I bought a new axle boot kit but when our mechanic begun to repair it, he doesn't know how to remove the velocity joint. It must be remove first before replacing a new axle boot kit. Please give me instruction. A step by step on how to replace the axle boot kit. There are some parts if we force to remove it, we might broke the velocity. Here in our place, there is no mercedez benz center. We only hire auto mechanic. But the problem is they're not familiar. We need your help. Please.
An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert whose answer got voted for 20 times.
An expert who has answered 20 questions.
Re: how to remove the velocity joint?
Hi, on the CV where the shaft goes into the joint there is a circlip you hace to open the clip and tap the joint at the same time to remove it, they can be a pain but thats how to get it off, refit is just put the joint on the lead of the shaft and tap it home, do not hit the threads without protecting them ie use a block of wood and hammer the wood not the joint, hope this helps you,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
get a boot replacement kit remove axle from suspension and trans. clean old grease out of failed axle, stuff new grease into cv joint and put new boot on shaft close to joint. fill the boot with the rest of the tube of cv grease and install per instructions.
YOU CAN GET A BOOT REPAIR KIT OR A ZIP BOOT.DO NOT LIKE ZIP BOOT,DOESNT WORK . BEST TO GET A REMANUFACTURED AXLE AND REPLACE AS A UNIT,DOESNT COST MUCH MORE AND WIL WORK WITH A WARRANTY.TAKE OFF WHEEL,LOOSEN AXLE NUT,TAKE OFF LOWER BALL JOINT,POP AXLE WITH HAMMER TO DRIVE AVLE OUT OF BEARING A LITTLE WAYS THEN PUILL UP ON STRUT ASSEMBLY TO GET AXLE ALL THE WAY OUT OF BEARING/HUB ASSEMBLT. POP OUT AXLE ANT HE SLIDE IN THE NEW UNIT
ITS NOT A HARD JOB TO DO BUT YOU NEED TOOLS LIKE TIE ROD END REMOVING TOOL,YOU NEED SHAP RING PLIERS,YOU NEED HYDRALIC JACK AND AXLE NUT SOCKET 1/2 BREAKER BAR AND A TORQUE WRENCH RANGES TO 200 FT LBS YOU WILL NEED REPAIR MANUAL FOR TORQUE SPECS.THE ,MANUAL WILL SHOW AND TELL YOU HOW TO REMOVE FRONT AXLE SHAFT CV JOINTS.IT WILL LOT CHEAPER TO BUY WHOLE FRONT AXLE WITH NEW CV JOINTS.YOU NEED CV JOINT BOOT CLAMP TOOL AND ITS A WHOLE LOT OF CLEANING INVOLVE PLUS PACKING NEW BEARINGS WITH GREASE.ITS MORE OF HEAD ACHE BEST TO BUY NEW ONE.
Well to start with it is a CV (constant velocity) joint.
You might have the option if the joint is not "OUT" of installing a new boot on the joint without removing it from the vehicle.
If it is out the you have to remove the tire from the side that is out.
Take off the nut that is on the end of the axle.
Then remove the spindle from the lower a frame.
Pull the spindle off the outer splines of the axle shaft
Then with a bar pop the old one out of the transmission and reverse the procedure it go back together. Make sure you get the axle popped back in the transmission.
"Make sure you get the correct replacement axle"
There are no instructions available except with the purchase of SOME boot kits. Depending on the CV joint design, you may not be able to remove the joint from the axle. However, most Hyundai CV joints can be removed from the axle by using a drift and a 2 pound hammer to knock the joint off the axle. Once you've done this, it's a simple matter of removing the old boot and installing the new one w/fresh grease and tension bands. Otherwise, you have to remove the DOJ from the other end of the axle and replace the boot that way.
Hello, If the axle shafts have not been replaced before, you have the old style c/v joints. The tools to do this job are very expensive abd are usually only purchased by dealers etc. They consist of a large cutter, looks like a huge pipe cutter, and a crimper, to crush the cans together. You would be better served to buy an updated axle shaft assembly that is made so anyone can replace the boots. I case you were not sure how to remove the axles, here it is. To do this, you need to elevate the car securely, remove the wheels,
remove the long 13mm bolt from inside the hub then place jack under the
differential and unbolt the mount from the frame, let the diff down
remove cover, remove "C" clip from the end of the axle, jack the diff
up as high as you can get it, take axle down from the wheel side, and
then slide the axle out of the diff. Then you slide the boot down and
at the end of the axle you will find a snap ring. remove snap ring and
then tap the c/v joint out. If you find this information to be correct would you please enter a "fixya" rating. Thanks, Gator241