Question about 1992 Honda Accord

1 Answer

Car was stolen broke the ignition

Ok so how do you do you take out the ignition. i cant turn over the key it is stuck in off. i need it to turn to the on so the thing will slide out but i cant get the thing to turn. is theres button somewere that lets yoou do this

Posted by on

  • spauldie Apr 18, 2009

    I need to replace the ignition key cylindar in my 2000 chevy astro and can't get it out. Help please....

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,596 Answers

REMOVAL

  1. On models equipped with airbag, disarm airbag as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
  2. On all models, disconnect battery ground cable.
  3. Remove ignition switch as described under STARTING AND CHARGING SYSTEMS/COMPONENT REPLACEMENT AND REPAIR PROCEDURES/IGNITION SWITCH.
  4. Remove key light case from lock body, if equipped.
  5. On 1989 Accord models, place ignition lock cylinder in the ACC position.
  6. On except 1989 Accord, place ignition lock in the I position.
  7. On all models, position suitable punch into hole on lock cylinder housing and depress pin, then remove lock cylinder from housing.
INSTALLATION

  1. On 1989 Accord models, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the LOCK position.
    2. Rotate key until it is almost at the ACC position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to ACC position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. On except 1989 Accord, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the O position.
    2. Rotate key until it is almost at the I position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to I position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. Install ignition switch and connect battery ground cable.
SRS wire harness is routed near the ignition switch.

CAUTION:
  • All SRS electrical wiring harnesses are covered with yellow outer insulation.
  • Before disconnecting the SRS wire harness, install the short connector on the airbag.
  • Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring.
IGNITION SWITCH
  1. Remove the steering wheel, then remove the steering column covers.
  2. Disconnect the 7-P connector from the under-dash fuse box.
  3. Insert the key and turn it to "0."
  4. Remove the 2 screws and replace the base of the switch.

Posted on Feb 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove ignition without keys


if you have a metal bit for your drill that's small enough to drill a hole into the middle of the key:
drill a hole into the center of they key. stick in something into the hole (preferably a rod of metal) with superglue on it and gently try to turn the ignition after it's properly dried.

Sep 30, 2015 | 1989 Toyota Camry

1 Answer

The car will not turn off the key is not stuck, I can take the key out but it won't turn back far enoug


Replace the ignition switch, Not the key part. It has fell apart on the inside .

Sep 07, 2014 | Ford Focus Cars & Trucks

1 Answer

The ignition is stuck in the on position and will not turn off in a 1992 lumnia


need a new ign lock--junk yards have used ones but the key has a chip init and wont match--go to napa and xplain

Nov 20, 2013 | 2003 Chrysler Town & Country

1 Answer

Ignition switch stuck will not turn wont ether way


Two causes for this:
(1) steering wheel needs to be turned, then try key again.
(2) faulty ignition switch in need of replacement (including a new set of keys).
When starting a car, the ignition is locked if the wheel has been rotated, which is an anti-theft
feature: the car thinks its being stolen when the wheel is turned while there's no key in the ignition.
To fix: turn the wheel back and forth, returning it (one way or another) to the original position
when the car was turned off, and unlocking the ignition, allowing you to start your car.

May 29, 2011 | 1996 GMC Yukon

2 Answers

2003 chevy tahoe with key stuck in ignition. vehicle previously broken into and stolen with scewdriver to ignition. ignition replaced. key now stuck and cannot turn vehcile off. can shift to driver,...


I have towed several of these with same problem. Sounds like to me it needs to go back in for the ignition switch again. Unless it's not going into park. If it's not going into park it would be a shift linkage issue and needs to be adjusted. Chris J.C. Towing & Recovery

Apr 09, 2010 | 2002 Chevrolet Tahoe

2 Answers

My key is stuck in ignition and wont turn or come out do you no what is wrong?


your going to need to replace the igniton or the electrical switch part in the back of switch may have broke apart and jammed it,take it apart and seeif the key turns once the switch part is off the key part,(electric ignition switch is removed from the cylinder lock).

Mar 04, 2010 | 1998 Saturn SL

1 Answer

My 1997 audi a4 the ignition key is stuck. what


OK first thing- Car has to be in park to pull the key from the ingnition. if it is and you still cant pull it, rock the wheel back and forth alittle (sometimes the columb lock doesnt lock properly and you cant release the key until it locks, rocking the wheel usually fixes this problem). and the last possibility is that the tumblers in your ignition have broken, when this happens you cant pull the key from the ignition because you cant turn the key back to the off possition all the way. when this happens you don't want to pull the key because you risk not being able to put it back in the ignition later and are forced to replace the ignition so you can drive your car. However if the tumblers are indeed broken you will have to replace the ignition anyway, atleast by leaving the key in it you can still drive the car until its replaced

Dec 27, 2009 | 2001 Audi A4

1 Answer

Igniton broken


well first off all. insurance should cover all damages. and second a screw driver would not work. first drill out the lock then you can use a screw driver. if u want it fixed just simple get a new switch it will cost you no more then twenty dollars at the dealership

Feb 13, 2009 | 1992 Honda Accord

Not finding what you are looking for?
1992 Honda Accord Logo

1,154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...