Question about 2000 Buick LeSabre

2 Answers

Want to change bulb in turn signal on bottom front on driver side

Want to change bulb in turn signal on bottom driver side. How do i get to it ?

Posted by on

  • Anonymous Mar 18, 2014

    Passenger side front bulb.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

UNSNAP BLACK PLASTIC UNDERNEATH FIXTURE.REACH IN AND TWIST SOCKET TO REMOVE. PULL SOCKET DOWN AND REPLACE BULB. REVERSE STEPS TO REINSTALL. THIS IS ALL DONE FROM UNDERNEATH CAR.

Posted on May 30, 2009

  • handymanJohn Jun 17, 2011

    . I had to use the JACK to slightly lift the vehicle up enough for me to get my BIG head under the left front corner and look up into the bumper area. I removed 4 plastic push/pull TABs (that look similar to screws). I first removed 2 push/pull tabs that hold the lowermost horizontal plastic protective cover (black in color) to the adjacent front bottom bumper protective plastic. I also removed 2 push/pull tabs that fasten the same lowermost horizontal plastic protective cover to the adjacent ‘wheel side’ protective cover near the internal fender cover. This allowed me to then bend and mold the horizontal black protective cover up toward the hood so I could view the inner portion of the plastic bumper where the electronic connector (bulb) inserts into the yellow front blinker housing. I twisted the connector and it pulled out giving me access to the bulb. I purchased a new bulb, protective coating jell, coated the connector and replaced the bulb. Re-installed the connector, twisted it into place and reassembled the protective covers and re-inserted the push/pull tabs. Worked great and was very easy.

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 52 Answers

The lens should be screwed on from the outside.

Just remove the cover and replace the bulb.

Can you get to it from under the hood?

Posted on Feb 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front driver's side signal light does not work. Changed the bulb and it still does not work. The driver's side rear works and the passenger side works (front and back). Also, when the signal arm is pushed...


when a bulb fails on one side of the indicators the other bulb, same side, flashes faster, SO.you have just answered the question yourself,as you have replaced the bulb with a new one, the contacts for the new bulb are at fault.

Sep 11, 2010 | Hummer H3 Cars & Trucks

1 Answer

Driver front turn signal does not blink. front


This may have more then one bulb in the front or possibly a bad socket try wiggling the new bulb in the socket to see if it will work.Compare all turn signal lights that come on the passenger side to those drivers side.Some vehicles also incorporate sidemarker lights with the turn signals.

May 29, 2010 | 2001 Pontiac Aztek

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

2 Answers

2002 Hyundai elantra driver side turn signal not working outside


This simply means that the front driver side turn signal bulb has failed. Replace it.

Oct 28, 2009 | 2000 Nissan Maxima

1 Answer

2006 pt cruiser on drivers side rear turn signal


The turn signals flash depends on each and every bulb working correctly. When one bulb fails, you will notice a change in the flash frequency, as you describe.

Replace or repair the bulb that is not working, and you should be good to go.

Doc

Sep 14, 2009 | 2006 Chrysler PT Cruiser

1 Answer

Want to change bulb in turn signal on bottom front of driver side


If there is no screws on lens, you may have to acsess it from under car, or under hood, twist plug and should come out to chg. bulb.

Feb 13, 2009 | 2000 Buick LeSabre

3 Answers

Can't figure out how to change the bulb for turn signal on Jeep


I just changed both bulbs in my 1998 Grand Cherokee. These solutions made it possible, but i will offer some clarification and photos. First of all, all 4 screws are torx T20 as emoesmoe mentions, none are phillips. there are two bulbs that blink: the larger amber bulb is the turn signal light--dealer was cheaper than autozone and only had to purchase one bulb; the other bulb is called a side marker and it also blinks with a turn but stays on with the headlights. see photos that go along with the first two solutions. the first photo shows step one the first screw to take out. second and third photo are step two removing the second screw. the last photo shows the exposed screws to the turn signal housing after the uper light houseing has been removed:
401eede.jpgf714392.jpg44dea1e.jpg5f1eaed.jpg

Nov 12, 2008 | 2000 Jeep Grand Cherokee

1 Answer

How to change front driver side turn signal bulb


For Front turning signal, you need to remove the whole head light system to get to turn signal. 4 screws attach it to the car's body. Make sure to remove the lamps first and disconnect the switch for the turn signal lamp. Just replaced it last week myself.

Oct 15, 2008 | 2003 BMW 5 Series

Not finding what you are looking for?
2000 Buick LeSabre Logo

438 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...