Question about 1994 Land Rover Discovery

1 Answer

How to change c.v joint

I need to change my front driver side c.v joint on my 91 discovery.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 275 Answers

Remove wheel, brake caliper and disc, end cap and circlip (if fitted) 6 bolts that hold the hub drive, undo and remove the hub nut by knocking back the lock washer, remove the inner hub lock nut and remove the hub assembley. remove the 6 bolts that hold the hub shaft and remove that.There will be either oil or liquid grease in it, Now you will see the drive shaft and CV joint, just pull it out. Clean all the oil or grease.knock off the old CV joint and knock on a new one, they have securing clips inside but will knock off with a hammer.refit is reversal of removal. Use silicon sealant to seal the hub shaft when you put it back. You will need to fill the swivel assembley with liquid grease. you will see the filler plug on the swivel housing, put in about half a liter Its possible you may need to replace oil seals, check as you go along. to adjust the hub play, tighten the inner hub nut until it goes tight then back it off until the hub can move freely and effortlessly, then grab the hub and pull back and forth to see how much play is there, a little is permissable, so adjust to suit. Fit and lock the washer and tighten the outer locknut. Then as i said refit as you removed. These are safety related parts , so please make sure the items are tightly secured, aftreall you dont want the wheel to fall off.
hope this helps

Posted on Feb 14, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replace front universal joint on a 1998 land rover discovery

Take the tire off, caliper & holder, 4wheel drive hub & use a ball joint tool to press the old one out & the new one in.

Aug 31, 2014 | 1998 Land Rover Discovery

1 Answer

The driver side front tire wobbles

have u had your car lined up at a aliment shop if not your toe end and camber could be not adjusted right

Feb 11, 2013 | 1997 Mercury Cougar XR7

1 Answer

Hyundia matrix 1.6 is it hard to change a drivers side ball joint ?

It is very difficult and requires special tools and skills, you will also need to have the front end aligned after the part change.

Jan 16, 2012 | Cars & Trucks

1 Answer

Land rover discovery1 what is o/s drag link end

If you look underneath at the front, you will see a steel bar which goes between both front wheel hub assemblies. At each end is a ball joint.
The off side (o/s) end is the right hand (looking forward) or Drivers Side in the UK.
Hope this helps.

Oct 11, 2009 | 1994 Land Rover Discovery

2 Answers

Land Rover Discovery II 2002

does it also clunk when you are driving along in 1st or 2nd gear and take your foot off the throttle?...maybe a unijoint.

Aug 03, 2009 | 2002 Land Rover Discovery Series II

1 Answer

I need to change a ball joint on an avenger

I think that is only available as the control arm assembly. Check whth you local parts store.

May 04, 2009 | 1998 Dodge Avenger

2 Answers

Doing u joints on a b2200 and it will be mine frist time on one

can i have a diagram on how to change a universal joint for a 91 mazda b2200

Sep 16, 2008 | 1988 Mazda B2200

2 Answers

Car sways and wonders over road at speed

Check the wheel bearing free play by rocking the wheel side to side by hand . If you feel any knocking then they need to be adjusted.Also check the panhard rod bushes , this is the rod connecting the front axle to the chasis.Have the wheel alignment checked if these are o.k.

Jun 18, 2008 | 1994 Land Rover Discovery

Not finding what you are looking for?
1994 Land Rover Discovery Logo

1,768 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

77544 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides