Question about 1995 Isuzu Rodeo

2 Answers

Cv joints wont come out of diff housing (95 Rodeo 4x4 diesel)WHY

Have remove tie rod ends hub etc and down too the hub at the diff
but the cv still wont come out,have welded a slide hammer to hub but still no luc.Whats holding this piece in?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The only way to remove the inner can wich is what the cv joint gose into you have to remove the whole housing from the truck and have it pressed out... there are two different half shafts used on the rodeo..THEY ARE NOT THE SAME..one is bigger than the other the brand is located on the half shaft behind the inner joint... to remove it you have to pull back the inner boot and remove the retaining clip on the inner joint and it will come right out I know this because I have to replace mine as well and I have talked to alot ppl on isuzu forums

Posted on Nov 26, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 409 Answers

You might have to remove the diff cover and remove the lock rings from inside the diff.

Posted on Feb 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a knock in the front end of a 1993 isuzu rodeo when in 4 wheel drive, only when going up hill. I've also had problems w/ the auto locking hubs disengaging. Could this be related? How do I insta


Your problem may be as simple as a bad ball joint, CV joint, tie rod end, hub assembly or other front end part. Something is not tight anymore. Have the front end checked and go from there. GOOD LUCK FRIEND.

Nov 15, 2014 | 1993 Isuzu Rodeo

1 Answer

Need instruction on cv shaft replacement


most front wheel drive cars are the same,remove large outer nut on axle/hub with air impact or breaker bar,disconnect tie rods ,ball joints,etc so half shaft can be pulled straight out,usually with a firm jerk or pry gently where axle enters carrier housing

Jan 12, 2013 | Isuzu Trooper Cars & Trucks

1 Answer

Can't get the front left cv off, i've undun the main hub nut (centre) broken the metal bands on both ends of the shaft not sure if i need to take off the whole front hub off to get out the Manuel...


You need to detach the ball joint and tie rod end so you can pull the hub away from the car to give you enough room to remove the end of the shaft from the hub.

Pull the cotter pin out of the tie rod end, then loosen the nut. Hit the tie rod end with a hammer and it will pop out. You need to give it a solid hit with the hammer.

There will be some nuts or screws on the bottom of the ball joint. Remove those screws/nuts.
Then pry the ball joint up until it pops loose and then you can pull the hub away from the shaft to remove the axle.

Sep 10, 2011 | 2001 Hyundai Santa Fe

1 Answer

Caere can i find parts diagrams for 2006 ford f150 4x4 front axle assem. and hub


This should be a great start but do suspect that you will need a few more items. Let me know if that becomes true.

0996b43f80202b8b.gif


  1. With the vehicle in NEUTRAL, position it on a hoist.
  2. Remove the dust cap.
  3. Remove and discard the wheel end nut.
  4. Remove the vacuum and vent line at the vacuum and vent port of the integrated wheel end.
  5. Remove the 3 integrated wheel end bolts.
  6. Remove the tie-rod nut and separate the tie rod from the knuckle.
  7. Remove the upper ball joint nut and separate the upper ball joint from the knuckle.
    CAUTION Do not damage the hub seal.

    NOTE Allow the steering knuckle to swing outward while keeping the halfshaft pushed inward.
  8. Once clearance is available, remove the halfshaft outboard end and integrated wheel end from the hub bearing.
  9. Remove the integrated wheel end from the halfshaft outboard end.
  10. To install, reverse the removal procedure. Use new a wheel end nut, tie-rod nut, and upper ball joint nut.
    CAUTION Do not install the integrated wheel end in the knuckle. It must be installed on the outer constant velocity joint housing.

    CAUTION Do not dislodge the integrated wheel end seal spring when installing the integrated wheel end on the outer constant velocity joint housing.

    NOTE Compress the integrated wheel end and install a vacuum cap on the vacuum port.

Apr 29, 2011 | Ford F-150 Cars & Trucks

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

1 Answer

Removing a drivers side cv joint on a 95 holden rodeo?


You have to remove the wheel then take the brake caliper off remove the nut from the upper control arm drop it down using a tye rod remover take nut off cv joint then use a pry bar to pop the cv joint from transmission now pull out of axle and remove.

Nov 29, 2010 | Isuzu Rodeo Cars & Trucks

1 Answer

Changing cvc joints 1997 accord


replace the entire CV axles. Support vehicle with jackstands by frame. Remove front wheels. Remove axle nuts. Remove lower balljoint nut. Separate balljoint from nuckle by banging hard with ball peen hammer on knuckle on spindle assy. Remove outer tie-rod nut. Separate tie-rod from steering nuckle by bangin on nuckle with ball-peen hammer. Use long pry bar to hold lower control arm down while simultaneously pulling hub/spindle assembly away from vehicle and pushing axle through hub toward transaxle. Go under vehicle and pry inner cv joint away from transaxle while holding axle assembly.
Install new CV axle in reverse of the disassembly.

Feb 21, 2010 | 1997 Honda Accord

1 Answer

How to replace a CV joint 2000 Cavalier Drivers side


Buy the right CV axle. Raise right front of vehicle. Remove wheel. use a lugnut and washers to secure brake rotor so that it is not flopping and trapping rust behind. Remove axle nut. Loosen nuts from outer tie rod end stud and lower ball joint stud almost all the way off, but do not remove them completely. Seperate the studs from knuckles by striking each knuckle with a ball peen hammer. After the tie rod and lower ball joint are seperated from the spindle knuckles, pry down on lower control arm and push end of axle through hub toward transaxle until hub and spindle assembly is free from axle/CV joint. Place drain pan under transmission. Carefully place pry bar between innner CV joint and transmission and pop axle assembly loose. Install new axle in reverse of the dissassembly.

Feb 21, 2010 | 2000 Chevrolet Cavalier

1 Answer

'93 Isuzu Rodeo, CV Joint replacement.


unbolt the tie rod end and the lower a arm and it should slide out of there

Jan 26, 2010 | 1999 Isuzu Rodeo

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

Not finding what you are looking for?
1995 Isuzu Rodeo Logo

590 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...