Question about 1984 Isuzu Pickup

1 Answer

1984 pup transmision

I put a clutch in a 1984 pup,now the transmision is stuck in first gear but the shifter is in neutrual postion and wont shift to any gear besides reverse and when i let out the clutch it stalls while in reverse

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

The shifter forks inside the trany is hung up take back out or slide back be sure in neutral when u get it to shift then put back in

Posted on Feb 11, 2009

  • B.I. May 09, 2014

    double gear situation. remove top cover again and aline fork slots with a screw driver. while droping shifter in make sure that the nioprem bushing is on the ball at the tip of the bottom of stick in snaped in .once in place there shoudnt be any play or movement except the shif itself. any play is now slop situation. replace bushing. next time for any stick being removed, replace bushing. one time up one time down. with any garment,bushing,seals,O rings,brass or aluminum gaskets. any way problem persist its deeper than you want to opperate on. for me befor looking for replace ment dive in what the hell. cost you a day or two at the most. make you alittle wiser and youmighe figure it out. in anything around the house, even life. what makes it or why it does applys to a various veriety of fungtions. mahalo & ALOHA

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Howdo i find a 4 speed transmission to fit on a G200Z engin modle Isuzu pup 1985


I would start by calling local salvage yards and see what they have. If they don't have one they can usually put it on a parts seach and locate something.

Jun 07, 2015 | 1985 Isuzu Pickup

1 Answer

Manual transmission stuck first gear


I too say its a stuck shift linkage.
Open the link below to see the image.
The bushings (A, D and E) can wear out with time and use. I have seen the joint (at A) that attaches at the transmission get seized too. These parts can be removed from the car with the transmission in place. http://globalcarbrands.com/i/subaru/subaru-shifter/subaru-shifter-06.jpg

Apr 14, 2014 | 2001 Subaru Outback

1 Answer

My car wont shift out of 2nd gear.the shifting handle is sloppy and the clutch is working fine


if the clutch really is working, (lever at bell moves 3/4")
by fine, my guess, is you can take off from dead stop in2nd, right>?
then its a bad shifter. tip.
or linkage (end tranny extension housing)
or transmission actual core.(shift rails, or forks) or worse.
you do know ,that you can disconnect the linkage and test tranny.
by hand,
key off
leakage off
shift to neutral (read the FSM or alldata.com) for how. under M/T sections.
then key on start engine,clutch depressed, the lift pedel
car moves its stuck in 2nd, of not bad linkage.
can do all gears that way, use 2 people and do not stand infront of car doing test.
or put the front wheels up on stands. but do not get near them.
while engine is running.
btw some shifters have plastic parts that go bad in the shifter tip.

or ,
jack up car in front, can you now shift car in to neutral or any gear?
linkage tests.
remove shifter housing and below see the shifter, H pattern
sifter box mechanism.
see that. you can shift that by hand with any small wrench or
large screwdriver, if the works the parts on the end of the shifter
handle main shaft tip are bad.

Oct 19, 2013 | 1995 Geo Prizm

1 Answer

Car starts in neutrual put it in gear it stalls


Sounds like the torque converter solenoid is stuck open engaging the torque converter clutch.

Apr 04, 2010 | 2001 Hyundai Santa Fe

1 Answer

Car stuck in gear.I had to remove cv joint shaft in order to get moving.what could be the problem and what caused this?


Its probably shift linkage between shift handle and transmision get under car and find where the shifter comes through the cars floor and check the rod arms that run between shifter and tranny, if its good then its internal transmision.

Nov 18, 2009 | 2000 Volvo S40

2 Answers

1984 honda accord does not move when put into gear


The clutch could be way out of adjustment, the clutch could be completeley worn out, There is no connection between the engine and trans, meaning the input shaft is broken. A drivesahft could be broken (this usually makes a lot of noise when the clutch is let out) Hope that helps narrow it down, really hard to say without see the car.

Apr 20, 2009 | 1984 Honda Accord

1 Answer

Shifter wont shift the pickup into gear


Let's start with the basics. Key has to be in the ignition and ignition turned to the run postion. Battery has to be charged up. Brake pedal has to be depressed so the shifter will unlock, . If the shifter will not move, it could be several things. A faulty shifter unlock cylinder or wirng problem. A binding shiter cable or shift lever problem at transmission, or a problem with the shifter assembly on the steering column.

Mar 03, 2009 | 1996 Ford F150 Regular Cab

2 Answers

1988 suzuki samurai WONT MOVE


First thing just try to push or pull the 4x4 lever if you get it to move and it feels like it went into some gear try to drive the truck.If this works look on the shifter for the 4x4 and put it in 2 wheel drive (H2 is two wheel drive,H4 is 4x4 high,and L4 is 4x4 low range).Make sure you have the clutch depresed when you try to move the 4x4 lever.If you try this stuff with no fix try and look for clutch adjustment on the transmision you may need to adjust it or your clutch is bad.

Aug 30, 2008 | 1988 Suzuki Samurai

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...