Question about 1997 Volkswagen Eurovan

1 Answer

Intermitent or no spark 2.5 petrol Caravelle

Plugged in with snap diag. it said cam pos sensor. got new one it now says crank sensor or eng speed sensor but cant find it anywhere

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

The crank sensor should be located on the transmishion and this is probly what is throwing the idle off

Posted on Feb 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What could cause a1991 suzuki samurai to have no fire from a new coil?


no spark from coil directly?
is the cam turning, is the dizzy rotor spinning. ????

check all fuses first. Ig-coil, FI and dome.
then using diagnostic jumper wire or fuse, (as approp)
crank engine look for code 41 o 42.!!!

USA cars , answers only
our cars are all EFI that year.
no engine swaps to Suzuki G16A/B sidekick or tracker engines.!
1: engine cranks
2: no spark
3: The ECu makes spark
the CMP sensor in the DIzzy , (never fails if rotor turns, does rotor turn, if not cam belt igored and now snapped.)
the cam turns. the CMP fires. the ECU takes this CMP signal
and fires the ignitor next to coil and the coil charges, and release and BAM spark.

that is it.
the ECU will tell you when the CMP dies or the Ignitor fails
why not ask it.
1: key on
2: diagnostic jumper in place (flashes 12s for ok)
3: crank engine,for 5sec, not 1 ,not 2.
3: release key not off.
4: see code 41, or 42, BINGO !@!!!!

Aug 15, 2014 | 1991 Suzuki Samurai

1 Answer

Engine cant start because they is no spark.isuzu kb 220


welcome to USA
the country with NO KB trucks
that means no books to match.
books are necessary.
no year stated or country or size engine. ok its petrol got that.

spark , are all sparks dead or just one or a pair.
wow, engine cant run on 1 cylinder can they.
if spark is dead on all cylinder you must scan the PCM to see why.
cam belt snapped.
CMP sensor dead
CKP sensor dead.
coil pack dead. (how many does it have, I cant see our engine or spark wires, so can never guess )

Dec 23, 2013 | Isuzu Cars & Trucks

1 Answer

Starter cranks but no spark


Have you looked at the ignition module, or and ignition switch. Not the key switch} ignition switch.

Sep 11, 2013 | Plymouth Neon Cars & Trucks

1 Answer

1992 mx-3 v6 won't start. will hit sparaticly as if about to start but just won't catch. checked crank pos. sensor. need suggestions on how to proceed.


Check for a blue snapping spark on 2 or 3 plug wires(or all of them). If you get good spark, then ignition is likely not the problem. A weak or sporadic spark could be a bad coil or coil pack, or a bad ignition module (the ignitor).Check the coils with a volt-ohmmeter per the specs for your car. The ignitor can be tested at a parts store.
If spark is good, check fuel filter, fuel pressure, check timing marks on crank pulley and cam marks, Try a little starting fluid in the air intake and see if it runs for a moment. If so, then it's likely a fuel delivery problem. If no change, then it's likely an ignition circuit problem.
Good luck.

Dec 30, 2011 | 1992 Mazda MX-3

1 Answer

Volvo 850 2.5 non start - even RAC PUZZLED


check inside distributor cap for cracks also rotor arm condition also check crank angle sensor on top of bellhousing also cam sensor mounted near distibutor

Jan 23, 2010 | 1995 Volvo 850

1 Answer

99 Jeep Cherokee Sport, 4.0L -won't start


you need to have it connected to an OBD2 machine and watch if you are missing the cam sensor showing RPMs
or if your missing crank sensors RPMs,
it could be a wiring problem or computer if your seeing the RPMs from both sensors,and the last thing i would check is hooking up a fuel gauge to the reed valve and watch what fuel pressure you have while cranking,if the cam sensor is the culprit it will turn the fuel off after the cranking.

Jan 11, 2010 | 1999 Jeep Cherokee

1 Answer

No spark, 1988 Toyota Camry 3SFE 4cyl, 5 speed.


there is no crank sensor on this vehicles 2.0L. If you have power to the coil, new coil, cap and rotor try this if not done yet>>>Unplug coil power first....Try pulling off the distributor cap, and make sure the rotor is spinning with the cam...If this fails to spin, inspect the entire distributor assembly. If it passes, Inspect all the power circuit and wiring to the dist assembly, if ok possible ecu. i recommend having a mechanic check it out!! Hopefully this helps...please rate...thanks

Aug 11, 2009 | 1988 Toyota Camry

3 Answers

Buick lesabre no start


Hi you have replaced allmost everything ,(try fuel pump relay)

Jul 31, 2008 | 1992 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64286 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...