Question about 1993 Chevrolet Camaro

1 Answer

How to change the windshield wiper motor

What is the easiest way to get to the windshield wiper motor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 469 Answers

Take the dash apart

Posted on Feb 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My wiper motor only works on high and stops were ever the wipers are at. And the washer motor doest #39;t work


Low Speed Windshield Wipers
Low speed is activated when the multifunction switch supplies a specific ground to the speed inputs of the windshield wiper motor module. The windshield wiper motor module then supplies ground to only the windshield wiper run/park relay coil, activating it. When the windshield wiper run/park relay is activated, the deactivated high/low relay connects voltage to the windshield wiper motor low input activating the wiper motor. The windshield wiper motor module continues to operate the windshield wiper motor in the same manner as in high speed, but in low speed with the wiper motor connected to the low speed input.
Washer System
The windshield washer is activated by the internal wiper motor module when it receives a ground signal input from the multifunction switch. Dependent on the switch selection, the internal wiper motor module activates the windshield washer relay (internal) by grounding the respective relay coil. When the relay is activated, it connects voltage to the washer pump while the washer level switch provides ground to the washer pump.
Visual Inspection Chart Mechanical Electrical
  • Windshield washer hoses
  • Wiper linkage
  • Multifunction switch
  • Battery junction box (BJB) fuse 110 (30A)
  • Central junction box (CJB) fuse 13 (10A)
  • Circuitry
  • Windshield wiper motor
Symptom Chart Condition Possible Sources Action
  • The wipers are inoperative
  • Fuse(s)
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test A .
  • The wipers stay on continuously
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test B .
  • The high/low wiper speeds do not operate correctly (intermittent wiper mode OK)
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test C .
  • The intermittent windshield wiper speed does not operate correctly (high/low speeds OK)
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test D .
  • The wipers will not park at correct position
  • Pivot arm adjustment
  • Linkage
  • Windshield wiper motor
  • REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section.
  • The washer pump is inoperative
  • Circuitry
  • Windshield washer pump
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test E .
Do you know how to do electrical testing ?
  • windshield wiper motor
  • PINPOINT TEST C: THE HIGH/LOW WIPER SPEEDS DO NOT OPERATE CORRECTLY (INTERMITTENT WIPER MODE OK) s6a~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
    Test Step Result / Action to Take C1 CHECK THE MULTIFUNCTION SWITCH
    • Key in OFF position.
    • Disconnect: Multifunction Switch C202b.
    • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
    • Does the multifunction switch pass the component test?
    Yes
    GO to C2 .

    No
    INSTALL a new multifunction switch. REFER to Section 211-05 . C2 CHECK CIRCUIT 57 (BK) FOR AN OPEN
    • Measure the resistance between the multifunction switch C202b-5, circuit 57 (BK), harness side and ground.
      s6a~tr~en~file=n0025872.gif~gen~ref.gif
    • Is the resistance less than 5 ohms?
    Yes
    GO to C3 .

    No
    REPAIR the circuit. TEST the system for normal operation. C3 CHECK CIRCUITS 56 (DB/OG), 61 (YE/RD), AND 63 (RD) FOR OPENS
    • Disconnect: Windshield Wiper Motor C125.
    • Using the following table, measure the resistance between the multifunction switch C202b harness side and the windshield wiper motor C125 harness side:

      Multifunction Switch C202b Windshield Wiper Motor C125 pin 6, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 1, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 4, circuit 63 (RD) pin 9, circuit 63 (RD)

      s6a~tr~en~file=n0025874.gif~gen~ref.gif
    • Are the resistances less than 5 ohms?
    Yes
    GO to C4 .

    No
    REPAIR the circuit. TEST the system for normal operation. C4 CHECK FOR CORRECT WIPER MOTOR OPERATION
    • Disconnect all wiper motor connectors.
    • Check for:
      • corrosion
      • pushed-out pins
    • Connect all wiper motor connectors and make sure they seat correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present?
    Yes
    GO to C5 .

    No
    The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. TEST the system for normal operation. C5 CHECK THE WINDSHIELD WIPER MOTOR
    • Key in OFF position.
    • Disconnect: Windshield Wiper Motor C125.
    • Carry out the windshield wiper motor component test as outlined in this section.
    • Does the windshield wiper motor pass the component test?
    Yes
    The system is operating correctly at this time. The concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

    No
    INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section.

    Jul 20, 2016 | 2006 Mercury Grand Marquis

    1 Answer

    My windshield wipers do not turn on


    Hello,

    Check you fuse panel. This would be the easiest way as it's either the wiper motor, wiper switch or a fuse. Your car should have a schematic of what fuse is for what function, if not you can Google it. You can also pic up a repair manual for about $15-$20 at any local parts store too. Parts are pretty cheap and it's probably the fuse or the interior wiper control switch as wiper motors rarely ever die. Good luck.

    Mar 02, 2015 | 2001 Kia Sephia

    2 Answers

    I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


    The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
    The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
    Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
    Visual Inspection Chart Mechanical Electrical
    • Windshield washer pump hoses
    • Windshield wiper mounting arm and pivot shaft
    • Bussed electrical center (BEC) fuse 10 (30A)
    • Smart junction box (SJB) fuse 3 (10A)
    • Circuitry
    • Windshield wiper motor
    • Windshield washer pump
    • Windshield wiper/washer switch
    • The wipers stay on continuously
    • Circuitry
    • Windshield wiper motor
    • Windshield wiper/washer switch
    • Go To Pinpoint Test C .
    PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
    Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
    • Key in OFF position.
    • Disconnect: Windshield Wiper/Washer Switch C2137.
    • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
    • Does the windshield wiper/washer switch pass the component test?
    Yes
    GO to C2 .

    No
    INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
    • Disconnect: Windshield Wiper Motor C125.
    • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

      Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

      s6b~tr~en~file=n0011980.gif~gen~ref.gif
    • Are the resistances greater than 10,000 ohms?
    Yes
    GO to C3 .

    No
    REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
    • Disconnect all the windshield wiper motor connectors.
    • Check for:
      • corrosion.
      • pushed-out pins.
    • Connect all the windshield wiper motor connectors and make sure they seat correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present?
    Yes
    INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

    No
    The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
    You

    Feb 20, 2015 | 2007 Ford Mustang Coupe

    2 Answers

    How do you replace windshield wiper motor on a 1997 ford e250 van


    REMOVAL
    1. Raise and support the hood.
    2. Remove the windshield wiper pivot arms.
    3. Remove the cowl top vent panels.

    25287270-15uk5heqgoha5mc4ejw3dmql-1-0.gif
    1. Disconnect the windshield wiper mounting arm and pivot shaft.
    1. Remove the access cover from the dash panel.
    2. Remove the mounting arm and pivot shaft retaining clip.
    3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

    25287270-15uk5heqgoha5mc4ejw3dmql-1-2.gif
    1. Remove the windshield wiper motor.
    1. Disconnect the electrical connector.
    2. Remove the three bolts.
    3. Remove the windshield wiper motor.
    INSTALLATION

    25287270-15uk5heqgoha5mc4ejw3dmql-1-5.gif
    1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

    25287270-15uk5heqgoha5mc4ejw3dmql-1-9.gif
    1. Install the windshield wiper motor.
    1. Place the windshield wiper motor in the dash panel.
    2. Install the three retaining bolts.
    3. Reconnect the electrical connector.

    25287270-15uk5heqgoha5mc4ejw3dmql-1-14.gif
    1. Reconnect the windshield wiper mounting arm and pivot shaft.
    1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
    2. Install the access cover in the dash panel.
    1. Install the cowl top vent panels.
    2. Install the windshield wiper pivot arms.
    3. Adjust the windshield wiper pivot arms.
    This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

    Nov 17, 2014 | Cars & Trucks

    1 Answer

    How to change Windshield Wiper Motor Pulse Board on 2005 chevy impala


    Change the wiper motor, and you replace the pulse board.. You can not buy the board separate from the motor.

    Aug 07, 2014 | Chevrolet Chevy Cars & Trucks

    1 Answer

    My 2003 PT Cruiser has windshield wipers in the front for front windshield but also one windshield wiper in the rear for the back windshield. The wiper in the rear is operating fine but my front ones do...


    More than likely you need to replace the front windshield wiper motor. You should unplug the motor and check the plug for voltage, checking each terminal as you change the speed selection on the switch. This should help determine if it is a power problem, switch problem, or motor problem.

    Aug 18, 2011 | Chrysler PT Cruiser Cars & Trucks

    1 Answer

    Windshield wipers won't work


    Have you checked the fuse? That would be the easiest fix if thats was it. If the fuse is not the problem then you probably need a new windshield wiper motor. It would be in between the two wipers along the top of the firewall. Shouldn't be to hard to switch out. Check the fuse first though cause that could be all you need.

    Dec 30, 2010 | 2004 Ford Thunderbird

    1 Answer

    The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


    why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

    What happens when you activate the washers?

    go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


    don't have 1983 info, but here is 1994:

    Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
    DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
    ------------------------------------------------------------------------------------------------
    Pivot Shafts and Linkage Removal and Installation
    NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
    1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
    1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
    1. Remove left windshield wiper adapter and connecting arm clip access cover.
    1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
    ----------------------------------------------------------
    Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
    1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
    1. Disconnect battery and wiper motor electrical connector.
    1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
    1. Disconnect the battery ground cable (14301).
    1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
    1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
    1. Reach through the access cover opening and unsnap the wiper motor clip.
    1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
    1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
    1. Remove nut and ground strap.
    1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
    Installation
    1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
    1. Install nut and ground strap.
    1. Connect wiper motor electrical connector.
    1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
    1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
    1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
    1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
    1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
    1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
    1. Test the system.
    6bd608c.gif

    Jan 04, 2010 | 1983 Ford Ranger

    1 Answer

    Need to get a programmer dont know where its at


    • Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
    • Damaged turn signal and windshield wiper switch .
    • Damaged windshield wiper motor .
    • Damaged windshield wiper control module.
    7fd52e7.gif
    efd7dbe.gif
    Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
    Windshield Wiper System The windshield wiper system consists of :
    • Windshield wiper motor (17508) (F-type).
    • Washer system.
    • Windshield wiper control module.
    • Turn signal and windshield wiper switch (13K359).
    The windshield wiper control module is:
    • Located at the instrument panel fuse panel.
    The windshield wiper motor is:
    • Attached to the cowl top extension (021A36) .
    • Connected to windshield wiper mounting arm and pivot shaft (17566) .
    The turn signal and windshield wiper switch features a:
    • Rotary wiper switch.
    • Push type washer actuator.
    OFF/Low/High Speed
    • Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
    • The windshield wiper motor has a brush rigging that permits selection of low or high speed.
    • When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
    • When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
    • In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
    • When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
    • When the park switch contacts open, the windshield wiper motor stops in the park position.
    Interval
    When the turn signal and windshield wiper switch is in the interval position:
    • The wipers make single wipes separated by pauses.
    • The rotary switch is on the end of turn signal and windshield wiper switch .
    • The length of the pause can be set from approximately 1 to 17 seconds.
    • Length of pause decreases as the rotary switch is rotated away from off.
    • Length of pause increases as the rotary switch is rotated toward off.
    While in the interval wiper mode:
    • It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

    May 27, 2009 | 1994 Ford Mustang

    2 Answers

    Front wipers stopped working but you can hear the motor run also


    If the wipers were buried under snow/ice or frozen to the windshield, you may have blown the red 10 amp fuse located in cavity 9 in the fuse block located on the bottom left side of the instrument panel near the parking brake pedal.
    In order of easiest to check:
    1) ensure wipers not frozen to windshield.
    2) ensure wiper arms are not loose on the pivot stud,
    3) check the red 10 amp fuse.
    You stated that "you can hear the motor". Which motor do you hear? The engine or the wiper motor?
    If you hear the wiper motor, then the fuse is alright. Try 1) and 2) above.
    PT Stanley

    Jan 20, 2009 | 1998 Dodge Grand Caravan

    Not finding what you are looking for?
    1993 Chevrolet Camaro Logo

    Related Topics:

    186 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    64034 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21990 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...