer

Trying to remove rear tire

Even after lug nuts removed, cannot get tire off of hub/axle

Posted by on

  • Mark Egan May 11, 2010

    Kick the wheel and tire around the outside. If it's never been off before, sometimes they stick.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

Yup! Thats all you do. dont be afraid to get a little ruff with it.

Posted on Feb 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove front wheels of Acura 1996 3.2 TL


The large nut you see is most likely the axle retention nut.

It is NOT used to hold on the wheel.

The wheels on a 2000 Acura TL are secured to the wheel hub by 5 lug nuts.

If after removing the "lugs" the tire and wheel may be difficult to remove after a long period due to corrosion betweem the wheel and hub.

If this happens, tap the tire at opposite ends (like 12 and 6 o'clock) with a rubber or plastic mallet.

This should help to loosen the wheel so you can remove it.

Apr 15, 2013 | 2000 Acura TL

1 Answer

Replace front ball joints on jeep


Hello there,
To replace the front ball joint on your jeep. You will be needing these instruments, Lug wrench Jack, Jack stands, Wheel chocks, Socket set, Wrench set, Needle-nosed pliers, Hub puller, Ball joint separator, Hammer, Ball joint press, Torque wrench, then, Please follow the steps below:
Loosen the lug nuts on your Cherokee's front tires, using the lug wrench. Jack up the front end of the vehicle and brace it with jack stands. Place wheel chocks behind the rear tires to prevent rolling. Back the lugs off the lug nuts, and remove both front tires from your Cherokee.
Remove the bolts behind the calipers. Lift the calipers off the hubs and set them on a support so they do not stretch the rubber lines.
Pull straight out on the brake rotor to remove it from the wheel studs.
Remove the cotter pin from the end of the axle shaft that extends through the hub. This is best done with a pair of needle-nosed pliers. Remove the drive nut from the axle shaft, and set it off to the side.
Remove the three bolts retaining the hub. These 12-point bolts are on the rear of the assembly.
Separate the hub assembly from the knuckle; a hub puller will make this easier.
Remove the cotter pins from the ball joints, using the needle-nosed pliers. You must detach the pins from both the upper and lower ball joints. Use a socket and ratchet to remove the nuts at the bottom of each ball joint.
Insert a ball joint separator between the knuckle and the ball joint. A hammer can be a big help to drive the separator into place and force the knuckle and ball joint apart.
Use a ball joint press to remove the joints. The ball joint press will force the upper and lower ball joints out. Follow the instructions included with your press.
Insert the new joints, using the ball joint press. You must reverse the motion of the press this time, pressing down on the upper joint and up on the lower joint. Be sure that the joints are completely in place within the knuckle.
Reinstall the steering knuckle onto the new ball joints, and thread the nuts onto the bottom of the joint. Check your manufacturer's specifications for the torque requirements for the nuts. Insert the cotter pins, and bend them down around the nut.
Reassemble the hub and axle around the knuckle. When replacing the three bolts, torque them to your manufacturer's specification.
Place the brake assembly back into position, both rotor and caliper. Replace the two bolts you removed on the caliper. Torque the bolts to your manufacturer's specification. Place the wheel back on the Cherokee, and tighten the lug nuts appropriately. With the wheel secured, lower the vehicle back to the ground.
Hope this was helpful to you. Goodluck Elect_Comp

Sep 03, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

1998 ford explorer 2 wheel drive rear wheel bearing replacement


what about it?

conventional axle or limited slip? Get axle code off door sticker.

SECTION 205-02: Rear Drive Axle/Differential - Ford 8.8-Inch Ring Gear 1998 Explorer/Mountaineer Workshop Manual
IN-VEHICLE REPAIR Rear Wheel Bearing and Axle Shaft Oil Seal -4.0L SOHC and 4.0L EI, Conventional
Special Tool(s) swn~us~en~file=st1514a.gif~gen~ref.gif Axle Seal Replacer
T83T-1175-A swn~us~en~file=st1283a.gif~gen~ref.gif Axle Wheel Bearing Puller
T83T-1225-A swn~us~en~file=st1322a.gif~gen~ref.gif Axle Wheel Bearing Replacer
T83T-1225-B swn~us~en~file=st1326a.gif~gen~ref.gif Driver Handle
T80T-4000-W swn~us~en~file=st1185a.gif~gen~ref.gif Impact Slide Hammer
T50T-100-A
Removal
  1. Remove the axle shaft; refer to Axle Shaft in this section.
Axle Shaft Removal
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
    Loosen the lug nuts (1012).
    1. Remove the center cap.
    1. With the weight of the vehicle on the wheels, loosen the lug nuts.
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the wheel and tire assembly.
  1. Remove the axle housing cover (4033).
    1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
    1. Remove the axle housing cover bolts.
    1. Remove the axle housing cover.
  1. Remove the rear disc brake rotors (2C026); refer to Section 206-04 .
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Remove the U-washers (4N237).
    1. Push the axle shafts inboard.
    1. Remove the U-washers.
  1. Reinstall the differential pinion shaft.
    1. Install the differential pinion shaft.
    1. Install the differential pinion shaft lock bolt finger-tight.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal (1177).
    Remove the two axle shafts.
Installation
  1. Lubricate the lip of the inner wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal.
    Install the two axle shafts.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Install the U-washers.
    1. Position the two U-washers on the button end of the axle shafts.
    1. Pull the axle shafts outward.
  1. Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
    1. Install the differential pinion shaft lock bolt.
  1. Install the rear disc brake rotors; refer to Section 206-04 .
  1. Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant; refer to Axle Housing Cover in this section.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control.
    Clean the wheel hub and mounting surfaces.
  1. Install the tire and wheel assembly.
    1. Position the tire and wheel assembly.
    1. Install the lug nuts and lower the vehicle.
    1. Tighten the lug nuts.
    1. Install the center cap.


  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time.
    NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris.
    Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.
Installation
  1. Lubricate the new rear wheel bearing.
    1. Use Thermally Stable Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Use Axle Wheel Bearing Replacer with Driver Handle to install the rear wheel bearing.
  1. Lubricate the lip of the new axle shaft oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Use Axle Seal Replacer with Driver Handle to install the axle shaft oil seal.
  1. Install the axle shaft; refer to Axle Shaft in this section.

May 18, 2011 | Ford Explorer Cars & Trucks

1 Answer

How to disassemble the rear end in a 2000 gmc yukon and how to remove axles


Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Loosen the lug nuts on the wheel and tire assemblies but do not remove the lug nuts
  3. Raise and support the vehicle
  4. Remove or disconnect the following:
    • Wheel and tire assemblies
    • Axle lubricant into a suitable container
    • Rear driveshaft
    • Parking brake cable
    • Brake calipers
    • Shock absorbers from the axle brackets
    • Vent hose from the rear axle vent fitting
    • Nuts and the washers from the U-bolts
    • U-bolts, spring plates and spacers from the axle assembly
  5. Lower the axle assembly from the vehicle
To Install:
  1. Place the rear axle assembly under the vehicle
  2. Align the rear axle assembly with the springs then connect the spacers, spring plates and the U-bolts to the rear axle
  3. Raise the rear axle assembly into position
  4. Install or connect the following:
    • Washers and nuts to the U-bolts; Torque to: 59 lb-ft. (80 Nm) then, Torque to: 89 lb-ft. (120 Nm)
    • Vent hose to the rear axle vent fitting
    • Shock absorbers to the rear axle
    • Brake calipers (See: Brake Caliper)
    • Parking brake cable (See: Parking Brake Cable)
    • Rear driveshaft (See: Rear Driveshaft)
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  5. Fill the rear axle with lubricant
  6. Bleed the brake system (See: Brake Bleeding)
  7. Install the wheel and tire assemblies
  8. Lower the vehicle to the ground
  9. Torque lug nuts as follows:
    • Single Wheel: Torque to: 140 lb-ft. (190 Nm)
    • Dual Wheel: Torque to: 175 lb-ft. (240 Nm)
  10. Road test the vehicle to check performance
prev.gif next.gif

Aug 03, 2010 | 2000 GMC Yukon XL

1 Answer

How to get front rotors off and r they nock offs or do i have to take a nut off? 2000 chevy silverado 2wd


mcdevito75 here, They should be knockoffs, That castle nut is holding the hub / Bearing assembly to the axle, and once removed that nut has to be replaced with a new one, so it"s not reasonable that nut has to come off to get the rotors off. Try, remove the tire and lift the caliper assembly off the rotor, use penetrating oil, liquid wrench, W D 40 around the lugs as they may be part of the rotor assembly, Then with a hammer tap moderately around the edge of the rotor to loosen it, keep the gear in Neautrel so you can turn the rotor while tapping with the hammer and use that penetrating oil around the lug studs and around the hub. The rotor should fit around the hub where that nut is and thru the lug studs that hold the tire on the axle.

Jun 17, 2010 | 2000 Chevrolet Silverado 1500

2 Answers

Broken lug nut how to replace lug nut studs


take off tire. remove old stud by hammering it out with a punch. put a socket behind axle plate so as not to break the plate. when replacing, just start stud from back by hand, then use a lug nut to pull it in tight. when tight replace tire!

Apr 14, 2010 | 1999 Oldsmobile Intrigue

1 Answer

How do you change a wheel seal on a mercury mountaneer 1998 rear end


Axle Vent
NOTE: If the vent cannot be cleared, it must be installed new.
A plugged vent will cause excessive seal lip wear due to internal pressure buildup. If a leak occurs, check the vent. Make sure the vent hose is not kinked. Remove the hose from the vent nipple and clear the hose of any foreign material. While the hose is removed, pass a length of mechanics wire or a small diameter Allen wrench in and out of the vent to clean it. Connect the hose when done. The vent is located on the drivers side top of axle housing.
If you plan on doing most repairs yourself I would suggest buying a Haynes or Chilton manual for your particular vehicle. Or there are some data disks on e.bay($12-$15) For a cost of under $25, you can almost do any repair yourself with these manuals.Also there are online manuals like the site called ALLDATA where guides can be viewed for a fee. All these solutions will save you time and money, and give peace of mind over correct repairs. I can post you some procedures here also.
  1. CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
  2. Loosen the lug nuts (1012).
  3. Remove the center cap.
  4. With the weight of the vehicle on the wheels, loosen the lug nuts Raise and support the vehicle. .Remove the wheel and tire assembly.
  5. Remove the lug nuts.
  6. Remove the wheel and tire assembly. Remove the axle housing cover (4033).
    1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
    1. Remove the axle housing cover bolts.
    1. Remove the axle housing cover.
    2. a167554.gif
7.Remove the rear disc brake rotors You will have to remove the brake caliper to get rotor off.
8. CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
9.
1.Remove the differential pinion shaft lock bolt. 2.Remove the differential pinion shaft. 4fd1df0.gif 10.CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Remove the U-washers (4N237).
  1. Push the axle shafts inboard.
  2. Remove the U-washers.
  3. 9499075.gif
    11.Reinstall the differential pinion shaft.
    1. Install the differential pinion shaft.
    1. Install the differential pinion shaft lock bolt finger-tight.
    2. 91fc782.gif
      12.CAUTION: Do not damage the inner wheel bearing oil seal (1177). Remove the two axle shafts. 1848771.gif
CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time. NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris. Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.

0ffed5b.gifAxle bearing puller end..
Installation
Lubricate the lip of the inner wheel bearing oil seal.
Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
  2. Remove the differential pinion shaft.
  3. Remove the differential pinion shaft lock bolt.
  4. Remove the differential pinion shaft.
  5. 5a472e0.gif
    CAUTION: Do not damage the inner wheel bearing oil seal. Install the two axle shafts. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers.
    1. Position the two U-washers on the button end of the axle shafts.
    1. Pull the axle shafts outward.
    2. 345272a.gif
      Install the differential pinion shaft.
      1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
      1. Install the differential pinion shaft lock bolt.
      2. 49e064a.gif
                                                            Install the rear disc brake rotors; Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant
                                                            WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control. Clean the wheel hub and mounting surfaces. Install the tire and wheel assembly.
                                                            Position the tire and wheel assembly. Install the lug nuts and lower the vehicle. Tighten the lug nuts. Install the center cap. 6a78fd6.gif WHEW Hope this can help you

                                                            Mar 21, 2010 | 1998 Mercury Mountaineer

                                                            1 Answer

                                                            How do i change the driver side front hub assembly


                                                            The vehicle will need to raised on the left (drivers) side and supported. Remove the tire, then the brake caliper assy. Remove the rotor, then remove the axle nut located in the center of the hub assy. Remove the hub/bearing retaining bolts, and then the hub assy. Some times it is corroded into the steering knuckle assy. and will not seem to come out. If this happens, install the axle nut, and wearing safety glasses, pound onto the hub flange from the inside to the outside, until it comes out of the knuckle assy. Then remove the hub assy. Clean the knuckle hole where the bearing with 120 grit sand paper, so the hub/bearing assy will go into the knuckle without damage. Torque the axle nut to specs. Clean the inside of the rotor, where the hub meets it, so it sits flat against the new hub. Install the rotor, caliper assy. Install the wheel and torque the lug nuts to 100 ft pounds. Road test about 5 miles and recheck the lug nuts.

                                                            Jan 19, 2010 | 1998 Ford Explorer

                                                            1 Answer

                                                            How to replace lug studs on 2002 chrysler town


                                                            I'll try to help you. If you are having trouble with 3 out of 5 studs on one wheel you may want to go to an autoparts store or Salvage yard to look at the whole hub. Usually a press is used to remove the bolts so you would be taking off the hub anyway. When you pay for 3 bolts and labor you may be better off in a Salvage yard or parts place for a different hub. The rear hub on front wheel drive cars is like a trailer axle. Much simpler to remove mounting bolts and press in new bolt. But if rear has differential(rear wheel drive) it has an axle shaft. Would be easier to grind and drill out broken stud on car. You can draw new bolt into place by placing bolt through a socket and use the wheel nut to draw the bolt into the hub.

                                                            Jul 08, 2009 | 2009 Chrysler Town and Country

                                                            1 Answer

                                                            Replacing front left wheel bearing of chevrolet venture


                                                            before removning tire loosen lug nuts and axle nuts a little bit not all the way .to loosen axle nut you need a 1/2 inch break bar with deep socket or 1/2 battery power impact wrench.then raise vechicle use jack stands block rear wheels .then remove wheel disconnect wheel speed sensor .remove brake caliper and bracket then rotor .half shaft bolt.you need a tool remove front hub and bearings as a unit.from axle shaft.

                                                            May 13, 2009 | 2003 Chevrolet Venture Passanger

                                                            Not finding what you are looking for?
                                                            2005 Mazda 3 Logo

                                                            Related Topics:

                                                            75 people viewed this question

                                                            Ask a Question

                                                            Usually answered in minutes!

                                                            Top Mazda Experts

                                                            yadayada
                                                            yadayada

                                                            Level 3 Expert

                                                            70346 Answers

                                                            Colin Stickland
                                                            Colin Stickland

                                                            Level 3 Expert

                                                            22041 Answers

                                                            Jeff Turcotte
                                                            Jeff Turcotte

                                                            Level 3 Expert

                                                            6864 Answers

                                                            Are you a Mazda Expert? Answer questions, earn points and help others

                                                            Answer questions

                                                            Manuals & User Guides

                                                            Loading...