Question about 2006 Cadillac SRX

1 Answer

How to replace front turn light bulb on Caddy SRX 2004?

Seems like the whole front bumper has to go...

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 49 Answers

  1. Open the hood.
  2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
  3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
    1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
    2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
    3. Pull the headlamp assembly out and away from the vehicle
    4. Disconnect the headlamp electrical connector.
    5. Remove the headlamp assembly from the vehicle.
    6. Remove the headlamp bulb cover from the headlamp assembly.
    7. Remove the headlamp bulb socket from the headlamp assembly.
    8. Remove the headlamp bulb.
    9. Remove the side marker bulb socket from the outer side of the headlamp assembly.
    10. Remove the side marker bulb.

Posted on Feb 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 cadillac srx fixing or replacing light bulbs rear license plate


You might be able to access it if you stick your hand up inside the rear of the bumper.

Nov 26, 2015 | 2008 Cadillac Srx

Tip

Change the front turn signal bulb on Cadillac SRX


I have found a short cut for changing the front turn signal bulb
  1. Remove the inner fender well cover and then you can remove the light assemble from underneth and replace the bulb.
  2. The cover is attached with a bunch of push on body clips, pry the button up with a screwdriver and pull out fastner.
  3. Then there are two screws holding the light assembly on the bottom and inner side, it clips into the bumper on the outter side. From there it's pretty simple.
  4. FYI the GE replacement cross reference is wrong it's a Sylvania 3757A LL bulb.

on Dec 02, 2009 | Cadillac SRX Cars & Trucks

1 Answer

How to change front turn signal bulb on 2008 SRX Cadillac


Nope don't need to drop the whole light assembly. I just took the wheel and inner cover off, then the 6 torx screws that hold the light hosing together , replaced the turn signal bulb and good to go!!

Mar 04, 2013 | 2004 Cadillac SRX

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

1 Answer

2006 Cadillac SRX- how to replace front directional light bulbs without dismantalling the whole front bumper cover?


Just remove the air filter housing and the inner right fender plastic pins enough to flex it out of the way...... then you can remove the six torx screws and remove the bulb cover........change the bulb.
spray a little WD40 in the bulb socket first.

Feb 20, 2011 | Cadillac SRX Cars & Trucks

1 Answer

How do u change the front signal bulbs on SRX 2004 with out taking the whole car apart???


Remove the bottom plastic cover along the front grills by pulling the push pins which hold them in place. You can slide the cover out . Remove the plastic cover inside the wheel which is also held by push pins.

When both the covers are out you ca use an 9/32'' wrench to remove the two bolts which hold the whole lamp assembly.You then need a torx driver to remove the six torx screws in the light assembly and you can replace the bulb.

Jan 04, 2011 | 2004 Cadillac SRX

3 Answers

I need to change the left front turn signal bulb on a 2006 Cadillac SRX? Looks difficult. Paul LeMaster


hi Paul

Should be able to open the hood remove plastic headlight cover & pull pins (2) on light assembly whole light assembly will pull out then replace turn signal.

Good luck.

Dec 02, 2009 | 2006 Cadillac SRX

3 Answers

Headlight


Well according to my mitchell manuel you don't have to.here is the procedure.
1. open the hood.
2.Remove the push-pin retainer's that secure the top of the upper facia and grill assembly to the upper tie bar to allow the upper facia and grill assembly to flex forward.
3. remove ther bolt and push-pin retainer that secures the top of the headlight assembly to the upper tie bar.
4. Gently pull the upper facia and grill assembly forward to access the bolt on the inboard side of the headlight assembly
5. Pull the headlamp assembly straight out to disengage the the snap in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the inboard assembly clears the front facia.
6. pull the assembly out and away from the veh.From there you'll be able to access bulbs.
be careful not to touch the bulb with fingers or oil in skin will blow bulb.
Good luck.

Aug 19, 2009 | 2004 Cadillac SRX

4 Answers

Replacing front turn signal bulb on 2006 Cadillac SRX


wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Nov 13, 2008 | 2004 Cadillac SRX

Not finding what you are looking for?
2006 Cadillac SRX Logo

727 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...