Question about 1989 Oldsmobile Cutlass Supreme

1 Answer

Brak lights dont work

Brack lights dont work repaced flashers and brake swich also checked fuses all good hazard swich might damaged cutlass superme coup front weel drive

Posted by on

  • yadayada
    yadayada May 11, 2010

    have u replaced the multifunction switch?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

They is a switch under steerihg wheel that isnt makeing contact which is for the turn signals and emergency flashers is needs to be replaced or try to take some electrical contact cleaner and spray it in where u trun the emergency flashers on push them on and off while spraying this in there then check the brake lights if it dont work then replace the switch not expensive

Posted on Feb 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Turn signals won't light up or flash


Test the arn?s on the light side. If you got juice there . Then replace the hole deal. If you dont get anyrhing. The is your turn anddle stick.

Jul 06, 2015 | 1990 Oldsmobile Cutlass Ciera

3 Answers

1999 ford expedition no brake light no turn signal


Sounds like your multifunction control switch needs replaced. Its location is on your steering colum.

9ad0f03f-26fd-405e-89cb-10b4ae059161.jpg

Feb 14, 2015 | 1999 Ford Expedition

1 Answer

1989 cutlass supreme sl turn lights work but dont blink


CHECK THE HAZARD/FLASHER IN THE FUSE BOX CHECK OWNER MANUAL IF YOU HAVE IT

Aug 19, 2012 | 1989 Oldsmobile Cutlass Supreme

1 Answer

Blinkers dont work


Do the brake lights work? If the brake lights work then you probably need a new turn signal flasher,if not then check that all the bulbs are good,front and rear and check for a blown fuse...

Apr 07, 2011 | 1993 Oldsmobile Cutlass Supreme

1 Answer

My brake, hazard and turn lights dont work, i


well u have two seprate problems the hazards and turn signals have a flasher that needs replacing if the fuse is good on the fuse box marked signals .and there is a brake light switch under the dash board near the brake pedal it has two wires on it check the wires make sure they are connected if so replace the brake light switch

Nov 13, 2009 | 2002 Chevrolet Astro

2 Answers

No brake lights, turn signals, or 4-ways.


Did you actually check the bulbs? I believe your brake lights, signal lights, hazards all use the same bulb for each side.

Your brake lights may be your brake switch just above your brake pedal.
The signals could be your electronic flasher module (EFM) located under the dash near the steering column.
Your hazards may be affected by the EFM, but not likely and the switch for your hazards may be faulty

Sep 10, 2009 | 1998 Chevrolet Blazer

3 Answers

Hazard flashers do not work. Turn signals do. Changed relay. Nothing. Ugh. 1992 oldsmobile cutlass supreme


You changed the hazard flasher or the turn signal flasher? It has two, one for the hazard and one for the turn signals

Aug 31, 2009 | 1992 Oldsmobile Cutlass Supreme

2 Answers

Hazard Lights Won't Work on 96 Taurus


FIRST Check for Blown Fuse Then Locate Flasher Units @ Fuse Block to Determine Wiitch one is Hazard Turn On Key Then Turn Syg. Feel Flashers The One you feel Clicking is For Turn The Other IS Flasher Replace this Flasher unit.

  1. Verify the customer's concern by operating the turn signal/hazard flasher lamp to duplicate the condition.
  2. Inspect to determine if one of the electrical concerns apply: VISUAL INSPECTION CHART Electrical
    • Circuitry open/shorted.
    • Fuse junction panel Fuse:
+ 15 (10 A) + 29 (15 A)
  • Damaged multi-function switch.
  • Miniature bulb burned out.
  • Damaged lamp.
  1. If the inspection reveals obvious concern(s) that can be readily identified, service as required.
  2. If the concern(s) remains after the inspection, determine the symptom(s) and go to the Symptom Chart. See: ProceduresSymptom Chart(s)

Jun 01, 2009 | 1996 Ford Taurus

3 Answers

Brake Lights don't work


I have a 1987 Cutlass Supreme and the brake lights wouldn't work. When I moved the tilt steering to a certain position they worked.

May 25, 2009 | 1987 Oldsmobile Cutlass Supreme

1 Answer

Brake lights stay on 2001 chevy s 10


There is a brake light swich along the brake peddle that need's to be adjusted. Quick and easy fix.

Apr 06, 2009 | 2001 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...