Question about 1999 Honda CR-V

Open Question

How do I remove damaged bumper from 1999 Honda CR-V?

I've recently bought a new bumper for a '99 Honda CR-V and have removed 8-10 screw-washer combo's and a couple of hex-type bolts from the old bumper. I also tried to unscrew the center piece (right above the nose of the bumper) that sits between the lights and the bumper still won't budge after removing a couple of screws in that as well. Can anyone give me some hints on how to remove the bumper? Thanks!

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bodyguy
  • 5 Answers

SOURCE: How to change the whole headlight assembly on a 05 Honda CRV

When you raise the hood, look for a Phillips screw that holds the parking lamp in. if it is there remove screw and pull parking lamp toward front of vehicle. If headlamp and side lamp are 1 piece, there should be 2 number 10 mm headed bolts that are vertical, that hold the assembly in. The side lamp will have a stud that holds the light to the fender. You may have to pry it loose. Reverse procedure to install.

Posted on Dec 23, 2008

  • 496 Answers

SOURCE: removing rear light assembly on honda odyssey 2006

Yes, there is a "spear point" plastic clip that is still engaged into a socket type holder in the front outboard portion of the tail lamp assembly. Pry gently with a tape wrapped screwdriver at the front outboard corner of the assembly and the clip will release. You will then be able to see how the clip works and will be able to align and engage it first when replacing the tail lamp assembly.

-T

Posted on Jan 24, 2009

  • 1 Answer

SOURCE: How do I remove the radio from a 1998 Honda CR-V?

UNSNAP PUSH-PIN FASTENERS FROM BOTTOM OF CENTER CONSOLE
AND REMOVE BOTTOM PANEL.
2. EXTRACT 4 SCREWS FROM BOTTOM EDGE OF BEZEL. EXTRACT 4
SCREWS FORM INSIDE DASH BELOW POCKET. PULL CUP HOLDER/
POCKET ASSEMBLY OUT OF DASH AND REMOVE.
3. OPEN GLOVE BOX AND REMOVE STOPPERS. EXTRACT 2 SCREWS
FROM RIGHT SIDE OF CENTER DASH BEZEL..
4. FROM BELOW STEERING WHEEL EXTRACT 2 SCREWS FROM BOTTOM
EDGE OR PANEL, UNSNAP UPPER EDGE OF PANEL, UNPLUG, AND
REMOVE.
5. UNSNAP TOP EDGE OR CENTER LOWER BEZEL, UNPLUG, AND REMOVE.
6. EXTRACT 2 SCREWS FROM SIDES OF POCKET.
7. UNSNAP RADIO/AC CONTROL DASH BEZEL, UNPLUG, AND REMOVE.
8. EXTRACT 2 SCREWS FROM EACH SIDE OF THE RADIO BRACKET
ASSEMBLY TO REMOVE RADIO FROM DASH/AC BEZEL.

Posted on May 18, 2009

  • 1 Answer

SOURCE: 2005 odyssey tail light bulb replacement,how to do

There is a little connector to the front of the lense assembly, you will need to pop that out... Carefully use a screwdriver to accomplish this...86f2b5d.jpg
You can see the white plug of the connector below

4cc118a.jpg

Posted on Jun 20, 2009

  • 1 Answer

SOURCE: how to replace tail light bulb - 05 Honda Odyssey

Yup after removing the 2 screws, there is a round plastic tap.
you need to pop the light housing back and outward with a flat screwdriver. wrapped electrical tape on the flat end to avoid scratching the paint.

Posted on Mar 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace d4 gear indicator light inmy 1998 honda cr-v


I have a 99 CRV and I would think it would be the same. Sitting in the drivers seat remove the two screws at the top of the gauge cluster. Pull out on the top of the cover with some force and the clips that hold the bottom of the cover will release. Now remove the screws holding the gauge cluster, two top and two bottom. Pull straight out a few inches so you can turn to the side and remove the wire plugs on the back, be careful not to damage the wires. With the cluster removed there is a white box on the back that needs a small flat blade to remove. Once removed the small lamps can be replaced. Tools needed are a Philips and a small flat blade screwdriver

Jan 24, 2011 | 1998 Honda CR-V

Tip

How To Install Replace Front Bumper Cover Honda CR-V 02-06 1AAuto.com


How To Install Replace Front Bumper Cover Honda CR-V 02-06 1AAuto.com

on May 10, 2012 | 2002 Honda CR-V

1 Answer

Headlamp


Yes, you have to remove the front bumper fascia, it is not as difficult as it seems, lowering the fascia will reveal the two or three bottom screws for the headlight assembly. Also take out the inner plastic fender ( 3 or 4 self locking plastic plugs) if you need to reach the connector for the turn signal bulb.

Jul 24, 2010 | 1999 Honda Accord

1 Answer

Can you help me dis-assemble my front bumper honda odyssey 1999 ?


Front
  1. Note the radio security code, then disconnect the negative battery cable.
  2. Remove the bolt from the lower part of the bumper just in front of the wheel opening, and remove the self-tapping screw from the rear most portion of the bumper at the forward portion of the front wheel well.
  3. On V6 Odyssey models, perform the following:
    • Remove the grille.
    • Remove the pins and clips from the lower front of the bumper.
  4. On 4-cylinder Odyssey models, remove the bolts from the left and right side lower brackets for the bumper at the ends of the lower air intake.
  5. Pull the ends of the bumper outward.
  6. Have an assistant help guide the bumper up and away from the vehicle.
  7. Installation is the reverse of the removal procedure.

Mar 06, 2010 | Honda Odyssey Cars & Trucks

1 Answer

Remove lower rear trim beneath tailgate


Easy. First you need to remove the rear splash guards(the plastic pieces located near the tires)
After that, it should be about 6 bolts/clips and they are located in plain view just standing facing the bumper. Then the bumper pulls right out.

Good luck

Apr 20, 2009 | 2009 Honda CR-V

1 Answer

I have a 2005 honda civic coupe and I need to know how to remove my damaged rear bumper and instal the new one that I bought.


It is very easy. 4 screws, 2 bolts, and 2 clips.
2 on the top of the bumper, 2 underneath, and 2 in each rear wheel well.

Apr 01, 2009 | 2005 Honda Civic

1 Answer

Add front license plate, do I need to remove bumper to get behind


try using self tapping screws so you dont have to remove it, you can drill pilot holes if the screw wont go thru easy, and you dont need a nut/bolt

Mar 20, 2009 | 1998 Honda CR-V

2 Answers

How to change the whole headlight assembly on a 05 Honda CRV


You have to remove the front bumper and grill etc

There are 5 bolts holding the headlight assembly in place. 2 at the top and 3 underneath.

Remove the plastic cross piece by prising out the clips and then the grille clips too then unbolt the bolts eithr side under the wheel arch. The bumper is still fastened using cips. Pull the bumper forward to unclip.

Dec 23, 2008 | 2005 Honda CR-V

1 Answer

99 Plymouth Voyager Rear Bumper


If you look up from under you should see some push clips. if your removing entire bumper with rebar & all, it's probably about 4 nuts holding it to bumper shocks, but be sure to look near ends at fenders for push clips , and or screws, and across mid section. watch it, it's pretty heavy with the rebar attached so make sure you have everything ready & remove nuts last, with some help to hold it up.

Aug 05, 2008 | 1999 Plymouth Grand Voyager

Not finding what you are looking for?
1999 Honda CR-V Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...