Question about 2003 Mitsubishi Diamante

Open Question

Pajero immobiliser will not allow car to start

Unfortunately only have key, no remote button on key fob, can immobiliser be de-immobilised, bypassed, disconnected, reset?
pajero is swb 3dr 1998 2.8D turbo Inter. please

Posted by on

6 Suggested Answers

  • 566 Answers

SOURCE: i own a 1992 pajero,

hi not sure if this will work on pajero but worth a try ?? insert key and turn ign on only ! then press key fob lock button for 10 seconds then turn off ign and remove key wait 10 seconds thenpress lock and and unlock on remote fob if this works ? the immobiliser will have reset hopefully ? and car will start ? will keep fingers crossed for you best of luck!

Posted on Nov 05, 2008

  • 3 Answers

SOURCE: miss fires and cuts out when cold its a pajero 2.8 diesel turbo

hi you need to change the fuel pump seals, whats happening is there letting in air causing engine to cut out a commom fault with this vehicle.

Posted on Dec 31, 2008

localwonder
  • 6784 Answers

SOURCE: pajero transmission oil change due?

The first change/flush will usually be at 75,000-100,000 mi.

Posted on Apr 14, 2009

  • 25 Answers

SOURCE: rough idle / what is correct idle 25 td. swb pajero

I have a 98 Montero Sport and to adjust the idle all I needed was a phillips screw driver. Check owners manuel for Idle speed and remember to have lights off when adjusting. Also it showed the idle range posted on the hood underneath.

Posted on Jun 08, 2009

  • 1 Answer

SOURCE: 1987 Mitsubishi Pajero 2.5 turbo diesel not starting

Hi, there is a little cable that in on the starter motor, probably you have just disconnect it, it happens to my pajero lot of times. look around the starter motor for a cable that is not going somewhere and then locate the little connector on the top and rear part of the starting motor. if this is not the case then try another battery, pretty sure one of the two is the problem.

Ioannis

Posted on Jul 01, 2009

  • 3 Answers

SOURCE: 4M40 engine lacking power and blowing black smoke.

http://www.delicaclub.com/load.php?id=20

Install the egr mod, will stop it smoking in no time
Delica owner...

Posted on Dec 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i bypass the immobiliser


Did you try replacing the batteries in the key FOB?

Nov 09, 2014 | 1996 Kia Sportage

1 Answer

Will I be able to start and use my car if the key fob/plip isnt working?


everything should be ok as long as u got the key to start the car

Jul 07, 2014 | 1999 Renault Megane

1 Answer

Mercedes key remote


you probably will not start the car as the immobiliser needs the key battery to transmit the code to allow the immobiliser to work correctly. Fit a new battery in the key fob and have it reprogrammed to the engine CPU.

Jan 10, 2014 | Cars & Trucks

1 Answer

Immobiliser problem with a 1994 VW Golf 1.9TD which does not have central locking.


Unfortunately there is no way to bypass the immobiliser on this vehicle, the immobiliser communicates with the control unit which then send s a start signal to the ECM to start the car, There are companies in the UK that can re-program the ecm to ignore the immobiliser but this isn't very cheap. You best option is to try to find a car at a dismantlers and replace the damaged part yourself.

Mar 02, 2012 | Volkswagen Golf Cars & Trucks

1 Answer

Imobiliser problem


If im not mistaken,your car should have an alarm reset/override.Below the steering column,on the dash should be a slot where you put your remote transmitter to deactivate the alarm.If that works,you then need to have your remote checked and coded by a vw dealer.Good luck.

Jun 16, 2009 | 1997 Volkswagen Golf

1 Answer

2008 Hyundai i30. 2.0 litre petrol. (Elantra selected, since I believe i30 is same basic engine system as the Elantra, and i30 is not a provided option for my model on this forum). Car won't start. Engine...


Interesting problem.. since not US spec. Is there a 'remote keyless (fob)' programmed for this vehicle? That's the only way to DE-arm the immobilizer (anti-theft) feature (based on US specs). Unless you have this key fob (keyless entry remote... which must also be programmed for this vehicle), the only other way is wait 5 minutes with the existing key in the ignition, then it should start (US specs). You will still need to have an 'ACTIVE' keyless remote programmed for this vehicle... otherwise, you'll continue to run into this problem.

Apr 18, 2009 | 2008 Hyundai Elantra

1 Answer

Immobiliser problem - 94' Golf Mk3 GTI 2lt 8 valve


just unplug the immobiliser unit. its behind the glove compartment for rhd models.

Mar 15, 2009 | 1997 Volkswagen Golf

1 Answer

I own a 1992 pajero, the battery in my keypad went flat and since changing it i haven't been able to start my car as the immobiliser doesn't recongise it any more, any ideas on how i can fix this??


hi not sure if this will work on pajero but worth a try ?? insert key and turn ign on only ! then press key fob lock button for 10 seconds then turn off ign and remove key wait 10 seconds thenpress lock and and unlock on remote fob if this works ? the immobiliser will have reset hopefully ? and car will start ? will keep fingers crossed for you best of luck!

Nov 05, 2008 | Mitsubishi Passenger Cars & Trucks

Not finding what you are looking for?
2003 Mitsubishi Diamante Logo

Related Topics:

329 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...