Question about 2004 Mazda 3

1 Answer

2005 Mazda 3 starter replacement

How do i replace the starter on a 2005 Mazda 3?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mazda Master
  • 6,674 Answers

Scroll down when you click on this link, and find your engine, click on pictures to expand.

Posted on Feb 13, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2007 Mazda CX7 wont crank

Is the car in neutral/park? Not trying to be rude, but this happens more than you can imagine.

1. Test battery. If bad, replace.
2. Turn key while someone else taps on the starter. If it starts, replace the starter. If not....
3. Check starter relay. If it is not clicking, replace it. If it is clicking....
3. Put a pry bar and socket on the crank pulley bolt. If it won't move, you have a locked engine. If it moves....
4. Test the neutral safety switch. If it's OK....
4. Replace the starter.

Nov 22, 2016 | 2007 Mazda CX-7

1 Answer

How do I disconnect a starter to replace it on a 2005 Mazda Tribute 2.3l

Disconnect the battery ,,Remove the large cable running to the starter,then the small one,remove the bolts holding it to the bell housing,and then remove the starter.

Nov 12, 2016 | 2005 Mazda Tribute

1 Answer

2005 mazda trubute won't start and i replace 40amp and got it work and it drive for a while and then it blow again

Mazda Tribute Questions - CarGurus > Questions > Mazda

CarGurus2001 Mazda Tribute 3.0 Wont Start. out shopping one ... 0. Report. rebel54 asked a2005 Mazda Tribute i Maintenance & Repair question about a month ago ...

Tribute won't start - Mazda Forum - Mazda Enthusiast Forums > ... > Mazda Vehicles > Mazda Tribute
May 22, 2007 - I have a 2002 Mazda Tribute V6. On Sunday it wouldn't start. ... 2005Tribute won't start! rizakag, Mazda Tribute, 4, 03-27-2006 09:29 AM ...
Why does my fuse in my 2005 mazda tribute keeps blowing > Questions > Mazda > TributeCarGurusSep 4, 2014 - Why does my fuse in my 2005 mazda tribute keeps blowing when I try to switch gears?Electrical problem - 2004 Mazda Tribute - > Questions > Mazda > Tribute > 2004 Mazda TributeApr 5, 2011 - Electrical problem on 2004 Mazda Tribute ... meter on the battery cable note the battery draw then remove fuses one at a ... 2005 Mazda Tribute.2005 Mazda Tribute, Fuse #3 Blows, No Tail

Jan 30, 2016 | 2005 Mazda Tribute

1 Answer

Replace water pump belt drive mazda tribute 2005

Cut old belt off and slip the new belt on and bump starter to get on pulley

Nov 03, 2011 | 2005 Mazda Tribute

1 Answer

I have a 2005 mazda 3 and I think that the starter is buisted how can I fix this without going to a shop?

easy answer, you can't..
You may be able to get a second hand unit and then remove your existing starter and fit the replacement but I would NOT advise you to disassemble the starter motor yourself.
There are parts inside the motor (bushes and brushes) that will be damaged by incorrect disassembly. The springs which maintain contact between the brushes and the commutator can (and do) pop out and disappear into the wide world and replacing them can prove difficult.
The solenoid WILL be damaged if you attempt to disassemble it incorrectly and some solenoids have several small parts which will fly out and end up in the same place as the brush springs, the same place socks, earings and loose change go to.. the land of nowhere.
So, either change the starter yourself or bite the bullet and take the starter to a qualified person..
Remember, if you really want to remove the starter yourself, disconnect the negative battery cable at the battery BEFORE you do anything else..

Dec 19, 2010 | 2006 Mazda 3

1 Answer

Mazda6 MTX random starter misengagement? New clutch, flywheel, starter, & battery. It does not grind, bind, click, just spins. Usually after a turn or two it cranks fine. I thought the old flywheel was...

check your battery find someone with a load tester, or parts store if battery checks out good and all cables are clean your starter is the problem just because you replaced it doesnt mean its good .

Nov 27, 2010 | 2005 Mazda 6

1 Answer


2005 mazda 3 front wheel bering left side are they pressed in and tools needed 2 replace bering

Sep 05, 2010 | 2005 Mazda 3

1 Answer

How do you reset starter for a 2005 mazda 3 i sedan after it has bees in an accident and driver side airbag has deployed??

The computer will not let the car start until the air bag circuit has been maintenanced.

Aug 23, 2009 | 2005 Mazda 3

Not finding what you are looking for?
2004 Mazda 3 Logo

3,478 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

78010 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8832 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides