Question about 1999 BMW 323 Series

1 Answer

Hazard lights my hazard lights flash once while im driving for no reason i think it a short in the switch , how do i remove the hazard button?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Faulty hazard switch get a small screwdriver and pry it out gently

Posted on Feb 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My Hazard Lights come on and can't turn off


Hi Todd:
I'd be thinking that the switch is defective.
The hazard lights are there for a reason so I would not disable them.
My suggestion?
Get the switch checked.

Aug 26, 2015 | Cars & Trucks

1 Answer

The hazard light switch broke and my hazards won't quit flashing tired sticking two screws in there now blinkers don't work


At this point you will need to replace the multifunction switch. It looks like used may be a good option for your vehicle. This is a relatively easy part to replace. You will need a couple TORX sockets but other than that its pretty straight forward once you remove the column covers.

Apr 10, 2013 | Cars & Trucks

1 Answer

How do i reset central locking on a micra 04 reg


Try the following:

"KEY FOB PROGRAMMING
NISSAN
SYSTEM DESCRIPTION
The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and hazard reminder. When the doors are locked and
unlocked the unit flashes the hazard lights once for lock and twice for unlock.
A maximum of four remote controls are allowed to be programmed.
ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II
Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.
Procedure
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key?s.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key?s for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds."

Mar 12, 2012 | Nissan Cars & Trucks

1 Answer

My turn signals will not turn on outside or in the dash


if you check fuses to turn signal lights and hazard fuse problem could be in hazard switch or multifunction switch.

Nov 22, 2011 | 2003 Oldsmobile Alero

1 Answer

1999 Lincoln Continental was in for repairs and now my turn signals and break lights dont work. Im being told it's something to do with the anti theft system because the battery was unhooked. The...


I suspect there is a problem with the turn signal/ hazard switch. turn the turn signal on left or right, if it doesn't flash, grip the hazard button and gently wiggle it around, if the signals start flashing, replace the turn signal switch. The Brake lights are wired through the turn signal switch, if the 3rd brake light works, the brake switch is OK. I don't think it has anything to do with the anti theft system (at this time)

Sep 21, 2011 | 1999 Lincoln Continental

2 Answers

The hazard lights are sticking on and draining the battery


Hi.

Replace the hazard lights switch.

Series 3 hazard light switch malfunctions are quite common. The switch may not work, or like in your case, it may short and drain the battery.You can find the procedure to remove the switch summarily described on this forum.

The switch can be tested disconnecting it from wires, and using an Ohmmeter on its contact to ensure it is opening and closing fine, and not sticking.

If the switch is fine, wiring, alarm system and crash sensor must be tested. The most common reason for this kind of problem is the switch itself.

See also:

Hazard Lights turning on by themselves.

Hazard lights keep coming on.

Regards.

Ginko.

May 19, 2010 | 2001 BMW 325

1 Answer

2001 Prelude hazard lights come on while driving


you can remove the flasher unit as a temp fix

Jan 10, 2010 | 2001 Honda Prelude

2 Answers

Indicators not flashing on Audi TT


i believe the audi uses two relays for the turn signals and hazzard lights so it would appear the turn relay has failed. it should be located under the dash near the steer column.... seems to me me they have some shielding under the dash so it may be hard to get to.

May 23, 2009 | 2002 Audi TT

1 Answer

Hazard lights flash by themselves, doors won't stay locked (unlock by themselves) key fob won't work.


I has a similar problem and I just took the battery out of my remote. I think there is a problem/ short in the remote. It's as if the button is being pressed when it is not. I will use my spare one in the mean time. It was driving me crazy becuase I was driving long distance at the time and when I removed the battery it stopped. I hope this works for you!

May 11, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
1999 BMW 323 Series Logo

Related Topics:

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...