Question about 1999 Pontiac Grand Am GT

1 Answer

Harmonic balancer on a grand am

I have a pontiac grand am 1997 is it easy to replace the harmonic balancer myself? Where could I find step by step instructions?

Posted by on

  • 2 more comments 
  • girardgene62 Feb 11, 2009

    To clarify further the serpentine belt is loose not charging the alternator car wont hold a charge ect..
    I was just wondering if it is a simple process of pulling the old part and replacing it?


  • yadayada
    yadayada May 11, 2010

    same answer

  • yadayada
    yadayada May 11, 2010

    it is a bear of a job de to close clearance and little working space.

  • Anonymous Mar 15, 2014

    crank position sensor

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 2,039 Answers

You have to remove the center bolt of harmony its depend what engine you have most likely you need a little puller if the belt loose check the belt tensionner to see if its not broken pierre

Posted on Feb 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Harmonic balancer seal-1997 plymouth grand voyager van


Depending on the amount of room to the radiator / fan shroud it is not excessively difficult to do if you have the correct tools. You will need a 1/2 inch impact gun , harmonic balancer remover, screw driver, hammer. a piece of pipe the same size as the outside dia of the seal and a hammer along with a selection of spanners and sockets to remove the fan belt and anything else that will be in your way.. IF the balance is held on with a bolt then the easiest thing is the impact gun. the harmonic puller to pull the balancer off with, the pipe and the hammer to replace the seal. the screw driver to pry out the old seal

Dec 22, 2013 | Cars & Trucks

2 Answers

Had my Harmonic Balancer replace now it shuts off after 10 mins of it being on


the garage may have did something to the crank position sensor that is located behind the harmonic balance. there is a ring gear there to for the timing

Oct 30, 2012 | 2001 Pontiac Grand Prix

1 Answer

What pulley do you use to take off the harmonic balancer on a 97 grand prix


I wouldn't use a "pulley". I would use a harmonic balancer puller (available at most parts retailers).

May 31, 2012 | 1997 Pontiac Grand Prix

1 Answer

Where is located the crank position sensor in a 1992 pontiac grand prix 3..1 engine


the crank position sensor(cps)is located behind the harmonic balancer where it picks up the signal from the shutters attached to the rear of the harmonic balancer.

Apr 01, 2011 | Pontiac Grand Prix Cars & Trucks

1 Answer

I am needing to replace the harmonic balancer on my 1997 jeep grand Cherokee. Will you please send me replacement instructions? Also, I would appreciate any helpful tips and a list of required tools. Thank...


first you will need to remove the belt. then you might have to remove the electric fan. (depending on what engine you have) then you will need remove the bolt from the harmonic balancer. i think its a 21 mm. then you need to get a harmonic balancer pulley puller. you can rent one at your local auto parts store. install the puller and remove the harmonic balancer. then put new one on by using the bolt. reinstall all components in reverse. this one is pretty easy to do. please rate thank you.

Jan 05, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

How come the harmonic balancer is not lined up with the other pullies and the belt keeps slipping off or breaking in the middle?


the harmonic balancer is bad they have a rubber bushing in them which goes bad and sets them off the rest of the pullys you will have to replace the harmonic balancer and that should take car of the problem if you have any other questions feel fre to ask hope that info helps

Nov 22, 2010 | 2002 Pontiac Grand Am

1 Answer

How do you replace crank sensor on a 2006 pontiac grand prix with the 3800 series 3 motor?


YOU HAVE TO REMOVE CRANKSHAFT HARMONIC BALANCER TO REPLACE CRANKSHAFT SENSOR.ITS LOCATED BEHIND IT.YOU NEED A HARMONIC BALANCER REMOVAL AND INSTALLER TOOLS.

Sep 13, 2010 | 2006 Pontiac Grand Prix

1 Answer

Harmonic Balancer needs replaced. How long can I wait until I have to get this done?


its bad the harmonic balancer , balances the crankshaft in relation its a dapener as well as it rotates the timing ..change it soon...

May 07, 2009 | 1999 Pontiac Grand Am GT

2 Answers

Harmonic balancer


what are the steps to removing a harmonic balancers

Oct 18, 2008 | 1997 Chevrolet Corvette

Not finding what you are looking for?
1999 Pontiac Grand Am GT Logo

671 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...