Question about 2002 GMC Sierra C/K1500

1 Answer

Windshield wiper motor

Where is the location of the wind shield wiper motor on gmc yukon xl 1500?

Posted by on

  • Anonymous Mar 27, 2014

    wiper relay location

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 202 Answers

Under the plastic cowl that the windshield wipers are on top of. removal of the wipers is nessecary. then removal of the cowl is next. and underneath all that should be the motor.

OR sometimes it is mounted on the firewall in the engine bay on either side usually can't miss it.

Posted on Feb 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the cam shaft location sensor located on a 2005 gmc yukon


camshaft sensor located above crankshaft pulley, the camshaft sensor mounted on the front timing cover above the crankshaft pulley.

Sep 17, 2012 | 2005 GMC Yukon

1 Answer

I have checked the wind shield wipers motor to try to find out what is shorting out the fuse. Where could the short be located that is causing the wiper fuse to blow?


You need to isolate the problem by disconnecting the windshield wiper motor. If the fuse does not blow with the wiper motor disconnected the problem is in the windshield wiper motor. If the fuse still blows with the motor disconnected, there is a 12 volt wire shorted to the frame. You will most likely need a set of wiring schematics to trace down the short.

Mar 21, 2011 | Hyundai Accent Cars & Trucks

1 Answer

Where is the wiper motor on a 2002 gmc sierra? Have used motor to replace it. May only be pulse board, but this was the advised solution.


I am assuming the truck is alot like my 2001 yukon. If that is the case, then the wiper motor is underneath the plastic cowl in front of the windshield. Mine was held on by 4 clips on the front and one screw on each side of the vehicle (driver/passenger). Wiper arms will need to be removed and will most likely need a wiper arm puller tool.

Dec 23, 2010 | 2002 GMC Sierra 1500

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

2001 GMC Yukon XL


YOU CAN GO DEALERSHIP OR THE SALVAGE YARD PROBABLY HAVE A WASHER FLUID TANK AND HOSES IN GOOD SHAPE.

Mar 23, 2010 | 2001 GMC Yukon XL

2 Answers

Windshield stops intermitently


2 causes wiper switch out or motor bad. Most common is the wiper muti function switch.

Jun 29, 2009 | 1998 GMC Jimmy

1 Answer

Help, please! My wind shield wipers will no turn off.


There is a fuse for the wiper motor take it out. Sounds like the multifunction switch for the wipers has malfunctioned.

Mar 25, 2009 | 2003 Chevrolet Suburban 1500

1 Answer

99 Yukon windshield wipers sometimes won t turn on and other time stop after working


We had the same problem and sometimes they wouldn't turn off. The intermittent wipers were random. We replaced the wiper motor. Be sure to get the motor with two balls on the wiper shaft (one for each wiper arm). If you can't find it, you'll have to change the part out on the new motor. Keep the wiper arms in the same location on removal, or it will jam and you'll have to start over.

Jul 14, 2008 | 1999 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

420 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...