Question about 1995 Jeep Wrangler

2 Answers

Loud squealing noise when clutch pedal is depressed

95 wrangler, 4cyl. 180000 miles. There is a loud squeeling noise when the clutch pedal is depressed. there is fluid in the reservoir. Have had jeep since 101000. clutch has not been replaced since I have owned it. Any ideas?

thanks,

dom

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Sounds like its slipping on its way out me thinks

Posted on Feb 16, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi Dom,
Probably the release bearing is worn-out.
In my opinion, you should look for good motor shop around your area.
Let them replace the release bearing, clutch lining assembly, and the pressure plate assembly.
Labor cost for that job is around 500.00 to 800.00 pesos.
I don't know the prices of the parts now.

I'm sure this will solve your problem.

eloysky

Posted on Feb 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch noise


Bearing noises in a clutch system are easily distinguished by running a few simple tests. Start the engine and leave the transmission in neutral. If a transmission makes noise when it is in neutral it is often a worn input shaft bearing. Now depress the pedal until the clutch just engages. This is the point where the release bearing is just contacting the pressure plate fingers. If you begin to hear a squealing sound this is likely a worn release bearing. If a whirling noise is present when the clutch pedal is fully depressed it is probably the pilot bearing.

Jun 09, 2014 | BMW 316i Cars & Trucks

1 Answer

High pitched squeal when jeep idles or during deceleration. soonafter, clutch pedal jumped violently under my foot followed by engine stalling out. could not depress clutch pedal after that.


It sounds like your clutch bearing has gone they are usually on a pendulum system it screeches before it starts to go. Best get it checked.

Apr 15, 2014 | 1995 Jeep Wrangler

1 Answer

Cannot depress clutch


may need a new one or ajust--bring it to a specialist or honest mech-not a dealer

Aug 17, 2013 | Ford Mustang Cars & Trucks

1 Answer

Loud squeeling noise when i push in the clutch


Without hearing the squeal, I presume its coming from under the bonnet and only when the clutch is pushed in if so, I would be fairly certain that it is the clutch thrust bearing. To check start the engine, depress the clutch so that the squeal is present. Then whilst it is squealing gently rev the engine, if the squeal varies at at then I would be 99% certain that it is the cause. Unfortunately the only fix for that is replacement of the clutch. hope this helps

Feb 26, 2013 | 2003 Suzuki Aerio

1 Answer

On2nd clutch 08 wrangler 1st one replaced @ 9000 mi.s throw out bearing makes noise again


I hope when the first clutch was replaced the throw out bearing was replaced. It sounds like you are either riding the clutch (foot resting on clutch pedal and partially depressing the clutch during normal driving) or the adjustment is incorrect. The throwout bearing should not contact the pressure plate unless the clutch pedal is depressed when adjusted correctly. The constant contact is what wears the bearing out prematurely.

Dec 31, 2010 | 2008 Jeep Wrangler

1 Answer

97 jeep wrangler sport, mechanic changes clutch


If the pilot bearing was the problem it would make noise with the clutch pushed and go away when you let it out. Have you checked the fluid level in the transmission?

Apr 03, 2010 | 1997 Jeep Wrangler

1 Answer

850 volvo has squeal when clutch pedal not depressed


THE PROBLEM IS MOST LIKELY A WORN-OUT THROWOUT BEARING

Apr 07, 2009 | 1994 Volvo 850

1 Answer

Clutch makes a squealing noise


Hello;
The throw out bearing is going oout. The reason you hear the squeal when you push in the clutch is that is when the throw out bearing spins up. Rest of the time it does not spin.It is irratating, You should replace the entire clutch assembly when you replace the throw out bearing. Hope this helps, rate me high.
Thanks;
Rich
RPM Northwest

Feb 02, 2009 | 1998 Dodge Dakota

1 Answer

2001 BMW 330i clutch vibration


u have a worn out clutch pressure plate release bearing, that is what u feel and hear..

Dec 22, 2008 | 2003 BMW 330

Not finding what you are looking for?
1995 Jeep Wrangler Logo

865 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...