Question about 1999 Chevrolet C1500

Open Question

Crimestopper remote car starter does not work

I have a crimestopper remote car starter that stopped working 2 yrs ago, didn't quite bother about it till date. I do remember chaning my car battery around that time. Would that cause this issue? If so, please help me with instructions on how to fix this? The FCC ID given on the remote is crimestopper - FCC ID: CHXP19695.

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 147 Answers

SOURCE: 2003 Chevy Impala. Changed the door remote & still not working

If your dealer is nice they may charge about a half hour of labor. Most charge about an hour. I would guess $50-$100.

Posted on Mar 31, 2009

  • 120 Answers

SOURCE: 2007 Chevy Equinox - with

believe it or not you need to take it to the dealer. There is a software reprogram for the remote control door lock receiver to fix the probelm - really common on tahoes and suburbans. Go to the dealer and tell them about bulletin #06-08-52-002g. It probably will need new remotes also. Try and get the dealer to warranty it since its a known product defect and a known problem

Posted on May 03, 2009

  • 1 Answer

SOURCE: My car key/remote lock and unlock stopped working.

happened to me once. the fuse for it was blown. $3 fuse replacement. check the fuse box & manual for this component. the fuse removal tool is located inside the engine fusebox area, and the fuse for the lock is inside the driver side box.

Posted on May 14, 2009

  • 2418 Answers

SOURCE: My Flux Capacitor isn't working - Car won't time travel

Simple fix, Check your wiring to the flux cap relay, your must have the polarity backwards. The wiring digram you received with the cap kit is for European 50 hz. You will have to reset the relay with a spike voltage of 13.9 vDC Hooking the neg to the pos and touch for just a second. rewire as per the directions be careful to install the 100 ohm resistor across the relay terms # 87 and 86 the .47 mf cerm. cap will now be wired across the wiper relay to engage fast forward or step thru time, this will reset for 60hz USA quad voltage used in this system. See you in a few.

Posted on Jul 18, 2009

  • 5 Answers

SOURCE: remote start does not work

henryj153, no offence guy, but if you dont know something, dont try and give advice. Now for the guy with the problem mattpointer:
These cars come with remote start as an option, and it is problably your BCM (Body Control Module), which is a $380 part, and the dealer has to install it, because of the programing... Here is a free way of checking if that is it. This part ties in certain vehicle systems, and for some reason when the BCM goes bad, so does the GPS, that is tied in with OnStar Check to see if your onstar can recieve GPS... press the blue OnStar button and ask them to locate you. If you dont have the service, they may want to start the service, just humor them as if you were interested, and ask them to locate you first, because you want to make sure the equiptment works. If they cant locate you, but you are able to use OnStar to contact them, most likely The BCM is bad, and thats what it is. This car has some great technology, but the intergration of this tech is in the BCM, and it goes bad.... so its a trip to the dealer for you my friend.

Posted on Feb 05, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Would the anti-theft keep my 1999 ford windstar from starting


(No starter action at all)... If the starter is engaging not the trouble)

Your key as a weeny teeny transponder in it... which could get damaged(washing machine, dropped or broken).

Try THAT all important second key...
If the second key fails to get any starter action you DO need to look into your PATS (Passive anti-theft system),

Hope this helps.

Amazon com 2 PAIR NEW Ford PATS Transponder Chip Key Blank USER...

Amazon com Crimestopper KEY OVERRIDE ALL Self Learning PATS Data Bypass...

Dec 08, 2016 | Ford Cars & Trucks

1 Answer

The siren on my crimestopper alarm isn't working it seems like its in silent mode when I open the trunk with it armed all it do is flash the lights

check the wire from the module to your siren, it could be loose or cut. if you have a tester test each wires that leads to your siren for continuity, it may be broken and need to be replaced. I hope this helps you, good luck.

May 27, 2014 | Cars & Trucks

1 Answer

How do i reprogram my crime stopper car starter?

Sounds like it wasnt programed right to begin with.if the check engine light is on you could try reset or even if its not on just disconnect battery cable for about 10 to 20 mins then hook back up see if it resets system that way sometimes that works for program faults.if not and u have numerous problems with this you need a dealership to check this out it could be causing complications with the anti theft security.just try disconnecting battery first go from there

Apr 26, 2017 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Crimestopper SP501 car alarm/remote starter will not respond. The 2 way one doesn't work, the sidekick does.

You need to program your crimestopper sp-501 key fobs, you need to program both the 2-way and the 1-way key fobs, during the same key fob program session. First find your valet button/switch, when you have found it, turn your ignition on and press the valet button four times, if you have a toggle type switch for a valet switch, toggle it up and down four times, when its in remote key fob program mode, it will honk your horn 4-times followed by 4-parking light flashes. Once your have done this press the lock button on the 2-way key fob, horn will honk and the 2-way will sing a little song to confirm programed, then press the lock button on the 1-way key fob the horn honk will be your confirm programed. turn ignition off this will exit you from program mode. then shut all doors and test key fobs for operation functions....hope this helps you out

Dec 03, 2011 | 2006 Hyundai Sonata

1 Answer

I have a crimestopper alarm. Out of the blues, the alarm stopped working with the car. The remote battery was changed but still no good. Is there anyway to fix it? Thanks in advance, Jimmy

you need to check the fuse to the alarm as well if that fails look through the phone book to find a place that install your kind of alarm and they maybe able to help you if you have a booklet to your it maybe a 800-number in there wish you the best of luck Michigan Man.

Sep 16, 2010 | Toyota Avalon Cars & Trucks

1 Answer

Deactivated remote start system

you can find the manual for your unit at but first you have to look under the dash and get the actual model number from the unit the go to go to support choose manuals and manuals again then locate your model number from under your dash to get the correct manual you should be able to print it out and then you may take it somewhere you can also contact crime stopper tech support at 800.998.6880 ext 210

Apr 01, 2009 | 2003 Jeep Liberty

Not finding what you are looking for?
1999 Chevrolet C1500 Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides