Question about 1989 Ford Ranger

1 Answer

89 Ford Ranger Carrier bearing

How do you install a Carrier bearing on an 89 ford ranger. does it have to be pressed on or what?

Posted by on

  • Anonymous Mar 04, 2009

    Duh? Carrier Bearing on "drive shaft"? not the rear carrier

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 60,867 Answers

All the bearings for the rear diff are pressed off and on, they can be done at home if u have a high quality bearing puller, but to press them on should be done at the machine shop.

Posted on Feb 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where the oik sending switch is on my 89 ford ranger 2.9


It's mounted on the driver's side of the engine block

Jul 27, 2015 | Ford Cars & Trucks

1 Answer

How do you change motor mounts on a 1990 Ford Ranger 2.3


Ford Ranger 2.3 rebuild part 3 "xTUPID BOLTS" - YouTube

? 2:55
www.youtube.com/watch?v=ZJ1jFK4weUE
Mar 28, 2011 - Uploaded by DirTyOhGee
89 Ford Ranger 2.3 Custom/Limited. Moving right along here, ...How to change the timing belt on a Ford 2.3L engine. - Duration: 29:59. by ...

Oct 05, 2012 | Ford Ranger Cars & Trucks

1 Answer

Transmission install 89 ford ranger


You should be able to rent a spline alignment tool from the parts house where you got transmission. I'm assuming you have a manual transmission so the clutch pad doesn't want to cooperate? I think even with an automatic it's much the same.

Jun 15, 2012 | 1989 Ford Ranger

2 Answers

1995 Ford Ranger whines. Three mech's, fuel pump, carrier bearings, wheel bearings. Who is closest?


You need to post the symptoms of your problem. And let us tell you what we think. But for what its worth here I go. Electric fuel pumps howl or moan. Carrier bearings on make noise when vehicle is moving down the road and make a squalling noise when the bearing is going bad but may be interpreted as a whine. Wheel bearings near the same as carrier bearings but they usually grind. So my guess is alternator or pulley bearing since they whine.

Mar 04, 2011 | 1995 Ford Ranger Supercab

1 Answer

Ford ranger 2001 2.3 Ihave to replace the thermostat, What is involved/


2001 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl
  1. Drain the cooling system.
  2. Disconnect the radiator hose and the electrical connector.
  3. Disconnect the radiator lower hose.
  4. Remove the bolts and the thermostat housing.
  5. To install, reverse the removal procedure. Tighten the housing bolts to 89 inch lbs. (10 Nm).

Hope helps (remember to rate and comment this).

Oct 01, 2010 | 2001 Ford Ranger Regular Cab

1 Answer

I have an 89 ford ranger 2.9 engine. The engine


Have the fuel pressure checked,and replace the fuel filter first,it is most likely one of the two causing the problem,if this was helpful,please rate,thank you.

Jun 15, 2010 | 1989 Ford Ranger

1 Answer

Low oil pressure on guage of my 89 ford ranger 6 cylinder


Could be low oil level, a bad sending unit, or actually low oil pressure due to a worn oil pump or worn bearings.

Mar 09, 2010 | 1989 Ford Ranger

1 Answer

Will '89 Ranger leaf springs fit a '99 Ford Ranger 4x4?


Measure the distance from bolt to bolt, and to the center. If they match then, they match, if not you will have to check the numbers with fords tolerances to avoid an axle wrap. But it should fit, maybe just a little stiffer of a suspension from the 4x4.
Calvin the Mobile Mechanic.

Mar 15, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Torque specs 7.5 inch rear axle 96 ford ranger


Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Jan 30, 2009 | 1996 Ford Ranger SuperCab

2 Answers

I paid for an answer about my 89 ford ranger drive shaft and did not get one. Can I get my money back or do I need to contact Pay-Pal??


To replace the centre bearing you first remove driveshaft from vehicle.
Pull the shaft apart at the middle universal joint.
On the back of the section that has the centre bearing you will see a nut that holds the uni ears onto the shaft.
Undo the nut and remove the ears. Then press the centre bearing off the shaft and reassemble with new one.
Hope this is more helpful.

Jan 01, 2009 | 1991 Ford Ranger Supercab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

412 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...