Question about 2004 GMC Envoy

Open Question

Jack placement for tire changing

I am changing the right rear tire where do I safely place the jack?

Posted by on

  • yadayada
    yadayada May 11, 2010

    what kind of jack?

×

6 Suggested Answers

  • 1 Answer

SOURCE: Jack Location for Tire Change

under the back seats, jack is under the driver's side backseat, tire iron & rods are under passenger's side backseat.

Posted on Aug 24, 2008

ogre1967
  • 16 Answers

SOURCE: Low spare fault in a 2005 Jeep Liberty, tire is at rated pressure.

Wow another great problem by a dodge product i would check for a recall on the sensor switch

Posted on Nov 05, 2008

  • 65 Answers

SOURCE: where do I put jack when changing rear tire

Put on e-brake and place jack under rear axle on the side of the wheel as close to it as you can

Posted on Nov 27, 2008

cranegang
  • 21 Answers

SOURCE: where to i place the jack when changing a tire on a 2000 ddg dura

If you have the owners manual it will say where to exactly place the jack. If not one can be picked up at a junk yard for a couple of dollars. One thing they probably won't tell you in the owners manual is that when removing the tire to never put your hands at the 6 and 12 o'clock positions on the tire. I don't mean to scare you, but this is very dangerous due to the fact that if the vehicle slips off the jack your hands could get crushed either between the fender and the tire and/or between the tire and the ground. Always put your hands in the 3 and 9 o'clock positions on the tire when removing. And never crawl under the vehicle with the factory jack.
Hope this helps.

Posted on Jan 19, 2009

  • 3 Answers

SOURCE: jack position to change rear tire 98 pontiac grand prix

factory jack to be placed in front of tire inbetween notches on seem. A manual floor jack can be used placing it under center connection bracket for rear wheels. Be shure to block front tires when using floor jack and have car in gear if a manual or park if automatic transmision.

Posted on Mar 31, 2009

yankstorm02
  • 145 Answers

SOURCE: Car won't lower the rear wheel was replaced by a used tire place.

Sometimes you can trick the module by opening all the doors,turning on the air ride switch and starting the car. Let it run for aboout 5 minutes.That should straighten out your ride. Let me know if you need more assistance

Posted on Apr 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jack placement for rear tire change? This seems the most sensible place, but it isn't lifting enough.


Looks like that would be OK. Can you lower it again and put a block of wood under the jack? Those jacks also work on the axle if it is rear wheel drive. Or maybe there is room to put the jack under the spring support right beside the wheel? I have been in a similar pinch before, where it would not raise enough. I used one jack to raise as far as it could, then used another jack in a second location to raise the wheel higher. There is always a way. First try a block under that jack.

Jun 29, 2015 | Cars & Trucks

1 Answer

Placement of jack to change the front driver side tire


There is a notch location just about below front fender. It is a gap in the downward protruding flange that will be the size of the top of the jack. Set parking brake and chock or block rear wheels if possible to prevent vehicle moving and avoid injury.

Jan 07, 2014 | 1994 Buick Roadmaster

1 Answer

Where do you place the jack when the front passenger tire needs changing?


Best placement for the jack is under the axle tube as close to the wheel as possible without interfering with any brackets etc. Same applies to rear if you ever need to do that.

Apr 03, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

How do i rotate tires on a 2008 saturn outlook


you lift the car up on jacks so that the tires are off the ground, then you put jack stands in placement. then you loosen ONLY THE BOLTS ON THE TIRE IN THE AIR remove the tire let the car down on to the jack stands, and move the jack to the next and do the same what you do is take the passenger side back tire and switch it with the drivers side front tire. then you take the drivers side back tire and switch it with the passenger side front tire. make sure the bolts are tight as you can get them then you are done. i hope this information helps. Be careful and drive safe!

Feb 27, 2011 | Saturn Outlook Cars & Trucks

3 Answers

Where do I jack the car up to change right front tire


on the pinch lip on the unibody frame. you should see a notch or something like that.

Jan 07, 2011 | 2003 Toyota Corolla

1 Answer

What is the best location to position a floor jack on 1994 Buick Roadmaster?


Look under the side of the car about 6 inches from the wheel wheel (always between front/rear tires). There is usually a seam of sheet metal joints along the bottom and a 1 or 2 inch notch is cut to allow jack placement (if using factory jack for changing tires).

This is a heavy car, do not work under the car when using the light weight jack that came with the car. Also, do not use cinder blocks (bricks) to support the car if your are going under the car. Use only high quality jack stands on a level surface and place chucks under any wheels still on the ground to prevent rolling.

Be careful!

Please rate me. Thanks!

Nov 19, 2009 | 1994 Buick Roadmaster

2 Answers

Where to place jack to change tire - 2006 Monte


There is a thin piece of metal that runs along the main portion of the car. Place jack on that thin metal that sticks down. On some models there are two tabs that stick down farther on the pinch weld "thin piece of meatal that sticks down." If the vechile have those two tabs the jack goes between them.

Sep 13, 2009 | 2006 Chevrolet Monte Carlo

1 Answer

Jack position to change rear tire 98 pontiac grand prix


factory jack to be placed in front of tire inbetween notches on seem. A manual floor jack can be used placing it under center connection bracket for rear wheels. Be shure to block front tires when using floor jack and have car in gear if a manual or park if automatic transmision.

Mar 31, 2009 | 2002 Pontiac Grand Prix

1 Answer

Where do I put jack when changing rear tire


Put on e-brake and place jack under rear axle on the side of the wheel as close to it as you can

Nov 27, 2008 | 1999 Ford Ranger SuperCab

1 Answer

Jack stand


jack stands most times are placed under neath the axles however in your case the stands should be placed behind the front wheels on the spot where you whould place a regular jack if let's say you were changing a tire. if your working on the rear of the vehical you should put them under each side of rear axle.

Aug 27, 2008 | 1999 Pontiac Sunfire

Not finding what you are looking for?
2004 GMC Envoy Logo

Related Topics:

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...