Question about 2001 Hyundai Santa Fe

2 Answers

Location of the coolant temperature sensor

Check engine code indicates a faulty coolant temperature sensor, the engine runs rough and hard to start. Plan to replace the sensor, where is the general location?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 333 Answers

You will find this sensor where the fat hos comes from the radiator and conects to the engine block. It would be on the housing where the thermostat is located. If it is not there you should look for a sensor that has a wire connected to it anywhere on the engine block where a water inlet is located. I hope this helps. Don't forget to rate my answer, thanks.

Posted on Feb 13, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

In the top of the intake very small hard to see

Posted on Feb 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2008 PT Cruiser; getting P0128 code; I've changed thermostat & temperature sensor; I have to fill the anti-freeze container every 2 weeks; temperature hand will not always be at half way point. ...


This means that the engine's PCM detected that the engine has not reached the required temperature level within a specified amount of time after starting the engine. The intent of the P0128 code is to indicate a faulty thermostat. In determining the engine did not reach a "normal" temperature, it takes into account the length of time the vehicle has been running, the intake air temperature (IAT) sensor reading, the engine coolant temperature (ECT) sensor reading, and the speed of the vehicle.
A code P0128 may mean that one or more of the following has happened:
  • Low engine coolant level
  • Leaking or stuck open thermostat
  • Faulty cooling fan (running too much)
  • Faulty coolant temperature (ECT) sensor
  • Faulty intake air temperature (IAT) sensor
Past experience indicates that the most likely solution is to replace the thermostat. However here are some suggestions on troubleshooting and repairing a P0128 OBD-II code:
  • Verify coolant strength & level
  • Verify proper cooling fan operation (check if it's running more than it should). Replace if necessary.
  • Verify proper engine coolant temperature (ECT) sensor operation, replace if necessary.
  • Verify proper intake air temperature (IAT) sensor operation, replace if necessary.
  • If the above items check out good, replace the thermostat
you have all ready replaced the thermostat with the proper temperature opening thermostat(hopefully) and coolant sensor, you say you have to refill the coolant every 2 weeks this indicates that you either have a coolant leak that needs to be checked out and repaired or you are burning coolant which indicates a possible head gasket problem which will have to be checked. a low coolant level will set this code as there is not enough coolant in the engine to get the engine to operating temperature and stay there. these last suggestions is where I would start to look.

Sep 24, 2014 | 2008 Chrysler Pt Cruiser

1 Answer

Codes p0128


A code P0128 may mean that one or more of the following has happened: Low engine coolant level Leaking or stuck open thermostat Faulty cooling fan (running too much) Faulty coolant temperature (ECT) sensor Faulty intake air temperature (IAT) sensor Possible Solutions Past experience indicates that the most likely solution is to replace the thermostat. However here are some suggestions on troubleshooting and repairing a P0128 OBD-II code: Verify coolant strength & level Verify proper cooling fan operation (check if it's running more than it should). Replace if necessary. Verify proper engine coolant temperature (ECT) sensor operation, replace if necessary. Verify proper intake air temperature (IAT) sensor operation, replace if necessary. If the above items check out good, replace the thermostat

Aug 09, 2014 | 2007 Pontiac G6 GT Convertible

1 Answer

2004 trailblazer code po128


P0128:
P0128 OBD-II Trouble Code
Technical DescriptionCoolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

What does that mean?This means that the engine's PCM detected that the engine has not reached the required temperature level within a specified amount of time after starting the engine. The intent of the P0128 code is to indicate a faulty thermostat. Similar codes: P0125

In determining the engine did not reach a "normal" temperature, it takes into account the length of time the vehicle has been running, the intake air temperature (IAT) sensor reading, the engine coolant temperature (ECT) sensor reading, and the speed of the vehicle.

CausesA code P0128 may mean that one or more of the following has happened:

Low engine coolant level .
Leaking or stuck open thermostat .
Faulty cooling fan (running too much) .
Faulty coolant temperature (ECT) sensor.
Faulty intake air temperature (IAT) sensor .Here's a link on replacing your thermostat.

Feb 06, 2013 | 2004 Chevrolet TrailBlazer

1 Answer

I went to scan my toyota yaris car and the following codes were give ; temperature ckt low input po117


EOBD II Error Code: P0117
Fault Location:
Engine Coolant Temperature (ECT) Sensor (G62) - Low Input
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
Coolant thermostat.
Wiring short to earth.
Engine coolant temperature (ECT) sensor.

EOBD II Error Code: P0340
Fault Location:
Camshaft Position (CMP) Sensor A (G40), Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Wiring from/to Camshaft Position Sensor (CMP) faulty.
Camshaft position (CMP) sensor faulty.
Timing misaligned.
Possible Solutions:
Check Wiring from/to Camshaft Position Sensor.
Check Camshaft Position Sensor.
Check Timing.

EOBD II Error Code: P0500
Fault Location:
Vehicle Speed Sensor (VSS) - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Non Emission Fault - No warning light.
Wiring.
Vehicle speed sensor (VSS).
Engine control module (ECM).

Dec 13, 2012 | 2001 Toyota Yaris

3 Answers

P0128 (and P0116) on 2006 GMC Sierra v-8, 5.3L, 4x4. Originally getting low temp readings on guage. After replacing the thermostat, the problem seemed to be fixed. A few days later, I was getting my...


P0116 - Engine Coolant Temperature (ECT) Circuit Range/Performance Problem
The ECT (Engine coolant temperature) sensor is a thermistor which changes resistance based on temperature of the coolant in contact with it. The ECT sensor will be located in the block or coolant passage. Usually it is a two wire sensor. One wire is a 5 Volt supply from the PCM (Powertrain Control Module) to the ECT. The other is a ground to the ECT.

As the temperature of the coolant changes the resistance on the signal wire changes accordingly. The PCM monitors the reading and determines coolant temperature in order to perform essential engine fuel management. When engine coolant is low, sensor resistance is high. The PCM will see a high signal voltage (low temperature). When coolant is warm, the sensor's resistance is low and the PCM will see a high temperature. The PCM expects to see slow resistance changes on the ECT signal circuit. If it sees a quick change in voltage that isn't consistent with an engine warming up, this P0116 code will set. Or if it sees a lack of change in ECT signal, this code may set.

Symptoms: There may be no noticeable symptoms if the problem is very intermittent, however the following may occur:
MIL (Malfunction Indicator Lamp) illumination
Poor drivability
Black smoke at tailpipe
Poor fuel economy
May not idle
May exhibit stalling or misfires

Causes: Potential causes of the P0116 code include:
Missing or stuck-open thermostat
Bad ECT sensor
Short or open on signal wire
Short or open on ground wire
Poor connections in wiring

Possible Solutions: If there are any other ECT sensor codes, diagnose them first.
Using a scan tool, check the ECT reading. On a cold engine, it should match the IAT reading or should be equal to ambient (outside) temperature reading. If it does match the IAT or ambient temp, check the freeze frame data on your scan tool (if equipped). The saved data should tell you what the ECT reading was when the fault occurred.

a) If the saved info indicates that the engine coolant reading was at the coldest exreme (around -30 deg. F) then that's a good indication the ECT resistance was intermittently high (unless you live in Anchorage!) Check for an open in the ECT sensor ground and signal circuits and repair as necessary. If they appear okay, warm the engine up while monitoring the ECT for any intermittent jumps high or low. If there are replace the ECT.

b) If the saved info indicates that the engine coolant reading was at the warmest exreme (around 250+ deg.F) then that's a good indication the ECT resistance was intermittently low. Check for a short to ground on the signal circuit and repair as necessary. If it appears okay, warm the engine up while monitoring the ECT for any intermittent jumps high or low. If there are replace the ECT.

Other ECT sensor and circuit related DTCs: P0115, P0117, P0118, P0119, P0125, P0128
--------------------------------------------------------------------------------------------------------------------

P0128 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
This means that the engine's PCM detected that the engine has not reached the required temperature level within a specified amount of time after starting the engine. The intent of the P0128 code is to indicate a faulty thermostat. Similar codes: P0125

In determining the engine did not reach a "normal" temperature, it takes into account the length of time the vehicle has been running, the intake air temperature (IAT) sensor reading, the engine coolant temperature (ECT) sensor reading, and the speed of the vehicle.

Symptoms: You will likely not notice any drivability problems other than the MIL illumination.

Causes: A code P0128 may mean that one or more of the following has happened:
Low engine coolant level
Leaking or stuck open thermostat
Faulty cooling fan (running too much)
Faulty coolant temperature (ECT) sensor
Faulty intake air temperature (IAT) sensor

Possible Solutions: Past experience indicates that the most likely solution is to replace the thermostat. However here are some suggestions on troubleshooting and repairing a P0128 OBD-II code:
Verify coolant strength & level
Verify proper cooling fan operation (check if it's running more than it should). Replace if necessary.
Verify proper engine coolant temperature (ECT) sensor operation, replace if necessary.
Verify proper intake air temperature (IAT) sensor operation, replace if necessary.
If the above items check out good, replace the thermostat
If Nissan vehicle, check for Technical Service Bulletins (TSBs), as the ECM may need to be reprogrammed to correct the P0128 code



These codes are telling you that the engine temperature is not sufficient. This can be caused by a faulty coolant sensor,air in the cooling system,or a faulty computer.
The engine should run at 190 F & higher when warmed up. Scan the computer system to view engine temperature.

Keep us updated.

Oct 01, 2011 | 2006 GMC Sierra

2 Answers

Eror code: PO128 Code


This means that the engine's PCM detected that the engine has not reached the required temperature level within a specified amount of time after starting the engine. The intent of the P0128 code is to indicate a faulty thermostat. Similar codes: P0125
In determining the engine did not reach a "normal" temperature, it takes into account the length of time the vehicle has been running, the intake air temperature (IAT) sensor reading, the engine coolant temperature (ECT) sensor reading, and the speed of the vehicle.
Symptoms You will likely not notice any drivability problems other than the MIL illumination.
Causes A code P0128 may mean that one or more of the following has happened:
  • Low engine coolant level
  • Leaking or stuck open thermostat
  • Faulty cooling fan (running too much)
  • Faulty coolant temperature (ECT) sensor
  • Faulty intake air temperature (IAT) sensor
Possible Solutions Past experience indicates that the most likely solution is to replace the thermostat. However here are some suggestions on troubleshooting and repairing a P0128 OBD-II code:
  • Verify coolant strength & level
  • Verify proper cooling fan operation (check if it's running more than it should). Replace if necessary.
  • Verify proper engine coolant temperature (ECT) sensor operation, replace if necessary.
  • Verify proper intake air temperature (IAT) sensor operation, replace if necessary.
  • If the above items check out good, replace the thermostat
  • If Nissan vehicle, check for Technical Service Bulletins (TSBs), as the ECM may need to be reprogrammed to correct the P0128 code
Other ECT sensor and circuit related DTCs: P0115, P0116, P0117, P0118, P0119, P0125

Feb 08, 2011 | Buick Rendezvous Cars & Trucks

1 Answer

I have a 2004 Chevy Impala. As I was driving home yesterday I had the heater on full blast - temp outside appx. 60. The check engine light came on and I had a P0128 code. Could this be due to keeping...


This means that the engine's PCM detected that the engine has not reached the required temperature level within a specified amount of time after starting the engine. The intent of the P0128 code is to indicate a faulty thermostat. Similar codes: P0125

In determining the engine did not reach a "normal" temperature, it takes into account the length of time the vehicle has been running, the intake air temperature (IAT) sensor reading, the engine coolant temperature (ECT) sensor reading, and the speed of the vehicle.


A code P0128 may mean that one or more of the following has happened:

  • Low engine coolant level
  • Leaking or stuck open thermostat
  • Faulty cooling fan (running too much)
  • Faulty coolant temperature (ECT) sensor
  • Faulty intake air temperature (IAT) sensor

Past experience indicates that the most likely solution is to replace the thermostat. However here are some suggestions on troubleshooting and repairing a P0128 OBD-II code:

  • Verify coolant strength & level
  • Verify proper cooling fan operation (check if it's running more than it should). Replace if necessary.
  • Verify proper engine coolant temperature (ECT) sensor operation, replace if necessary.
  • Verify proper intake air temperature (IAT) sensor operation, replace if necessary.
  • If the above items check out good, replace the thermostat


REFERENCE: http://www.obd-codes.com/p0128


I hope this helps a bit!

Jan 11, 2011 | 2002 Chevrolet Venture Passanger

1 Answer

Error code po128


P0128 - Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

This means that the engine's PCM detected that the engine has not reached the required temperature level within a specified amount of time after starting the engine. The intent of the P0128 code is to indicate a faulty thermostat. Similar codes: P0125

In determining the engine did not reach a "normal" temperature, it takes into account the length of time the vehicle has been running, the intake air temperature (IAT) sensor reading, the engine coolant temperature (ECT) sensor reading, and the speed of the vehicle.

Symptoms: You will likely not notice any drivability problems other than the MIL illumination.

Causes: A code P0128 may mean that one or more of the following has happened:
* Low engine coolant level
* Leaking or stuck open thermostat
* Faulty cooling fan (running too much)
* Faulty coolant temperature (ECT) sensor
* Faulty intake air temperature (IAT) sensor

Possible Solutions: Past experience indicates that the most likely solution is to replace the thermostat. However here are some suggestions on troubleshooting and repairing a P0128 OBD-II code:
* Verify coolant strength & level
* Verify proper cooling fan operation (check if it's running more than it should). Replace if necessary.
* Verify proper engine coolant temperature (ECT) sensor operation, replace if necessary.
* Verify proper intake air temperature (IAT) sensor operation, replace if necessary.
* If the above items check out good, replace the thermostat
* If Nissan vehicle, check for Technical Service Bulletins (TSBs), as the ECM may need to be reprogrammed to correct the P0128 code


Hope helps (remember to rate this answer).

Jan 07, 2011 | 2002 Chevrolet Venture Passanger

2 Answers

P0128 coolant temp below thermostat/regulating temp


P0128 - Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

This means that the engine's PCM detected that the engine has not reached the required temperature level within a specified amount of time after starting the engine. The intent of the P0128 code is to indicate a faulty thermostat. Similar codes: P0125

In determining the engine did not reach a "normal" temperature, it takes into account the length of time the vehicle has been running, the intake air temperature (IAT) sensor reading, the engine coolant temperature (ECT) sensor reading, and the speed of the vehicle.

Symptoms: You will likely not notice any drivability problems other than the MIL illumination.

Causes: A code P0128 may mean that one or more of the following has happened:
* Low engine coolant level
* Leaking or stuck open thermostat
* Faulty cooling fan (running too much)
* Faulty coolant temperature (ECT) sensor
* Faulty intake air temperature (IAT) sensor

Possible Solutions: Past experience indicates that the most likely solution is to replace the thermostat. However here are some suggestions on troubleshooting and repairing a P0128 OBD-II code:
* Verify coolant strength & level
* Verify proper cooling fan operation (check if it's running more than it should). Replace if necessary.
* Verify proper engine coolant temperature (ECT) sensor operation, replace if necessary.
* Verify proper intake air temperature (IAT) sensor operation, replace if necessary.
* If the above items check out good, replace the thermostat
* If Nissan vehicle, check for Technical Service Bulletins (TSBs), as the ECM may need to be reprogrammed to correct the P0128 code

Hope helps (remember to rate and comment this).

Sep 27, 2010 | 2006 Dodge Caravan

1 Answer

Dtcdescriptionp0128andrepair


DTC P0128 - Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

What does that mean?
This means that the engine's PCM detected that the engine has not reached the required temperature level within a specified amount of time after starting the engine. The intent of the P0128 code is to indicate a faulty thermostat. Similar codes: P0125

In determining the engine did not reach a "normal" temperature, it takes into account the length of time the vehicle has been running, the intake air temperature (IAT) sensor reading, the engine coolant temperature (ECT) sensor reading, and the speed of the vehicle.

Symptoms:
You will likely not notice any drivability problems other than the MIL illumination.

Causes:
A code P0128 may mean that one or more of the following has happened:
* Low engine coolant level
* Leaking or stuck open thermostat
* Faulty cooling fan (running too much)
* Faulty coolant temperature (ECT) sensor
* Faulty intake air temperature (IAT) sensor

Possible Solutions:
Past experience indicates that the most likely solution is to replace the thermostat. However here are some suggestions on troubleshooting and repairing a P0128 OBD-II code:
* Verify coolant strength & level
* Verify proper cooling fan operation (check if it's running more than it should). Replace if necessary.
* Verify proper engine coolant temperature (ECT) sensor operation, replace if necessary.
* Verify proper intake air temperature (IAT) sensor operation, replace if necessary.
* If the above items check out good, replace the thermostat
* If Nissan vehicle, check for a TSB such as this one. The ECM may need to be reprogrammed to correct the P0128 code


Hope helps (remember rated this).

Jul 01, 2010 | 2004 GMC Envoy

Not finding what you are looking for?
2001 Hyundai Santa Fe Logo

1,170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...