Question about 1994 Toyota Celica

1 Answer

HOW DO I REMOVE rear speaker panels from 1994 celica???

I have removed the speaker grill from the panel and have removed 3 screws that I can see, have secured the panel. what other steps need to be taken to remove this difficult panel?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

  • remove the hinged brackets for rear seats remove locking bracket too
  • open front door carfully pull up plastic scuff plate
  • lift rear seat (push clip in centre of each seat)
  • push back the panel hard from door piller
  • pull panel out at bottom and puch down top of panel.Pig of a job but can be done.

Posted on Dec 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove door panel on 2014 Buick Verano


Remove the two screws retaining the sail panel/speaker grille assembly and remove the panel/grille from the door. Remove the three screws retaining the front door trim panel to the front door.

Feb 16, 2016 | Buick Verano Cars & Trucks

1 Answer

How to remove inside door panel


REMOVAL


Roll door glass down.
Disengage two clips attaching speaker grille to door trim panel. They are at the front of the grille, one near the top, and the other one at the bottom.

8_29_2012_10_22_22_pm.gif

Remove three large washer-headed screws surrounding the speaker

8_29_2012_10_23_15_pm.gif

Remove access cover at front of door trim panel. Remove by prying at its rear edge.
Remove red courtesy reflector from lower tail or door. Disengage by prying at screwdriver notch at bottom of reflector.
Remove flag trim panel from door by prying off at two attachment clips points.
Remove seven screws attaching door trim panel to door.
One screw is located at lower rear screw pocket.
Three screws located along the bottom of door.
One screw located inside handle opening.
One screw located at the upper front.
One screw in the pull cup.
Disengage two hidden clips attaching at the rear of the trim panel, by prying off at two attachment clip points.
Lift trim panel upward and away from door, disengage trim panel from upper retainer channel.
Disengage clip attaching latch linkage to back door handle.
Disconnect electrical connectors as necessary, including lower foot light, If equipped.
Remove door trim panel from door.
INSTALLATION


Position door trim panel near to door.
Connect electrical connectors as necessary, including foot light, if so equipped.
Engage clip attaching latch linkage to inside door handle.
Lift the door trim slightly to get the lock knob into its bezel opening on the panel.
Place front portion of upper trim strip flange into retainer channel, while seating white forward locator pin into mating hole in sheetmetal at front of door.
Drive screw into forward locator cup.
With rear of panel slightly lifted, engage remainder of trim strip flange into retainer channel, working from front to back, pressing down firmly.
Engage two hidden clips attaching rear of door trim to their mating (green) grommet holes in the door. Press the rear of the panel firmly in toward the door, listening for engagement clicking sounds at BOTH of the clips.
Install seven screws attaching door trim panel to door.
One screw in the pull cup.
One screw located inside handle opening.
One screw located at the upper front.
One screw is located at lower rear screw pocket.
Three screws located along the bottom of door.
Snap screw covers closed.
Install three large washer headed screws surrounding the speaker.
Install speaker grille by first engaging rear edge hinge flaps to mating slots, then pressing grille on to seat the two clips at front.
Install red courtesy reflector by first engaging rear edge hinge flaps to mating slots, then snap front in to position.
Install access cover at front of door trim panel. First engage slots at front, then snap in at rear edge.
Place flag trim panel into position and engage clips.
Close door window.

Aug 29, 2012 | 2002 Chrysler Sebring

2 Answers

How to remove ford taurus window switch


Door Panels

Print


REMOVAL & INSTALLATION

See Figures 1 through 8
This procedure applies to both the front and rear door panels.


0900c152802604e4.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Remove the cover from behind the inside door handle by gently pulling it out to release the retaining tabs


0900c152802604e5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Remove the pull cup retaining screw cover and...


0900c152802604e6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: ... remove the retaining screw from the cup and lift the cup straight up out of the door panel


0900c152802604e7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Remove the two sail panel/speaker grille retaining screws and...


0900c1528026022f.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: ... remove the panel/grille from the door


0900c152802604e8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: The door panel is retained to the door by 11 retaining clips


0900c152802604e9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Carefully lift the door panel off of the door and...


0900c152802604ea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 8: ... detach the electrical connectors from the switches and remove the panel from the vehicle

  1. Remove the cover behind the inside door handle.
  2. Remove the screw from the bottom of the pull cup retaining the front door trim panel to the front door.
  3. Remove the two screws retaining the sail panel/speaker grille assembly and remove the panel/grille from the door.
  4. Remove the three screws retaining the front door trim panel to the front door.

Do not attempt to remove more than one pushpin at a time.
  1. Use a suitable tool to remove the pushpins from the door.
  2. Carefully lift the door panel away from the door.
  3. Detach the electrical connectors as necessary and remove the panel from the door.

To install:
  1. Installation is the reverse of removal.

Aug 15, 2012 | 1998 Ford Taurus

1 Answer

Attempting to remove plastic molding around passenger rear vent motor, having difficulty. any help would be appreciated


This is more difficult than it looks because the rear trim panels must be removed in a certain order as they overlap at their edges.

First remove the rear seat.
Remove the step panel from the floor near the side door opening.
Unbolt the 2 seat belt anchors.
Remove the trim panel below the lift gate (rear hatch opening.) Pry the screw plugs out with a small screwdriver and remove the screws.
Pry out the rear speaker grill using a flat blade screwdiver that has been taped to prevent scratches.
Remove the rear speaker mounting screws. Pull the speaker out and unplug the connector.
Remove the passenger side trim panel mounting screws.
Use a panel clip removal tool and pry the clips that hold the trim panel then lift the panel away.

Installation is the reverse of removal.

Apr 07, 2011 | 2002 Honda Odyssey

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

How do i car door panels safely


  1. Remove the cover behind the inside door handle.
  2. Remove the screw from the bottom of the pull cup retaining the front door trim panel to the front door.
  3. Remove the two screws retaining the sail panel/speaker grille assembly and remove the panel/grille from the door.
  4. Remove the three screws retaining the front door trim panel to the front door.

Do not attempt to remove more than one pushpin at a time.

  1. Use a suitable tool to remove the pushpins from the door.
  2. Carefully lift the door panel away from the door.
  3. Detach the electrical connectors as necessary and remove the panel from the door.

To install:

  1. Installation is the reverse of removal.
Door Panel

This procedure applies to both the front and rear door panels.


// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 30; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos'; c17hydro_23.gif

Remove the cover from behind the inside door handle by gently pulling it out to release the retaining tabs


c17hydro_24.gif

Remove the pull cup retaining screw cover and...



c17hydro_25.gif

... remove the retaining screw from the cup and lift the cup straight up out of the door panel



c17hydro_26.gif

Remove the two sail panel/speaker grille retaining screws and...



c17hydro_27.gif

... remove the panel/grille from the door



c17hydro_28.gif

The door panel is retained to the door by 11 retaining clips



c17hydro_29.gif

Carefully lift the door panel off of the door and...



c17hydro_30.gif

... detach the electrical connectors from the switches and remove the panel from the vehicle

Nov 13, 2010 | 1996 Ford Taurus

1 Answer

How do I replace speakers on a 1994 xj6 ?


Replacement of Front and Rear Door Speakers

Required Tools:

#2 Phillips Screwdriver (magnetic tip is useful)
9 mm Nut Driver
8” or 10” Flat Tip Screwdriver
Small awl or other sharp pointed instrument
Soldering Iron w/solder or 8 to 10 small wire **** splices
8 to 10 small machine screws -- #8 x ¾” or equivalent 8 to 10 small machine screw nuts & flat washers to match
Thread locking compound “Loctite” (optional)
6” wooden dowel of ½” diameter to be used as a drift
Small mallet or hammer

1) Whenever you are attempting to a remove door panel to gain access to the speaker, or any other electrical component, absolutely disconnect the negative battery cable. Battery power is supplied to each door window motor and it’s always prudent to de-energize these circuits before you attempt any panel work.

2) XJ40 door inner panels (front or rear) are comprised of an upper and lower section, which interface to provide complete inner door coverage. Neither panel is difficult to remove nor are any specialized tools required.


3) Remove the Upper Inner Door Panels as follows:

It’s a good idea to store all the removed parts and screws in the adjacent foot well for safekeeping and easy access when you are putting everything back together.

a) Using a small awl (or equivalent), remove the small “square” plastic cover for the inner door lock release mechanism (upper right side when facing inner side of door). It pivots towards the front of the car.

b) Using the #2 Phillips screwdriver, remove the inner door lock release mechanism plastic / chrome escutcheon. It’s held in place by a single machine screw. Pull out on the door lock release mechanism and the escutcheon is easily removed.

c) Using both hands, pull out on the wood veneer panel at the inner door lock release mechanism to provide clearance and slide the panel towards the front of the car. The panel is secured on the left side by slip-in clips and they release easily.

d) Using the #2 Phillips screwdriver, remove the two sheet metal screws on the left side. For the front doors only, lift the bottom of the rubber ventilation boot at the front edge of the door and remove the sheet metal screw. Additionally, for the front door only, use the large flat screwdriver as a lever to ease out the single “fir tree” type press-fit connector. Neither of the rear doors contains these two additional fasteners.

e) Using both hands, lift the upper inner door panel until it releases from the metal ridge along the window line. It doesn’t take much effort to remove the upper panel as it slides off vertically. Store it on the seats for safekeeping.

4) Remove the Lower Inner Door Panels as follows:

a) Using the #2 Phillips screwdriver, remove the sheet metal screw located at the upper edge of the lower panel.

b) Using a ½”small wooden dowel or equivalent drift, place it under the lower edge of the door handle screw access cover. Lightly tap each end of the access cover using the dowel and mallet in an upward direction to release the access cover. These covers can be tight if they have never been removed in the past, but they will release.

c) Using the #2 Phillips screwdriver, remove the sheet metal screw located in the middle of the door handle.

d) Using a small awl or equivalent, remove the bottom door light lens by releasing it from its locator at the rear and sliding it outwards from the door.

e) Using the #2 Phillips screwdriver, remove the lower panel securing sheet metal screw located in the middle of the bottom door light assembly. All sheet metal screw fasteners for the lower panel are now removed.

f) Using both hands (and the large flat screwdriver, if needed), carefully pull off the lower inner door panel by release the series of fir-tree type press-fit connectors along the sides and lower perimeter. Once the panel is removed, it can be laid horizontally on the seat as there is sufficient length of wire bundle to allow this movement. It is not necessary to disconnect the wiring harness, but if desired, the connectors can be released so that the panel can be moved to another more worker friendly location.

5) Remove Door Mounted Speaker as follows:

a) Disconnect the speaker positive and negative conductors by releasing the electrical connector.

b) Using the 9mm Nutdriver, remove the speed clip nut from each of the four (4) speaker fastener studs. Press the nutdriver down firmly to engage the speed nut … do NOT cut away any foam material as it is not necessary.

c) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the left (driver side) or right (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

d) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately above the speaker. It is located just below the upper sheet metal screw securing tab on the lower panel … the screw was previously removed in Step 4a.

e) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the lower right (driver side) or lower left (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

f) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the lower far right (driver side) or lower far left (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

g) Steps 5c, d, e and f will release the speaker / window lift pushbutton panel from the lower door inner panel. Removal of the sheet metal screws will allow the speaker panel to be pulled away from the lower panel by 3” to 4” to facilitate access for speaker removal.

h) With the speaker / window lift pushbutton panel eased back for working clearance, grasp the speaker with one hand while pressing the four (4) speaker studs downward through the foam supporting material. After the studs are clear from the foam material, the speaker can be removed from the panel.

6) Install New Door Mounted Speaker as follows:

Typically, base XJ40 models use 3.5” door speakers while the VDPs will use 4” door speakers. Though I believe it is possible to mount either type in either model.

a) Using the wiring supplied with the new speakers and insulated solderless **** splices, transfer the old speaker wiring electrical connector to the new speaker. Another alternate method is to simply solder the old speaker wires with connector to the new speaker terminals. This is a superior method for electrical continuity and strength of joint … although it does require some soldering skills.

b) Install the new 3.5” speaker by easing back the speaker panel and sliding in the new speaker. Normally, the 3.5” models will mount with only two fasteners.

c) Using two of the small machine screws with flat washers, place these fasteners through the speaker mounting lugs and press them up through the existing holes in the foam supporting material. Secure the screws with flat washers and matching nuts from the back side of the inner door panel. The use of thread locking compound (Loctite) is a nice touch to prevent loosening due to vibration.

d) Re-install the sheet metal screws removed in Steps 5c, d, e and f. This will re-mount the speaker panel. Don’t forget to re-connect the speaker wire connector at the door panel.


7) Re-installation of the inner door lower and upper panels is literally a reverse of the removal procedure. No hidden tricks.

8) Perform Steps 3 through 6 for the other doors and the job is complete.

9) Remove Rear Footwell Mounted Speaker as follows:

This sequence is good for both 4” and 5.25” footwell mounted woofers.

a) Using a small flat screwdriver as a lever, carefully ease off the grill.

b) Using a #2 Phillips screwdriver, remove the four (4) sheet metal mounting screws.

c) Ease out the old speaker and release the electrical connector for the speaker wires.

d) Transfer the old speaker wires and electrical connector to the new speaker using solderless **** splices or by soldering the old leads to the new speaker terminals.

e) Re-connect the speaker wires to the harness by joining the electrical connector.

f) Mount the new speaker and re-attach the necessary sheet metal screws.

g) Press the speaker grill into place.

h) Repeat Steps 9a though 9g for the other footwell speaker.

Mar 10, 2010 | 1994 Jaguar XJ6

1 Answer

How do i get to the rear speakers in a bmw 319i 1994?


Remove the screws from the speaker grills in the rear window deck, after that push them up from inside the trunk.

Sep 16, 2009 | 1994 BMW 3 Series

1 Answer

Side View Electric mirror can't adjust up enough for my height


You can manually push the mirror left or righ or up and down. It just ratchets on the plastic screw adjusters. It won't do any damage.
If you have floding mirros, make sure they are locked into position.

here's what inside looks like of 2002 mirror. I don't have 2005

6f1da12.gif
SECTION 501-09: Rear View Mirrors 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Removal and Installation
All vehicles
  1. Remove the front door trim panel (23942). For additional information, refer to Section 501-05 .
Vehicles with Mach 40 speakers
  1. If equipped, remove the speaker grille.
  1. Remove the speaker bracket.
    1. Remove the screws.
    1. Remove the speaker bracket.
    • Disconnect the speaker electrical connector.
Vehicles with speaker delete panel
  1. Remove the speaker delete panel screw cover.
  1. Remove the speaker delete panel.
    1. Remove the screws.
    1. Remove the panel.
All vehicles
  1. Disconnect the power exterior rear view mirror electrical connector.
  1. Position the water shield aside.
  1. Remove the power exterior rear view mirror nuts.
  1. Remove the power exterior rear view mirror.
    1. Push down on the mirror assembly to release the mirror flange.
    1. Roll the mirror assembly down and rearward.

Jan 21, 2009 | 2005 Ford Taurus

2 Answers

Driver side power window stopped working


The door panel is held on by plastic clips and 5 screws. 3 screws are on the bottom and 1 in the pull cup and 1 in the inner door handle.Then grab one of the corners and give a small tug, when you get some of the clips to pop out then proceed around the whole panel. To replace the panel take the clips out of the door with a fork and slide them back into the panel and then line it up on the door and use your hand like a hammer and bang the panel back on. Hope this helps

Jan 12, 2009 | 2004 Chrysler Sebring

Not finding what you are looking for?
1994 Toyota Celica Logo

700 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...