Question about 2005 Chevrolet Express

1 Answer

2005 chevy express van where is Headlight adjustments

Where is the adjustment for the headlights? I need to lower the aim.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 152 Answers

Here is a link to a repair guide for your vehice that will help you with the headlights along with any other thing you might need.
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800b4a31

Posted on Feb 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just bought a used 05 subaru impreza. Noticed the right head lamp is pointed too high. where is the adjustment screws to lower the lamp. It seems great on the horizontal just needs to be adjusted on the...


I hope this info helps!

ADJUSTMENT

HEADLIGHT AIMING

CAUTION: Turn off the light before adjusting headlight aiming. If the light is necessary to check aiming, do not turn on for more than 2 minutes.


  1. Before checking the headlight aiming, be sure of the following:
    • The area around the headlight has not sustained any accident, damage or other type of deformation.
    • Vehicle is parked on level ground.
    • The inflation pressure of tires is correct.
    • Vehicles gas tank is fully charged.
    • Bounce the vehicle several times to normalize the suspension.
    • Make certain that someone is seated in the driver s seat. Turn the headlights on and then adjust the low beam pattern to the following positions on the screen.
  1. Position the headlight beam leveler switch to "0" .
129148368


129148369


129148370



  1. Rotate the adjusting screw (A) to adjust aim.

Aug 01, 2011 | Subaru Impreza Cars & Trucks

1 Answer

How do you aim or adjust 200l legacy headlights


Hello Terry.

HEADLIGHT AIMING



CAUTION: Turn off the light before adjusting headlight aiming. If the light is necessary to check aiming, do not turn on for more than two minutes .
NOTE:
Before checking the headlight aiming, be sure of the following:
  • The area around the headlight has not sustained any accident, damage or other type of deformation.
  • Vehicle is parked on level ground.
  • The inflation pressure of tires is correct.
  • Vehicle's gas tank is fully charged.
  • Bounce the vehicle several times to normalize the suspension.
  • Make certain that someone is seated in the driver's seat.
  1. Place a cloth over the headlight that does not require aiming adjustment.
  2. Turn the headlights on. Perform the aiming adjustment for the other headlight as follows:
kiltylake_66.gif

CAUTION: Do not perform lateral headlight aiming adjustment.There you are, the procedure from Subaru manual.

Hope this helps you.
Thank you for using FixYa.

KL

Dec 04, 2010 | 2001 Subaru Legacy

2 Answers

Lights are too high. The low beams seem to blind oncoming traffic, and the high beams shine too high also.


if you have put bigger tires on the vehicle or lifted it you need to adjust the headlights they sell the tool at any auto parts stores its a small rachet tool you turn to lower the head lights

Feb 12, 2010 | 2003 Chevrolet Express

1 Answer

How do i adjust the head lights on a 1997 grand marquis


AIMING THE HEADLIGHTS

On 1989-91 vehicles, the headlights can be aimed using the adjusting screws located above and to the side of the headlight bulbs. A rough adjustment can be made while shining the headlights on a wall or on the rear of another vehicle, but headlight adjustment should really be made using proper headlight aiming equipment.
On 1992-98 vehicles, the aerodynamically styled headlights necessitate the use of headlight aiming kit 107-00003 or equivalent. The adjustable aimer adapters provided in the kit must be used to aim the headlights. Adjustment aimer adapter positions are moulded into the bottom edge of the headlight lens. Set and lock the adjustable adapters, attach each adapter to its mechanical aimer and aim the headlights according to the instructions in the kit.
Headlight aim adjustment should be made with the fuel tank approximately half full, the vehicle unloaded and the trunk empty, except for the spare tire and jacking equipment. Make sure all tires are inflated to the proper pressure.
The headlights must be properly aimed to provide the best, safest road illumination. The lights should be checked for proper aim and adjusted as necessary. Certain state and local authorities have requirements for headlight aiming; these should be checked before adjustment is made.

CAUTION About once a year, when the headlights are replaced or any time front end work is performed on your vehicle, the headlight should be accurately aimed by a reputable repair shop using the proper equipment. Headlights not properly aimed can make it virtually impossible to see and may blind other drivers on the road, possibly causing an accident. Note that the following procedure is a temporary fix, until you can take your vehicle to a repair shop for a proper adjustment.
Headlight adjustment may be temporarily made using a wall, as described below, or on the rear of another vehicle. When adjusted, the lights should not glare in oncoming car or truck windshields, nor should they illuminate the passenger compartment of vehicles driving in front of you. These adjustments are rough and should always be fine-tuned by a repair shop which is equipped with headlight aiming tools. Improper adjustments may be both dangerous and illegal.
For most of the vehicles covered by this guide, horizontal and vertical aiming of each sealed beam unit is provided by two adjusting screws which move the retaining ring and adjusting plate against the tension of a coil spring. There is no adjustment for focus; this is done during headlight manufacturing.
Because the composite headlight assembly is bolted into position, no adjustment should be necessary or possible. Some applications, however, may be bolted to an adjuster plate or may be retained by adjusting screws. If so, follow this procedure when adjusting the lights, BUT always have the adjustment checked by a reputable shop.
Before removing the headlight bulb or disturbing the headlamp in any way, note the current settings in order to ease headlight adjustment upon reassembly. If the high or low beam setting of the old lamp still works, this can be done using the wall of a garage or a building:
  1. Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall.

See Figure 6


1ad3b8e.jpg
Fig. 6: Example of headlight adjustment screw location for composite headlamps
  1. If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows.
  2. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient.

See Figures 7 and 8


9018da5.jpg
Fig. 7: Low-beam headlight pattern alignment


fa6b141.jpg
Fig. 8: High-beam headlight pattern alignment
  1. If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle.
  2. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall.
  3. Have the headlight adjustment checked as soon as possible by a reputable repair shop.

Hope thats helped (remember rated this) Good luck.

Jan 24, 2010 | 1997 Mercury Grand Marquis

2 Answers

2008 Jeep Grand Cherokee has a headlight aiming problem - the low beams are aimed too high. I cannot find the vertical aiming adjustment screws to fix the problem. Can anyone tell me how to adjust the low...


Hi, i have no idea if this will help you or not, but, on the 1997 grand cherokee, if you look at the headlight itself, look to the outer edge, over the top ontop of the headlight there is a white allen key hole, not sure on the size, this, basically is the up and down adjuster for the headlight, sorry if it doesn't help but i've just had to adjust mine, and thats where it is, the one towards the radiator is the in and out, it pushes or pulls the headlight offcentre

Nov 26, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Adjust the headlight beam on 2002 Subaru Outback


two screws on each headlight control the direction the headlights are aimed. One screw, usually at the top but sometimes below the headlight, adjusts the headlight up and down. The other screw, located to one side, controls the headlight from right to left. Turning the appropriate screw one direction or the other will change the direction the headlight points.
In order to aim your headlights you need to have a flat vertical surface you can aim your headlights at in front of a level surface on which to park the car. If your driveway is level your garage door is the perfect place to aim your headlights.
The tools you will need for this job are simple. Masking tape is used to mark where the headlights are to be aimed and a screwdriver is needed to adjust the headlights. A tape measure will be necessary to measure the distance of the vehicle to the surface you're using to check the aim and to measure the up and down distances from your marks

Nov 09, 2009 | 2002 Subaru Outback

1 Answer

2005 Chevy express van, How do I adjust the headlights?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Jul 02, 2009 | 2005 Chevrolet Express

2 Answers

How do you adjust the headlights in a 2005 Chevy Colorado?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jun 15, 2009 | 2005 Chevrolet Colorado

3 Answers

How do i adjust the headlight beam on my Subaru Forester X MY06 Model


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Apr 26, 2009 | 2006 Subaru Forester

2 Answers

Adjusting headlights on a 2005 ford freestar


hello wwhampton,

open the hood, take a close look at your headlights, if it is a headlight assembly, there are two screws with big plastic heads on the back of the assembly, these are the adjusting screws. one for horizontal adjustment and the other one is for vertical adjustment.

if the headlight is a round or square ordinary bulb, the adjusting screws are located near the bulb itself, these are philips screws. one on the top and one on the side.

a suggestion; when adjusting headlights, face the car to a wall about 5 ft away and adjust the headlight.

tnx 4 using fixya.

drcool

Sep 20, 2008 | 2005 Ford Freestar

Not finding what you are looking for?
2005 Chevrolet Express Logo

1,198 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...