Question about Hyundai Motor 1998 Accent

1 Answer

Alarm system on hyundai xg350

My car battery exploded and the alarm system wont stop,i bought a new battery and each time I connect the battery,the alarm wont goes on I dont know where the alarm button is.some one pls help.

Posted by on

  • kyky42net Feb 10, 2009

    thks dude, i did it worked,but the problem is the light cant turn on,the signal light aint working,the trunk cant pump,the fuel injector ant open to fill gas,the radio dont work,the window cant roll down,everything messed up.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 141 Answers

Disconnect the the alarm speaker by taking one end of the speaker inside engine compartment, it looks like horn, follow wires and look for one of both (any) and cut it or disconnect if You find terminals, Your Relay is the problem, or your switch

Posted on Feb 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alarm randomly going off remote will turn itboff but few mins later starts again


Hyundai XG350 alarm module Questions & Answers - Fixya

www.fixya.com > ... > Tags > alarm module > Cars & Trucks > Hyundai
Hyundai XG350 cars & trucks alarm module questions and answers. Ask your Hyundaialarm ... TURN IGNITON TO ON 4. WAIT 5 ... Hyundai Motor 2005 XG350.

Aug 27, 2015 | Hyundai Motor 2005 XG350

2 Answers

How do I enable a factory alarm on my car?


What do the user manuals for the car and alarm have to say? Have you asked the manufacturer?

May 06, 2015 | 2002 Hyundai XG350 L

2 Answers

I have a 2003 hyundai sonata and i dont have the remote for the stock alarm. My alarm keeps going off and my car wont start. I bought a new battery and even tried the key in the door still no luck.....


The 2003 Sonata is equipped with a 'starter KILL' burglar alarm system with disables the starting system (using a N/C 'contacts' configuration instead of a N/O contacts configuration). N/C=Normally closed, and N/O=Normally open contacts. When the alarm goes off with a MY Sonata, the only way to DISARM it is with the key fob (remote) originally programmed for it (unless you purchase a new remote & have it programmed for the vehicle at an authorized Hyundai Service Department). NOTE: So long as the keyless entry & burglar alarm system is functioning/operating normally, the alarm will keep going off and the STARTER KILL function will still prevent you from starting the vehicle. One option is left without purchasing a new remote and having it programmed.
1. When the alarm goes off, get into the vehicle and insert the ignition key into the ignition.
2. Turn the key to the 'RUN' position (NOT the ACC position) and wait for the alarm to STOP (usually about 3 to 5 minutes).
3. The engine should then start using the ignition key.

If this procedure doesn't work, the problem will need further diagnosis by a qualified/certified Hyundai Service Technician.

Hope this helps

Aug 27, 2011 | 2003 Hyundai Sonata

1 Answer

I need to know how to replace a water pump on a 2002 hyundai gx 350.


2002 Hyundai XG350 3.5L MFI DOHC 6cylWater Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Accessory drive belts Water pump pulley Timing belt, tensioner and idler pulley Water pump

  4. 1514f36.jpg

    Fig. Water pump assembly-XG 300 and XG 350 (click over pic for zoom)

To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.
To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.

95486b3.jpg


Fig. Water pump bolt lengths-3.5L engine

Install the water pump with new gaskets and O-rings. Tighten the bolts to the following specifications:
  1. 1.5L SOHC engine: 105-132 inch lbs. (12-15 Nm).
  2. 1.5L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  3. 1.6L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  4. 1.8L, 2.0L, and 2.4L engines: 14-20 ft. lbs. (20-27 Nm).
  5. 2.5L engine: 11-16 ft. lbs. (15-22 Nm).

Hope helps (remember rated this).

Jun 18, 2010 | 2002 Hyundai XG350

1 Answer

2003 hyundai xg350. Starts and runs, then cuts off.


Ita an imobilizer fault.Try changing the key fob battery first.Before having it reprogamed.

Jul 07, 2009 | Hyundai Motor 2003 XG350

2 Answers

Program factory remote keyless entry: 2003 Hyundai XG350


The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

May 22, 2009 | Hyundai Motor 2003 XG350

1 Answer

Program factory remote keyless entry 2003 Hyundai XG350


I've informed you of what you need to do. Take the veh into a Hyundai Service Center - let them program the remotes.

May 22, 2009 | Hyundai Motor 2003 XG350

1 Answer

Programming factory remote on 2003 Hyundai XG350


Again, the remotes can only be programmed by a Hyundai Technician (ETACS - Electronis Time and Alarm Control System).

May 22, 2009 | Hyundai Motor 2003 XG350

1 Answer

2003 Hyundai XG 350 will not start


Hooked new battery up, alarm went off, waited until it stopped, locked car with fob then unlocked and the car started.

Dec 15, 2008 | 2002 Hyundai XG350

Not finding what you are looking for?
Hyundai Motor 1998 Accent Logo

432 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...