Question about 2002 Dodge Ram 3500 Truck

1 Answer

Removeing the oil pan

I need to know what I need to do to remove theoil pan so I can change the gasket?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

First of all drain the oil and then remove all bolts from the pan.

Posted on Feb 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove oil pan on a 2001 gmc Sonoma pick up truck to replace gasket


1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN ...

? 2:31
https://www.youtube.com/watch?v=1KsRTlnW7Cg
Sep 27, 2011 - Uploaded by JohnSmiths8379858
trying to reomove the oil pan to this truck has been sitting for about 6 ... 1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN REMOVAL "HELP!

Oil Pan Gasket: How to Change Oil Pan Gasket for 2001 ...

www.2carpros.com/questions/2001-gmc-sonoma-oil-pan-gasket
Mar 18, 2011 - How to change oil pan gasket for 2001 sonoma, can i get away with just raising the engine two inches to ... 2001 GMC Sonoma • 4 cylinder 2WD Automatic • 150,000 miles ... You need to remove the engine to get the sump off.

Nov 28, 2015 | GMC Cars & Trucks

1 Answer

HOW DO I CHANGE OIL PAN GASKET IN A 1997 ACURA TL


Drain the oil, Remove the bolts/screws holding the pan onto the bottom of the engine. Remove all traces of old gasket. Clean the mating surfaces. Use bearing grease to stick the gasket onto the engine. Replace the pan and all bolts.

Nov 14, 2014 | Cars & Trucks

1 Answer

How do I replace oil pan 1973 cougar 351c how long will it take to complete engine in car


Hi Negal,here's a link on how to do theoil pan replacement. Repair Guides Engine Lubrication Oil Pan AutoZone com Shouldn't take long at all.maybe a hour.

Sep 12, 2014 | Cars & Trucks

1 Answer

How to do a transmission fluid/filter change on a gmc 1500 2wd v8 350 step by step


Raise the vehicle. Refer to Vehicle Lifting. Place a drain pan under the transmission oil pan. Remove the oil pan drain plug. Remove the oil pan bolts. Remove the oil pan. Remove the gasket. Remove the magnet. Remove the oil filter. Remove the filter neck seal. The transmission oil pan gasket is reusable. Inspect the gasket and replace as needed. Clean the transmission case and the oil pan gasket surfaces with solvent. Install the filter neck seal. Install the oil filter. Install the oil pan gasket to the pan. Install the magnet into the bottom of the pan. Notice: Refer to Fastener Notice in Service Precautions. Install the oil pan to the transmission with seventeen bolts. Tighten the oil pan bolts to 11 Nm (97 inch lbs.) . Apply a small amount of sealant GM P/N 12346004 to the treads of the drain plug. Install the oil pan drain plug. Tighten the oil pan drain plug to 18 Nm (13 ft. lbs.) . Install Dextron Automatic Transmission Fluid. Lower the vehicle.

Jul 04, 2011 | GMC Sierra 1500 Cars & Trucks

2 Answers

Where is trans filter located


Hi,
The follwoing is from the GM Shop Technical Manual.
Changing the filter requires removing the transaxle oil pan and gasket,
Remove or disconnect

bendarden.jpg

  • Raise vehicle and suitably support.
  • Loosen oil pan bolts and drain fluid,
  • Remove oil pan attaching bolts.
  • Remove pan pan and gasket.
  • Remove the oiil filter using a long screwdriver pry filter neck out of the seal.
  • Check oil filter seal for damage or wear. If needed, remove and replace
Install or connect
  • install new oil filter and/or seal.
  • install the old pan gasket since it can be reused, unless sealing ribs are damaged. If damaged, use new gasket.
  • Install the oil pan and attaching bolts.
  • Tighten pan bolts to 13 lb. ft,
  • Lower vehicle.
  • Refill transxle to proper level with DEXRON III or DEXRON-IIE fluid.
  • Checkoil pan gasket for leaks,

May 21, 2011 | 1995 Buick LeSabre

1 Answer

How to replace oil pan gasket?


Very easy,dirty,messy, job. Grab few item from auto zone. Such as rtv sealant gasket itself, a blade or something to remove the old gasket. 4-8 quarts of oil 10w40 synthetic. Oil filter oil filter remover socket set. Run car for 5 minutes. Drain oils. Recycle it... Dart removing the screws around the oil pan. Once remove clean the surface remove the old gasket with shart razor blade make sure do not damage the surface where the gasket go. The gasket go between the oil pan and the engine mating surface . Clean the pan and clear as much gunk you can out the pump opening or tube. put rtv sealant ( some don't need the gasket because they r the gasket.) place gasket putt screw back it. Change filter refill the car with oil ( 4-8 depending on engine size) That's it.

Dec 29, 2010 | 1999 Ford Taurus

1 Answer

HOW TO CHANGE TRANSMISSION FLUID AND FILTER


jack van, use safty stands to hold up, put a pan under trany pan to catch fluid, remove blots holding pan,fluid will start to leak out.leave the front bolts for last ,that way theoil leaks out the back,after all bolts are removed then take pan down, pull filter out,install new filter with gasket ring for neck of filter, clean pan and trany, install pan gasket and bolt up.use cross pattern to tighten,just tight alittle dont crush gasket. put in 4 qts,run engine and run through gear, check fluid and add acording to dip stick,hope this is helpful.

Dec 24, 2009 | 1996 Dodge Caravan

1 Answer

How to remove oil pan from 1994 olds acheiva


raise car, remove any obstruction from out of the way of the oil pan. if you arent pulling the motor it will mean you need to drop the front k member. after that remove all bolts from pan, pry it off with a putty knife, remove old gasket with razor knife, reapply gasket, possibly adding RTV silicone if your car needs it. reverse all other steps and you are clear. unless you know for sure its just the oil pan leaking i would suggest changing front and rear main seals on the crank as well.

Oct 10, 2009 | 1994 Oldsmobile Achieva Special Edition

1 Answer

How do I change the tranny fluid in my 1998 cadillac catera


Fluid - A/T: Service and Repair
Transmission Fluid and Oil Filter Changing
REMOVAL PROCEDURE
1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
2. Place drain pan under pan
3. Remove oil pan bolts from front and sides only.
4. Loosen the rear oil pan bolts approximately four turns.
5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
6. Remove the oil pan bolts from rear oil pan and gasket.
7. Remove front oil pan bolts leaving one corner bolt in loosely.
8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
9. Remove the following remaining components:
^ The front oil pan bolts
^ The oil pan
^ The gasket
10. Remove the oil filter bolts and filter.
11. Clean the following components:
^ The transmission case
^ The front adapter case
^ The oil pan gasket surfaces with solvent
^ Air dry
^ All traces of gasket material must be removed
INSTALLATION PROCEDURE
1. Install the gasket.
2. Install the oil filter.
3. Install the bolts.
^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
NOTICE: Refer to Fastener Notice in Service Precautions.
4. Install the front oil pan.
5. Install the front oil pan gasket
6. Install the front oil pan bolts
^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
7. Install the following components:
^ Install the pan
^ Install the gasket
^ Install the bolts
^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
pan fill. Fill plug opening using and oil suction gun.
^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
9. Lower the vehicle.
10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

Sep 13, 2009 | 1998 Cadillac Catera

1 Answer

Changing oil pan gasket on 1989 Ford Aerostar


drain the oil from the pan and remove the filter.
Lift the car up and secure it . So it will not roll or fall. Remove the bolts from the pan using a 10 mm or so and a rachet and small extension. There are several bolts all around the pan. Remove the pan and remove the gasket. Clean up the pan and remove all gasket material from the pan. Install the new gasket around the pan and replace back.

Apr 05, 2009 | 1989 Ford Aerostar Cargo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...