Question about 1998 Toyota 4Runner

1 Answer

Power antenna on a 1998 Toyota 4Runner?

How do I replace the antenna on a 1998 Toyota 4Runner?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 517 Answers

If the problem is broken , buy only mastil antenna on toyota dealer, no need to change all antenna

Posted on Apr 21, 2009

6 Suggested Answers

pcastal
  • 90 Answers

SOURCE: replacing radio power mast on 2002 toyota 4runner

Sometimes you can put the new antenna cord in the motor, even with the old piece in there, and not have a problem. But, if it makes noise, the fender well needs to be pulled back, and the antenna motor removed enough to pull the back plate off,and remove the rest of the plastic cord. I have done MANY MANY of these. Its easy, some plastic clips, 1 10mm bolt, and some phillips screws.

Posted on Jan 26, 2009

tripletauto
  • 1450 Answers

SOURCE: 97 4Runner broken antenna; want to replace it with non-power antenna

You will just need to get a antenna that will fit your vehicle try a local stereo shop and wire it in.

Posted on Aug 22, 2008

  • 137 Answers

SOURCE: replace power antenna

its held in by the bracket on the botom of it and also the chrome nut arount the top of it... remove the nut from the top and the bolts from the base support bracket and then remove the antenna and power wires.. when installing replacement antenna secure the top nut first. then bolt base and reconnect antenna wire and power plug

Posted on Feb 24, 2009

  • 160 Answers

SOURCE: where is the fuel filter for a 1998 toyota 4runner?

on inside of frame rail drivers side 14mm line wrenches

Posted on Mar 16, 2009

  • 125 Answers

SOURCE: Not working = power rear window, power antenna, starter

it looks like the starter is bad, install a new one. the antenna gear is broken, needs to be replaced and you need to check the rear hatch for any obstructions

Posted on Apr 30, 2009

ZJLimited
  • 17970 Answers

SOURCE: Replacing heater core in a 1995 Toyota 4Runner

The heater core is a small heat exchanger located inside the truck, similar to the radiator at the front of the truck. Coolant is circulated from the engine through the heater core and back to the engine. The heater fan blows fresh, outside air through the heater core; the air is heated and sent on to the interior of the truck. For Toyota Pick-ups/Land Cruiser/4Runner 1989-1996 check this reference repair guide...



Heater Core - REMOVAL & INSTALLATION
(see Figure 1)

  1. Drain the cooling system.
  2. Remove the heater unit assembly. Have alot of towels handy for the leakage of coolant that may spill into your interior.
  3. Remove the fasteners securing the core to the unit, remove the plates and clamps. Pull upwards to remove the core from the unit.
To install:
  1. Inspect the core fins for any blockage. Using compressed air, clean them.
  2. Install the core into the unit placing the plates and clamps into position. Tighten the core screws.
  3. Install the heater unit into the vehicle.
  4. Fill the cooling system.
85a96e3.jpg

Fig. 1: Exploded view of the heater unit assembly-1996 4Runner shown





Heater Unit - REMOVAL & INSTALLATION
(see Figure 1)

Have alot of towels handy for the leakage of coolant that may spill into your interior.
  1. Discharge the A/C system (if applicable), using an approved recovery/recycling machine.
  2. Remove the cooling unit (if applicable).
  3. Drain the cooling system.
CAUTION When draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Disconnect the hoses to the heater core. Tag each one so that it may be correctly reinstalled.
  2. On some models you will need to remove the glove box assembly. On others, the instrument panel and reinforcement.
  3. At the heater case under the dash, disconnect the ductwork from the case.
  4. Disconnect the heater control cables from the heater case. Lift the spring clip holding the control cable to allow the cable to be manipulated. Don't deform or crimp the cables.
  1. Disconnect the wiring harness to the blower fan.
  2. Remove the three or four bolts holding the heater case to the dash. Because the inlet tubes project through the firewall, the unit will not fall straight down. It will need to be pulled into the passenger compartment and then brought downward.
To install:
  1. Lift the case into position and carefully place the inlet and outlet pipes through the firewall. Install the retaining bolts holding the case to the dash.
  2. Connect the wiring harness to the blower fan.
  3. Connect the control cables to their linkages. Each must be adjusted so that the motion of the dashboard lever causes the correct corresponding motion in the air door. Both the control lever and the door must reach maximum travel at the same time if full function is to be achieved.
    1. Set the dashboard control to FRESH. Lift the adjustment clip and adjust the air inlet cable towards the heater unit until the linkage is at its maximum travel on Pick-Up and 4Runner. For Land Cruiser, adjust the cable away from the case. Release the adjustment clip.
    2. Set the dashboard control to VENT (Pick-Up) or DEF (4Runner and Land Cruiser). Lift the adjustment clip and adjust the air flow control cable towards the heater unit until the linkage is at its maximum travel. Release the adjustment clip.
    3. Set the temperature control to COOL. Lift the adjustment clip and adjust the air mix control damper control cable away from the heater case until the linkage is at its maximum travel on . For Land Cruiser, adjust the cable towards the case.
  4. Connect or reinstall the ductwork. Make certain each tube is firmly and completely fitted on its port. A light spray of glass cleaner serves as a good lubricant; don't use too much.
  5. Install the glove box and/or instrument panel assembly.
  6. Connect the heater hoses. Use new clamps.
  7. Install the cooling unit (if equipped).
  8. Refill the coolant, then charge the A/C system (if equipped).



Hope this help (remember comment and rated this).

Posted on Aug 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to check which fuse is for the power antenna


What fuse disables the Automatic Antennae? - Toyota ...

www.toyota-4runner.org/.../70614-what-fuse-disables-automatic-antenna...
Aug 25, 2010 - Is there a fuse that disables the automatic antenna? ... For the price of 1 toyota power mast you get a whole assembly and it won't break again.

power antenna fuse location? - Corvette Forum


Nov 28, 2015 | Cars & Trucks

1 Answer

Trying to replace antenna mast on 1998 toyota 4 runner sr5. New antenna does not come with bezel so how do I remove bezel from old antenna and put on new antenna? Thx


Where did you get new antenna? If no instructions talk to the Autoparts store where you bought it. There should be instructions with the antenna. What happened to old antenna? A motorized antenna? If motorized, antenna has a white nylon gear tooth at back end. If it's not motorized it may not match. The bezel usually screws into the motorized device underneath the body work. Should be way to use small wrench to turn just like a nut to remove. Hope this helps. I've changed mine several times, by going throug the carwash without turning off the radio, but
different car.

Feb 27, 2015 | 1998 Toyota 4Runner

1 Answer

How do I turn off the antenna motor? it is broken and I just leave the antenna up. it makes this horrible noise everytime I start the truck.


should be a fuse in the (fusebox) just for the antenna. simply take the fuse out! make sure that fuse does not control anything else!!!

Jul 06, 2010 | 1998 Toyota 4Runner

2 Answers

The radio antenna doesn't go up or down. I can's even hear the motor making a noise.


possible fuse, if not unplug wire at antenna and put test light on....turn on key, if power there then antenna is done

Jun 16, 2010 | 1998 Toyota 4Runner

1 Answer

How to fix 98 toyota 4runners antenna? It stuck and won't go down or up. But I can hear motor spining when I start Radio. Can somebody Help me~?


This more than likely needs to be replaced.This is not very hard to do,usually a couple of nuts,a wire harness(plug),and you're good to go.You could try to lubricate(WD40) the arial slightly then try to gently push it down or pull it up,but if you have to force it the the drive assembly inside the antenna casing will probably brake.

Jan 01, 2010 | 1998 Toyota 4Runner

1 Answer

How do I determine the correct fuse associated with the radio, clock, and side windows on my 1997 Toyota 4Runner?


Hello,

Check out the instrument panel fusebox. Fuse 18. ACC 15 A: Car audio system, power antenna, clock, power rear view mirror control.

I also have clock removal instructions on my website if you need them www.autoclockrepair.com

Oct 13, 2009 | 1997 Toyota 4Runner

1 Answer

How can I disconnect the power antenna from my 2001 toyota 4 runner?


Does it keep running all the time and you just want it to stay up. They"re not that hard to replace.
The radio power triggers the antenna and the ant motor can be disconnected in the pass wheel well.

Jul 02, 2009 | 1995 Toyota 4Runner

1 Answer

Not working = power rear window, power antenna, starter


it looks like the starter is bad, install a new one. the antenna gear is broken, needs to be replaced and you need to check the rear hatch for any obstructions

Apr 21, 2009 | 1999 Toyota 4Runner

1 Answer

Replacing radio power mast on 2002 toyota 4runner


Sometimes you can put the new antenna cord in the motor, even with the old piece in there, and not have a problem. But, if it makes noise, the fender well needs to be pulled back, and the antenna motor removed enough to pull the back plate off,and remove the rest of the plastic cord. I have done MANY MANY of these. Its easy, some plastic clips, 1 10mm bolt, and some phillips screws.

Jan 01, 2009 | 2002 Toyota 4Runner

1 Answer

97 4Runner broken antenna; want to replace it with non-power antenna


You will just need to get a antenna that will fit your vehicle try a local stereo shop and wire it in.

Aug 22, 2008 | 1997 Toyota 4Runner

Not finding what you are looking for?
1998 Toyota 4Runner Logo

Related Topics:

1,345 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...