Question about 1989 Oldsmobile Cutlass Ciera
I need a wiring diagram for 1989 cutlass ciera power window switch. it is a 4 button switch.
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Disconnect the battery negative cable, carefully remove the door panel, make sure you remove all the visible hold down screws holding the arm rest and other things in place, be careful and observant, don't force anything. If you don't have the standard door panel removal tools, use a stiff putty knife or a wide screwdriver to remove the door panel, you will have to get the power window control switch and the lock control rods out of the way, take notes so you know how they go back together, Remove the plastic weather protection shield out of the way, try not to tear it because you will want to replace it using a good contact adhesive. Getting the motor and the lift mechanism out is the biggest challenge, There are two big rivets holding the motor and regulator assembly to the door, there are two more rivets closer to the rear of the door that holds the track and window guide in place. the rivets are difficult to drill out because it's not easy to center punch them. I used my 4 inch grinder to remove the rivet heads, be careful not to injure yourself or grind through the door metal. knock the rivets out. Remove the power supply wire from the motor. Use a 10 MM socket to untighten the two cap screws that hold the lift bracket to the bottom glass channel. Don't take the cap screws all the way out. Use a piece of wire to hold the window in the closed position. Loop the wire over one of the hold down cap screws and fasten the other end through one of the convenient holes near the top of the door. Now comes the good part. the motor and lift mechanism is all in one near rigid piece. The seat belt anchor blocks the door panel opening that would make it relatively easy to remove. Don't give up, the unit will come out with some thoughtful manipulation, the V shaped track guide will tolerate a small amount of flexing, don't overdo it. I finally got the assembly out by moving it as far to the back of the the door cavity as possible, use the angles of the assembly to your advantage to free it from the door. Once free, use a black marker to ensure you align your new motor in the correct postition. If you are replacing a complete assembly that looks the same a the part you removed, install by reversing the above directions. If you are replacing only the motor, drill out the two rivets that hold the motor to the lift assembly. this will be asy to do. fit your new motor in the exact same position, referring to the previous marks you made. If you are reusing the old lift mechanism, you should pull the perforated tape out of the guide, clean, inspect it, the guide and the tape, relubricate it, I used white grease, there is probably a better grease available. The motor assembly I received from an internet supplier came with rivets and machine screws to install the assembly, I used 1/2 quarter twenty nuts and bolts to replace the big rivets, I don't have a big enough rivet gun. If you go the quarter twenty way, use thread lock, install with bolt heads on the inside the door and flat washers and nuts to the car interior. Be observant, I left the plastic bracket that attaches the drive tape to the window bottom in an unsecure place, one of my dogs used it as a chew toy,so it was off to the junkyard one more time. Be sure to secure the tape properly at both ends. If it worn or frayed, several suppliers including rockauto supply them at reasonable cost. good luck.
Posted on Oct 10, 2008
This should Help. Please Rate My Response! Thanks!
Posted on Feb 04, 2009
SOURCE: 1991 olds wont start
I have no spark. Changed the CSS and still no spark. I also changed the Coil packs with a junk yard 1. Does anything else control spark other then ECM?
Posted on Jun 18, 2009
they can be bought on line but the easiest way is to buy a manual from local parts store, or possibly check one out of the local library
Posted on Dec 06, 2009
Tips for a great answer:
Apr 03, 2012 | 1989 Oldsmobile Cutlass Ciera
Jul 14, 2011 | 1988 Oldsmobile Cutlass Ciera
Apr 12, 2011 | 1994 Oldsmobile Cutlass Ciera
Part #: FS20072
Mfr #: 20072
Dec 17, 2010 | 1989 Oldsmobile Cutlass Ciera
Nov 28, 2010 | 1989 Oldsmobile Cutlass Ciera
Sep 03, 2010 | 1989 Oldsmobile Cutlass Ciera
Aug 26, 2010 | 1989 Oldsmobile Cutlass Ciera
Apr 18, 2010 | 1996 Oldsmobile Cutlass Ciera
Sep 29, 2008 | 1992 Oldsmobile Cutlass Ciera
Feb 18, 2016 | 1989 Oldsmobile Cutlass Ciera
Oct 04, 2014 | 1989 Oldsmobile Cutlass Ciera
361 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: