Question about 1997 Ford Mustang Cobra

1 Answer

How to replace 97 mustang v6 3.8 tensioner - 1997 Ford Mustang Cobra

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 449 Answers

You have to loosen the tensioner pulley bolt there is two of them.

Posted on Feb 11, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

97 ford mustang.the fan won't change positions

First thing I would check is all of your vacuum lines. I had same problem and turned out there was a split in one of my vacuum lines. Once I repaired it, it worked perfectly again.

Jul 26, 2011 | 1997 Ford Mustang Cobra

1 Answer

I bought a 67 Mustang 200ci today and popped the belt on the way home. I replaced the belt but found no legit way to properly tension it, any suggestions? It squeaks like crazy

Belt tension is adjusted by moving the alternator away from the water pump. Loosen both alternator bolts (don't remove them) and place a pry bar or wooden handle between the alternator body and the engine block. GENTLY apply pressure to move the alternator away from the engine - when the belt has less than 1 inch vertical play, tighten the alternator bolts while maintaining tension on the alternator. If proper tensioning doesn't solve the squeal, then I would suspect the new belt is contaminated with oil or grease.

Feb 15, 2011 | 1966 Ford Mustang

1 Answer

When i try to tension my timing belt on my 97 2.2 it does not tig

the belt may be worn out or the tensioner needs replaced.

Jul 29, 2010 | 1997 Honda Accord

1 Answer

Getting no fire from ignition switch to starter on 97 mustang

Sounds as if the starter relay switch needs to be replaced

Jul 24, 2010 | 1997 Ford Mustang Cobra

1 Answer

How to adjust belt tensioner on 5.0L 89 Mustang? (I need to replace alternator)

Use a socket or box end wrench on the bolt at tensioner pulley in centre and lift up. Counterclockwise.

Nov 28, 2009 | 1989 Ford Mustang

1 Answer

How to remove fan belt on my 1996 ford mustang?

Take tension off the tensioner and take belt off. You put wrench on the bolt that holds the pully on and pull - tension will come off the tensioner and you remove the belt.

Aug 02, 2009 | 1996 Ford Mustang

1 Answer

Change head light on 97 mustang

The actual light? or just the bulb inside the light?... If you mean the whole light then pop the hood and look around the lens and you will a few screws that hold it in place. Remove and replace. If you mean the bulb, pop the hood and and look behind the light cover and you will see where the light bulb attachment screws into the back. Unscrew the attachment and remove the bulb. When you replace with the new bulb be careful to not touch the bulb with your bare hands as a chemical reaction will cause the bulb to burn out faster than normal. Put it all back together as it was before and you are good to go. 

May 06, 2009 | 1997 Ford Mustang Cobra

1 Answer

How to replace 97 mustang tensioner

the tensioner is under the belt remove the belt first and then you remove the tensioner and after you install the tensioner use the tensioner to reinstall the belt be sure to take off the negative side of the battery first for safety

Feb 11, 2009 | 1997 Ford Mustang Cobra

2 Answers

Replace fan belt

Here is a diagram
its pretty simple use a wrench/hex which ever applies to the nut that on the tensioner some vehicle have a regular bolt type and some have a hex. Just follow illustration and push on tensioner using proper tool and release tension and belt and the belt will come and replace using the routing diagram I provided. Good Luck and Thanks for using FIX YA contact if you need more help.

Dec 31, 2008 | 2002 Ford Mustang

1 Answer

My transmission wont go into gear none of them work 1,2,3,4,overdrive, or reverse My 97 Mustang turns on alright, but I can't shift it out of Park. It's totally stuck. Help?

Suggest you check your linkages to the tranny first, ensure nothing is bent. If your shift is controled with a wire cable, check it out also, maybe is rotten.

Additionally, you didn't clarify if your wheel is straight or turned to the extreme right or left. If that is the case, example: if the wheel is locked in the left turn position, pull on the steering a bit harder to the left to release the lever tension, that might get you out of park. Good luck!

Dec 08, 2008 | 1998 Ford Mustang

Not finding what you are looking for?
1997 Ford Mustang Cobra Logo

Related Topics:

434 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5648 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides