Question about 2000 Dodge Grand Caravan

1 Answer

HOW TO REMOVE 2000 DODGE CARAVAN REAR SEAT

HEAR SIR:
HOW TO REMOVE 2000 DODGE CARAVAN REAR SEAT?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

There are 2 handles on the back of the seat where it attaches to the floor. If you hold the button on the handle and push it down it should release the seat from the floor. After this it just rolls out the back. Same for the middle seat if you need to remove it.

Posted on Mar 08, 2009

  • taczaps Jun 02, 2010

    The manual didn't say to press down. I'd been pushing the buttons in and trying to lift :P

    Thank you very much!

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the blower motor in a dodge 2001 caravan


Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      1549e60.jpg

      Fig. Removing the trim panel to access the rear blower motor

    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    823bf07.jpg

    Fig. The rear blower motor is held in place by four screws


To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember to rate this).

Nov 01, 2010 | 2000 Dodge Caravan

1 Answer

Torque specs for the main rear seal on a 2000 dodge caravan???


i am the owner of Alexander's Garage yu may contact me at 717-242-1749.

Feb 20, 2010 | 2000 Dodge Caravan

1 Answer

My abs lite is on and code says left rear sensor bad. I need to know the process to change it on a 2001 dodge caravan


1. Remove the left rear tire
2. Remove the left rear sensor
3. Install the new sensor
4. Put the tire back on

Oct 23, 2009 | 2000 Dodge Caravan

2 Answers

Rear window washer not working.


it could a blockage at the spayer outside .take a safety pin and poke in the small hole outside.
to check the button remove,it from the dash take a
12volt tester check to make sure you have poweon one side

Apr 12, 2009 | 2000 Dodge Caravan

1 Answer

Trying to remove/replace drivers seat 98 caravan


Should be able to slide the seat forward to access the rear bolts.

Mar 11, 2009 | 1998 Dodge Grand Caravan

1 Answer

Replace broken fuel door 2000 dodge caravan


If you're on the smallish side and pretty limber, you might avoid removing the rear wheel. If not, you will likely need to remove the rear wheel and put the van on jack stands securely. I would remove the underside splash shield and gain access from underneath. It looks like you will need to unscrew the plastic insert that surrounds the filler neck inside the area that is exposed when you open the fuel door. Make sure you get the vent hooked up correctly when you are done.

Jan 31, 2009 | 2000 Dodge Caravan

1 Answer

!990 Dodge Grand Caravan Rear Seat


If yours is a Braun Entervan conversion and the spare tire has been relocated to the inside rear behind the seat, your rear seats will not come out, they are bolted to the floor. From the factory, they are designed to unlatch and come out, but after the conversion, the undercarriage of your van is completely different, especially if you have a lowered floor, and even more so if you have a kneeling van. If you unbolt the rear seats, you will have to bolt them back in, they're not quick releae anymore. If you van floor is lowered (usually about 10") "High Water" has a whole new meaning for you, it doesn't have to be very high at all to flood your interior.
Good Luck,
Steve, Houston TX

Jan 05, 2009 | 1994 Dodge Grand Caravan

1 Answer

Middle seat selt belt 99 caravan


it is bolted to the seat frame you have to remove the bolt and nut. it's a torx bit size #60 and a metric wrench size 15 mm that you will need. please rate the solution...thanks

Sep 26, 2008 | 2000 Dodge Grand Caravan

1 Answer

Front seat remove


There are four bolts on the undercarriage that hold the seat down. You can remove these with a socket wrench.

Sep 09, 2008 | 2000 Dodge Grand Caravan

Not finding what you are looking for?
2000 Dodge Grand Caravan Logo

Related Topics:

803 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...