Question about 1997 Buick LeSabre

1 Answer

Will not start

Just had plugs and wires put on now car will turn on but will not start

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 373 Answers

It could be the cap and rotor or fuel pump or fuel filter

Posted on Feb 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 cavalier turns over wont start plugs were no good put new plugs in used dielectric grade on plugs still won't start could I have put to much dielectric grease on plug wires


Trying to start the vehicle is there spark ? Your vehicle has plugs under center of valve cover .Pull the coil pack out , get plug wire cable set and use a spark tester . Check for spark . If plugs were no good you probably fried the ICM - ignition control module . Do you know what and where ICM is ? How to Test the Ignition Coils GM 2 4L Quad 4 The amount of dielectric grease has nothing to do with it .

Jan 05, 2017 | 2005 Chevrolet Cavalier

1 Answer

1994 Toyota 4Runner turns over, but won't start.


Could be so many things... I put a wire from the positive on battery to the glow plug rail, there is a plug push the wire in so the glow plugs are hot wired and try to start. Other wise try the usual and bleed it?

Dec 27, 2010 | 1994 Toyota 4Runner

1 Answer

2004 mazda wont start, blew a front tire and had to be put on rollback. Sat all nite, and now wont start. will crank and can smell fuel.


flooded engine common problem remove all plugs and fuel pump fuse. get fuel out of engine do not istall fuel pump fuse re install all plugs I suggest a good charger be used as system can kill batt very quick run to wires from fuel pump fuse into seating area start cranking the engine over wires not touching once compression sounds alright touch wires to geather (may have to repeat these deflooding wire touching procedure many times) once started do not turn off car till normal operating temp . Once hot turn car off remove wires and re install fuel pump fuse .With RX-8 u cannot just start and stop car right away as in washing car as it can produce this same condition ALWAYS let car warm up before turning off.

Oct 18, 2009 | 2004 Mazda RX-8

2 Answers

Need to start a car 1965 mustang that has not been started in 5 years what should i do first. iI have no idea whats wrong with it.


change old oil and filter make sure all spark plug wires are there and look ok take spark plug out and pour little amounts of marvel mystery oil down into cyl. then turn engine over acouple times if it has a oil pressure guage make sure with spark plugs out and engine turning that you have some oil pressure.then take some fuel line and connect it to the fuel pump on the side of the engine you most take off line going to the fuel tank in order to do this then put all but one spark plug back in the put all the wires on then the one plug that you left out check for spark by installing the wire on the plug and setting the plug on something metal on the car (grounded) the turn the engine over and look if the plug is making a spark if so put it all back together. then with that line you put on the fuel pump stick it into a gas can with plenty of fuel then pour a tiny amont into the carb and try to start

Oct 15, 2009 | 1965 Ford Mustang

1 Answer

Will not start. 1995 astrovan will not start. engine turns over as normal, sounds like it is starving for fuel or spark.


pull a spark plug wire off at spark plug put another plug in wire lay plug and wire against metal of engine and turn motor over looking at plug for spark. as for pump noise turn key on not to start and listen for whine noise for a couple seconds. if hear whine that is your fuel pump noise. not a clear filter canister about under drivers seat on inside of fram

Sep 07, 2009 | 1995 Chevrolet Astro

1 Answer

Wont turn over something with the wire for the chip in the key 95 buick regal custom wire was rigged up with a fusible link and the wire from cylinder wasnt even plugged in then the wire with the fusible...


Buy a new cylinder, put old chip key in cylinder, now plug into the connecter and hide under dash. Start car with with second or duiplicate key. Or measure the resistance in chip on key and get a resistor from radio shack and connect it to wire that plugs in to lock cylinder

Jun 18, 2009 | 1995 Buick Regal

2 Answers

2001 Dodge Strutus will not start


yes it could be the ignition switch.

Apr 28, 2009 | 2001 Dodge Stratus

2 Answers

I need to change the spark plugs and i dont know where to start?


Go through your spark plug wires and mark which plug it is on. Once you have done this then you can pull the wires off each spark plug. Once the plug wires are off take a spark plug socket and gently apply some pressure to loosen the spark plug. Once its loose you should be able to reach down and remove the plug by hand. Once you have the plug off grab your new plug. Make sure it has the correct gab setting for your engine size and then install the new plug. once you have the new plug in gently snug it down. Do this with the rest of your plugs. Once all your plugs are in place and snugged down then put your plug wires back on each plug (This is where the labeling comes in handy). It is also a good idea to get a good set of plug wires and just replace them while you are at it.

Apr 01, 2009 | 1987 Ford Bronco

1 Answer

1989 Honda Prelude won't start


I suspect that your spark plug wires or your distributor is going out. Check your spark wires and distributor. To do that take out #1 spark plug wire from the spark plug. Next take out your spark plug then put it in the spark plug wire. Then turn on car and take a look at the spark plug to see if it's getting a spark. Do this with all the spark plug. If it is your spark plug wire I would replace all of them.

Jan 31, 2009 | 1989 Honda Prelude

Not finding what you are looking for?
1997 Buick LeSabre Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...