Question about 2003 Chevrolet Silverado 1500

1 Answer

Door lock broke

I had locked the door out of habit and my boyfriend yanked on the door cause he thought the door was unlocked and the door lock and i think rod in it broke i am not sure cause i don't know nothing about trucks or cars or anything. i feel really bad and have been crying alot. can someone tell what needs to be repaired so i can try to find something cheap thanx. :(

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 505 Answers

Rod is very hard to break it just the handle the clips broke so you just need a new handle

Posted on Feb 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Buick Rendezvous you can hear the relay clicking but the door locks will not open and close


Check for broke wires inside the boot from body to driver door , this is a common problem . If you don't find broke wire's , pull the door panel to get at driver door switch . Check for voltage an ground circuit .
Rendezvous Door Lock System Components
The power door lock system consists of the following components:
?€¢
Body control module (BCM)


?€¢
Driver door lock switch


?€¢
Front passenger door lock switch


?€¢
Door lock actuators in each of the doors


?€¢
Door lock system fuse into the BCM (BCM D 25A fuse)


Door Lock Operation
When the BCM detects a transition of either of the door lock switches to the LOCK position, it switches the door lock actuator lock control circuit to voltage. Since the lock actuator unlock control circuits are at ground potential within the BCM, the door lock actuator motors transition to the Lock position.
Driver Door Unlock Operation
When the BCM detects a transition of either of the door lock switches to the UNLOCK position, it switches the driver door lock actuator unlock control circuit to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the LF door lock actuator motor transitions to the Unlock position.
The driver door lock actuator unlock control circuit is a dedicated control circuit used only for the driver door lock actuator motor. This is done so that the driver door may be unlocked by itself using a keyless entry transmitter or an automatic door unlock function (if programmed).
Passenger Door Unlock Operation
When the BCM detects a transition of either of the door lock switches to the UNLOCK position, it switches the door lock actuator unlock control circuits to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the passenger door lock actuator motors transition to the Unlock position.
The door lock actuator unlock control circuits are dedicated control circuits used only for the passenger door lock actuator motors. This is done so that the driver door may be unlocked seperate from the passenger doors using a keyless entry transmitter or an automatic door unlock function (if programmed). This video on testing computer controlled door locks on a Subaru , doesn't matter . test yours same way > The BCM controls your door locks .
Are all of the power door locks inoperative from both door lock switches?

Oct 12, 2016 | 2005 Buick Rendezvous

1 Answer

Rear driver side lock stuck in the unlocked position.


The servo motor in the door lock may have failed, broke, or disconnected. An Authorized Chevy Dealer should be able to check it.

Aug 14, 2015 | 2010 Chevrolet Malibu

2 Answers

Vehicle entry problem


THAT really sounds like someone is pranking you by swapping your car for another car just like it.

Aug 05, 2014 | 2001 Mazda 626

2 Answers

2004 Jaguar S type remote control will not unlock doors. I have to manually open, thus setting off the alarm (which is very annoying). The remote will lock the doors, and then unlock if locking operation...


had a similar problem with a hyundai coupe , this turned out to to be the door lock mechanism in the drivers door, so could be the place to start, as i would have thought that generally the power locking technology is the same universally

May 20, 2014 | 2000 Jaguar S-Type

1 Answer

Peugeot 307 door lock


Probably the plastc clip the door lock rod goes thru broke.

Jun 06, 2017 | Cars & Trucks

1 Answer

The key fab will lock and unlock all doors except the drivers door and the lock botton in the car on the drivers door will not lock or unlock the drivers door either. How do I fix this problem?


sounds like the lock actuator in the driver door has failed, probably have to replace the actuator, but first check the fuses for the locks, chevy has a habit of using a fuse for the drivers door that doesnt power the other doors. If the fuses are ok, then its probably the actuator

Apr 19, 2011 | 2008 Chevrolet Equinox

1 Answer

My wife locked our keys in our car its a 2002 how does the inside of the door look, or what do I have to do to slim jim the door open? if you got a pic of the inside of the door that would be a lot easier...


You will need two plastic wedges and a piece of stiff wire (wire coat hangars work remarkably well) or a slim jim.
Insert the wedges between the metal portion of the driver door and the window to allow easier access for the slim jim/wire.
Slide it to the location of the lock bar. Hook the lock bar and yank to the right. This should actuate the locking lever and unlock the door.

Nov 03, 2017 | 2003 Nissan Altima

1 Answer

1998 Toyota 4runner driver side power door lock problem.


probably gonna have to take the door panel off. You say it wont unlock or lock with the key? if thats the case its probably broke inside the door.

Aug 20, 2009 | 2000 Toyota 4Runner

1 Answer

Power door locks going crazy


One of your door lock inside switches are bad.Find the one that doesn't feel right when you push it in either lock or unlock.The internal spring is broke causing the lock relay to keep try to lock or unlock until it gets hot & protects.

May 07, 2009 | 2001 Saturn SC

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...