Question about 1992 Buick Regal

1 Answer

92 buick regal missing

My car stopped running. told to try replacing crank sensor. Did. same problem. replaced control module,idol air control car runs now but is missing. notice it most when the converter locks up. also has new plugs and wires.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,118 Answers

May have an injector that is not spraying right or maybe pluged up. Try some injector cleaner.

Posted on Feb 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 2003 buick regal ls stop ideling afer it warms up?


The automatic idle control valve may have stopped working or the control module that operates it.

May 17, 2014 | 2003 Buick Regal

1 Answer

92 buick regal custom 3.1L CODE 43 ON AND CAR CUTS OFF SOMETIMES BUT CRANKS BACK


Sounds like the thermostat needs replaced. You may also want to check you MAF sensor.

Feb 21, 2013 | 1991 Buick Regal

1 Answer

What makes the car die after running for so long


Loss of spark is the common reason on this year of buick, that means you either have a defective Crankshaft position sensor or a defective Ignition control module, either one can cause the symptom. Of the two parts the crankshaft position sensor is the most common failure point, to replace it you must remove the front crank pulley and the harmonic balancer behind that pulley, the crank sensor is behind that and is triggered off the harmonic balancer. You access the pulley through the passenger wheel well, you must remove the plastic or rubber splash guards to access it, you will need some special tools, a harminic balancer pulley puller of course will be required. There is also a special tool needed to set the air gap from the sensor to the pulley, so to get around that tool measure the old sensors air gap with a feeler gauge and set the new one the same.

Oct 11, 2011 | 1993 Buick Regal

1 Answer

1989 Buick intermitent engine problem Buick Regal 3.1 V6 8th vin. T in nostart condition no fire @plugs no fuel pressure when cranking . Replaced : crank sensor ECM Ignition module ignition switch...


You did'nt say if you have had the car (Scanned) to see if the engine control Module has stored any fault codes. You say it runs 20 miles or so before it quits. After cooling does it alawys start back up? What have you been doing to get it running again? The ECM can warm up and quit. It'll get an Troblem code about though. The no spark at the time sort of removes the Cat converter overheating and the ingtion Module ( (the coils are mounted to it). Something getting too hot is likly. Crank sensers and cam sensers both wil do this the crank senser is on the back of the block just above the oil pan. The cam sewnser is underneath the power steering pump and the connector going to it is on top of the front valve cover on the passenger side. Crank sensers will not code and still be bad. Computers if they come back on ever they will code most any problem and the code name is Quad driver failure.

Jul 23, 2011 | 1989 Buick Regal

3 Answers

I have a 1999 buick regal ls dying.


I have a 99 Buick Regal and it too dies out, but only when I use my turn signals. Sometimes, when trying to start the car...the dash lights would flicker and you can hear some sort of electrical ticking sound. As of today, my car will not start (5/24/09) it hadn't turned over since yesterday. After a process of elimination and searching the net, I think I need a new ignition switch. You may need one as well.

May 18, 2009 | 1999 Buick Regal

1 Answer

1992 BUICK REGAL WON'T CRANK


the MAP ( Manifold Air Temperature ) its data is used to control fuel ratio / NOT THE DELIVERY OF FUEL Did you check the FUEL FILTER ?

Apr 16, 2009 | 1992 Buick Regal

1 Answer

Buick regal 1996 crankshaft position sensor


IF THE CRANK SENSOR GOES BAD ON THAT ENGINE THE CAR WILL STOP RUNNING OR NOT START IF TRYING TO START IT. NEED THE CODE INFO TO HELP YOU FURTHER. TRY GOING TO ADVANCED TO GET THEM TO READ THE CODE-THEY DO THIS FOR FREE.

Aug 26, 2008 | 1996 Buick Regal Olympic Gold

Not finding what you are looking for?
1992 Buick Regal Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...