Question about 1992 Chevrolet Lumina

2 Answers

I NEED A DIAGRAM OF 92 LUMINA SEDAN FRONT BREAK ASSEMBLY

I HAD A SCREW FALL OUT OF FRONT BREAK ASSEMBLY. IT APPEARS TO HAVE AN ALLEN HEAD ON IT. NOT SURE WHAT IT IS CALLED. IT SECURES THE BRAKE ASSEMBLY TO FRAME.

Posted by on

  • Roberta Smith
    Roberta Smith May 11, 2010

    you need to know where it goes or where to get one ?

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,902 Answers

Caliper bolt.
There are two on each caliper one high one low that attach to the frame

Posted on Feb 14, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 142 Answers

That is the brake caliper bolt. It secures the brake caliper to the caliper bracket.
Please remeber to rate this fix.

Posted on Feb 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The rotor will not come off to get to the wheel hub assembly. Am I overlooking something ?


Look for a screw that holds the rotor to the hub. Probably a phillips head or allen head. It will be on the face of the rotor between two lug studs.

Jan 16, 2011 | 2003 Mazda Mazda6

1 Answer

Rear view mirror fell off...how do i get metal mount out of mirror


some have a small set screw in the center an allen screw or torks screw and some just slide in take a flat head screw driver and carefully pry it up and it will slide towards the top and out hope this helps please dont forget to rate my solution

Aug 10, 2010 | 1997 Chevrolet Lumina

1 Answer

What tools are needed to change the front disk brakes on a 1988 cadillac sedan deville


Jack, big screw driver,allen wrench to fit caliper bolts, and wrench to fit bleeder screw. Lug wrench

May 20, 2010 | 1988 Cadillac Sedan DeVille

1 Answer

I have a 92 lumina euro i have no rear breaklights


yOU WILL HAVE TO PLACE THE sWITCH IN THE STEARING COLUME IT COST ABOUT 90 DOLLARS.

Apr 17, 2010 | 1992 Chevrolet Lumina

1 Answer

Where can I go on the web to see a diagram for the head assembly for my 92 chevy lumina


Autozone.com register and look at the repair manuals for your car I just did a 95 cutlass 3.1 and they had a step by step

Apr 11, 2009 | 1992 Chevrolet Lumina

1 Answer

Replacing driver's side mirror on a 1994 Chevy Lumina sedan


There are screws that hold the door panel on. They are typically located behind the small round plastic covers. If you look at the bottom of the door handle, you will see them. Also on the door lever, there might be a screw. After removing all of the screws, take a flat head screw driver, and gently pry up the panel. There are plastic clips that hold the panel securely to the door. Doing this will pop them out one at a time. Once the door panel is loose, lift it up, and it should come right out. Be sure to disconnect any wiring harness connectors before fully removing.

Mar 24, 2009 | 1991 Chevrolet Lumina

1 Answer

Fuel pump tune up


On the fuel pump if its diesal there are to adjustment screw. The first one is looking from the front of the motor is on the left hand side of the pump under the throttle linkage. to get to it you have to remove the side plate just take one bolt out and lossen the other one or the plate will fall down in under the manifold. Once off turn the engine over manually with a 15/16 socket on the crank. Bring the mark on the harmonic balancer and the engine together look inside the pump there should be a allen head screw showing you may need a mirror to see in. If you dont see the screw head turn engine over one complete turn. Know take a 5/16 allen key and turn the screw, only turn it a max 1/4 turn clockwise to much and you egt's will get to high. Now reinstall plate. This setting is for under max torque. 2nd screw is located at the fuel line going from the filter to the pump. On the the pump where the line goes in diconnect the line. Now some pumps have a brass adaptor take this off. Next take the same 5/16 allen key and tune the screw max 1/4 ture clockwise. reinstall adaptor and line.

Dec 06, 2008 | 1993 Ford F350

2 Answers

Removing the inside door lever, front driver's side


some of them have plastic hooks on them also try sliding it up down left and right it should pop loose and you will be able to pull it out

Nov 13, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1992 Chevrolet Lumina Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...