Question about 1999 Chrysler 300M

1 Answer

I NEED TO REPLACE THE OIL PUMP ON MY 1998 CHRYSLER 300, HOW DO I

I HAVE TO REPLACE THE OIL PUMP ON MY 1998 CHRYSLER 300M, IT DOES NOT HAVE ANY OIL PRESSURE

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

First of all put the car on ramps and for safety put something behind the rear wheel and then start taking the bolts out of the pan and once the bolts are out use a large rubber hammer to get the pan loose do not use anything to pry the pan off and you see your oil pump

Posted on Feb 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lound squeling sound when running


chek oil level if low add if full replace oil pressure sensor as for the squeel it could be bad belts or if its teh 3.5 get your water pump and timming belt changed

Feb 16, 2014 | 1998 Chrysler Concorde

1 Answer

Oil pump replacing/removal


A new oil pump for a Town and Country is only $40-50.00 to buy a new one, and the work you will do to get to it is a lot. Usually it is on the end of the crankshaft, so you get to replace the timing belt too.

Jan 16, 2014 | 1998 Chrysler Town & Country

1 Answer

Removing the power steering pump


Here's a link on how to remove power steering pump,and to the left of page,click on bleeding to finish job,have a great weekend.http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f802d67fe

Oct 20, 2012 | 1998 Chrysler Concorde

1 Answer

My 1998 caddilac deville low oil pressure light on


the low oil pressure light can be a faulty oil pressure sensor.But mostly its the pump itself. open the oil pan and check if the net is chocked if not then replace the oil pump and do install the new o ring supplied with the pump. And try changing the oil on time and a good brand is important. (if the problem still exists then u need to replace the crank barring and the cam bushings..Just kidding).

May 19, 2010 | Cars & Trucks

2 Answers

How do you replace the oil pump on a 96 chrysler lhs 3.5l


you need a haynes repair manual to show you photos how to remove timing belt and tensioner.and the crankshaft sprocket and vibration damper puller and installer.

Dec 01, 2009 | 1996 Chrysler LHS

1 Answer

How do i change the water pump on a 1999 2.5 v6 chrysler sebring?


Hello,

Removal:
Drain cooling system, remove the timing belt if necessary. Remove water pump mounting bolts. Separate water pump from water inlet pipe and remove.

Inspection:
Replace water pump if it has damage or cracks to pump body. Check the shaft seal for any leaks as evidence by traces of coolant from vent hole. Check for any impeller rubbing inside pump, and for loose or rough bearings.

Installation:
Clean all gasket and "O" ring surfaces. Install NEW "O" ring on water pipe (wet "O" ring with water to aid assembly). DO NOT allow oil or grease to contact "O" ring. Install NEW gasket on water pump, and install pump inlet opening over water pipe. Install pump-to-block bolts and tighten to specification 18 FT. Lbs. (25n.m). To complete installation, reverse removal procedure.

Hope this helps :)

Oct 19, 2009 | 1998 Chrysler Sebring

1 Answer

Stripped out oil drain plug


I have a similar situation on a 2000 VW Jetta. It's an easy fix. Do nothing to the plug, leave it there. I replace my oil using a small pump that was purchased from JC Whitney that removes the oil from the pan via the dipstick hole. Basically, it pulls the oil up via a long tube and into some container. Works fine, I recommend it. Check it out here: http://www.jcwhitney.com/autoparts/Product/Pr-p_Product.CATENTRY_ID:2009567/c-10101/Nty-1/p-2009567/Ntx-mode+matchallpartial/N-10101/tf-Browse/s-10101/Ntk-AllTextSearchGroup?Ntt=oil+change

Aug 25, 2009 | 1998 Chrysler Concorde

1 Answer

I need the location of the oil pump on a 1998 dodge ram


Remove the oil pan, it is mounted at the rear of the engine with a tube and screen attached. Be sure to prime the new pump before installing it.

May 12, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

Stripped oil pan plug


You should replace the pan. Pan saver plugs are for temporary use only.

Mar 30, 2009 | 1998 Chrysler Concorde

Not finding what you are looking for?
1999 Chrysler 300M Logo

Related Topics:

509 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...