Question about 1993 Toyota Pickup

2 Answers

Remove transmission 93 toyota pick up

I am replacing the clutch in my 93 toyota pick up and don't see a way to get to the top two bolts on the bell housing. What is the best way to do this without removing half the engine.

Posted by on

  • murphy_sk Feb 13, 2009

    I have the cross member out and its not moving. Do you have to loosen the motor mounts to get the trans to come down to get to the top bolts?

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,596 Answers

I Normaly use A 36" Extention w/ Swivel Socket, Or Lieve Side Bolts In And Drop Cross Member to Lower Rear of Trans to Gain Exess to TOP Bell Bolts one or BOTH Together Should Do the TRICK. Let Me Know!! And Please Dont forget to Rate me , Thank You Much !!

Posted on Feb 13, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,976 Answers

You'll have to disconnect the cross member that holds everything in. Jack it (the motor) up first or it will fall out faster than you ever imagined.

Posted on Feb 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the 5sp transmission from my 2003 toyota celica gt


You need a lift, a hanger to hold the engine from the top a transmission jack and about 5 hrs.Disconnect battery. hang the engine from the support hanger. Remove front wheels. loosen and remove axle nuts. Loosen spindles and disconnect tie rod ends. Disconnect ABS sensors. Remove the axles. Disconnect everything from the subframe if equipped. Disconnect the transmission mount and drop the engine down to access the bell housing bolts. Remove bolts, after disconnecting all electrical and clutch controls. Support the transmission with a jack and remove. Reverse process to install.

Oct 20, 2014 | Toyota Celica Cars & Trucks

1 Answer

How do i drop the trans


Remove the Rear Drive Shaft
Remove the Transfer case if 4x4
Disconnect the Shift
Disconnect the Clutch Secondary
Floor Jack under the Transmission
Remove the Cross Member
Remove Bell House Bolts
Pull straight Back
Lower Down
6 Pressure Plate Bolts
Remove 6 Flywheel Bolts

*(Recommend replacing Rear Main Seal)

Resurface Flywheel
Reassemble

Apr 15, 2013 | 1991 Ford F250

1 Answer

How to replace clutch step by step on a toyota rav4 4wd


You need some very specialized tools to do that You'll need a jack to hold the transfer case once you remove all the bolts holding it to the transmission. Remove the drive shafts.Then you'll need to remove the transmission, again with a supporting jack. Once that has been accomplished , remove the bolts holding the clutch to the flywheel. I'd replace the pilot bearing in the flywheel that holds the input shaft to the gearbox before proceeding. There are special tools available to do that. Now assemble the clutch disk and the clutch plate and put the bolts back in without tightening them. Now take the clutch alignment tool and push it thru the clutch disk and into the new pilot bearing. position it so the clutch disk is dead center in the clutch plate and then finish tightening the bolts Put a new throw out bearing on the clutch release lever and reinstall the transmission and transfer case. Reinstall the drive shafts and replace any gear oil that may have spilled out of the transmission or transfer case. Adjust the clutch pedal clearance to spec and you're done.

Mar 30, 2013 | 1996 Toyota RAV4

1 Answer

I'm removing and planning to rebuild my 93 land


It is actually easier to pull them both because of the top bellhousing bolts and the tourqe converter bolts.

Jun 05, 2011 | 1993 Toyota Land Cruiser

1 Answer

Does a 1995 toyota tercel manual transmission or clutch have a filter, transmission slips when i exelerate. manualtransmission


If this is a manual transmission and you get slippage at acceleration, then your clutch is slipping.

An adjustment might help a little bit, for a while, but I think I'd prepare myself for having the transmission pulled and the clutch replaced.

The clutch assembly is made up of 4 main elements: (1) the flywheel (bolted to the rear end of the engine crankshaft), (2) the pressure plate bolted to the flywheel (a spring loaded device that applies pressure to the clutch disc), (3) the clutch disc (sandwiched between the flywheel and pressure plate) that connects, via friction, the engine to the transmission, (4) the throw out bearing, which pushes against the fingers of the pressure plate to release the clutch disc engagement.

I'd seriously consider having some one do this for you....having to remove the transmission is not something for the faint of heart. Serious injury could result if the transmission were to fall on you while pulled back from the engine bell housing.

Oh, and another thing...I'd replace the pilot shaft bushing while I was in there.

If you really want to do this yourself, then go to your local auto parts store and purchase a vehicle specific repair manual. It should outline the steps specific to your car.

Remember....be very careful!

Mar 02, 2011 | 1995 Toyota Tercel

1 Answer

Change transmission instructions


this is for rear wheel drive only front wheel drives require removing axle shat and dropping tie rod end and lower ball joint to get tranny out. If you start this I will give tork setting when I know what you have as it is a lot of work to type this out.

First disconnect the battery, inside the cab pull shifter boot off and remove snap ring to remove shifter, next get a block to go under engine remove drive line bolts and be sure E-brake is set and block the wheels, next put bolts from driveline into the read differential in order so you will be able to find them next disconnect the two starter bolts from the starter and tie starter up as not to allow the starter weight to hang on the wires. Remove two bolts holding slave cylinder on let hang off the side do not lose the shaft out of slave. Next remove the transmission mount bolt out next pull four bolts out of transmission cross member, next remove 5 bolts out of bell housing now get a baggie and a couple of rubber bands and pull drive shaft slide baggie over the transmission tail shaft and put on rubber band on bag to keep from losing fluid move drive shaft out of the way. Next disconnect the Speedo cable and wiring harness the reverse switch is at the top so will have to drop the tranny down to keep from breaking wire. Once you have a gap between the transmission and engine put block under back of engine slide the transmission out let the front drop down then lift up on rear of transmission and slide the cross member out of the way. Next slide tranny out of the way next remove the 6 bolts on the clutch assembly turning each bolt 1 and a ½ turns each till clutch is loose remove the clutch pressure plate and the throw out bearing, remove flywheel take to machine shop and have surfaced, replace the clutch plate pressure plate and the throw out bearing reinstall in reverse if you see any oil leaks replace seals, also replace rear transmission seal now if you don’t it will leak next after it is back together be sure you put new fluid in the transmission and bleed the slave cylinder.

Jun 28, 2009 | Nissan Pickup Cars & Trucks

1 Answer

Need help fitting a clutch on a VW GTI Golf


undo centre wheel hub nut 30mm/32mm, socket. undo lower wish-bone outer bolts, disconect battery,/remove starter motor,/remove transmission mounting bolts to body frame ,/ remove all surrounding bolts around bell housing transmission,/ remove clutch cable from transmission,/ remove drive shafts from centre hub and transmission,/ make sure car is standing on axle stands at front of jacking points,/use a trolley jack to suport engine sump with a piece of wood,/ slide transmission away from flywheel,/lower transmision on floor,/undo all clutch plate preasure bolts 10mm,/remove thrust bearing located on centre transmision shaft ,.also make sure if fitted speedo cable needs to be removed.new clutch plate should indicate flywheel ,without fitting clutch plate wrong way round/otherwise transmision will not bolt to engine block.,

May 17, 2009 | 1999 Volkswagen GTI

1 Answer

Changing the clutch in an 87 toyo p/u


  • drive shaft - 4
  • wiith carrier br g-6
  • crossmember2-4 removal from trans
  • clutch slave cylinder -2
  • trans to bell housing -4
  • Shifter- floor screws -4
  • shift stick - Under boot press down and rotate stick retainer cup
  • Safety, ease of removal and damage prevention to engine components: SUPPORT REAR OF ENGINE.
  • clutch pressure plat -6
  • clutch pilot bushing - bronze- split w/small chisel- must replace- tap new bushinG into clean hole - lube with light amout of grease
  • Clutch release brg. replace and properly situate on fork and retainers
  • Note! check clutch disc for proper spline match with trans input shaft.
  • Note, Use clutch pilot tool (Parts store available) to center clutch disc while tightening pressure plate.
  • Check trans fluid level after assemby is complete. Good luck.FORCE NOTHING

May 06, 2009 | 1987 Toyota Pickup

1 Answer

Need clutch replacement directions for Ford Ranger


Remove drive shaft,remove crossmember under transmission.Remove transmission and diconnect linkage.Remove bell housing,and clutch berring assembely.Remove bolts on pressure plate.Once this is done.Remove fly wheel for machineing.you will need a pilot shaft to alighn clutch assemblely.Possible one will come with new clutch and pressure plate.Reverse assemblely in same order remember to torque all your bolts with torque wrench.Take your time.

Apr 19, 2009 | 1994 Ford Ranger Supercab

1 Answer

Need Directions to Replace clutch in a1993 5spd.toyota 4runnerV6


start off bt taking off your shifter, then disconnect the wires,cables, and the 4x4 linkage, the drop out both drive shafts, support the tranny and transfer case then remove the tranny mount. take out the bolts on the bell housing that go into the motor the pull out the slave cylinder,and the last thing to remove is the cross member that holds up your tranny. after that slide the tranny back about 6 inches tor until it's free from the block and lower it down. after you get it on the ground pull of out clutch fork that is in the bell housing of your tranny, pull the bearing off the shaft that is in the bell housing as well. and last but not least take off the clutch plate ans the clutch disk that is on the fly wheel on your block. and i cant stress this enough be careful when you pull the tranny out and make sure it will not fall on you. so please do it carefully. And take your time.

Mar 26, 2009 | 1993 Toyota 4Runner

Not finding what you are looking for?
1993 Toyota Pickup Logo

728 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...