Question about 1998 Toyota 4Runner

1 Answer

98 4runner spark plug wire order

Dont no order

Posted by on

  • podbot999
    podbot999 May 11, 2010

    Hi what engine does it have fitted?

    4cylinder

    6 cylinder

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 130 Answers

Any tune up specs you need can be found on autozone.com hope this helps

Posted on Feb 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installing Spark plug wires


Unless the wires were removed the firing order cannot change as also the length of the wires do not permit that the wires switch over.
All what is needed is to check the spark at each plug , if of low internsity check the ignition system including the HT coil. Also the fuel filter and the fuel pump for the right pressure.

Nov 22, 2011 | 1996 Honda Accord

2 Answers

My spark plugs in my 2004 Mitsubishi Endeavor needs to be changed, and my husband wants to do it himself so is there some way to give me some instructions on how to change spark plugs for my 2004...


YOU NEED LONG SPARK PLUG SOCKET. NEED A 3/8 INCH RATCHET WRENCH.YOU NEED EXTENSION.YOU NEED SPARK GAUGE YOU NEED A TORQUE WRENCH. NOT MANDATORY JUST DONT OVER TIGHTEN SPARK PLUGS STRIP ALUMINUM THREADS WAIT UNTIL ENGINE COOL TO KEEP FROM WARPING THE HEADS. SPARK PLUGS LOCATION ON TOP OF CYLINDER HEADS.TO GET TO SPARK PLUGS THE COILS ON TOP EACH SPARK PLUG.HAS TO BE REMOVED BY REMOVING SMALL SCREW.THAT HOLD COILS DOWN.AND CHANGE ONE SPARK PLUG AT A TIME SO YOU WONT GET THEM MIXED UP.GAP PLUGS AT 0.028 - 0.031

Jan 28, 2011 | Mitsubishi Endeavor Cars & Trucks

2 Answers

I dont know in what order my spark plug wires hooked up.


Chec here the MUSTANG FIRING ORDER

Below are the firing orders for 5.0L, 4.6L, 3.8L, and 2.3L late model Mustangs. Remember to be very careful when checking your firing order because the ignition system on your car runs on very high voltage. Do not remove spark plug wires from the distributor or spark plugs while the engine is running.
Firing order sequences:
V8's 1-3-7-2-6-5-4-8
V6's 1-4-2-5-3-6
2.3L 1-3-4-2

bcd56b8.jpg


Hope this help (remember comment and rated this) TY for using Fixya.

Apr 30, 2010 | 2005 Ford Mustang

2 Answers

Do a tune up


You'll need to remove in take manifold to get to the spark plugs.

Jan 08, 2010 | 2000 Mitsubishi Montero Sport

1 Answer

I dont know how to change the sprak plugs and is very expencive, please help, I broke and I want to do it my self


its not that hard al you got to do is get a spark plug socket there is going to be two sizes your going to need the smallest one and just follow the spark plug wires to the spark plugs and then take them out but make sure you put the new wire on right when you take the old one off so you dont mess up the fireing order

Nov 05, 2009 | 1996 Plymouth Grand Voyager

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

1 Answer

Spark plug replacement


after purchasing replacement spark plugs and wires and making sure to have them correctly gapped use a 5/8 spark plug socket remove one at a time and replace in that order to make sure you dont mess up firing order gently remove boot on the first plug then unscrew plug place new plug in secure wire by snapping boot onto plug if theres oil in your cylinder youll need to replace tube seals common problem with hondas seal kit comes with valve cover gasket its fairly simple.
replace all of them the same way one at a time.

Feb 20, 2009 | 1998 Honda Accord

1 Answer

Firing order


If you pulled all the wires at once, you will need to go to a parts store and see if they can show you a diagram on how to reset the wires. Do not unhook the wires from the spark plugs at this point.

Feb 14, 2009 | 1987 GMC VanDura

2 Answers

Ihave changed the spark plugs but i dont know if put the caps in


Not sure what you're asking. The only order that matters is the order of the spark plug wires. There isn't an order for the spark plugs themselves. So are u looking for the order of the spark plug wires?

Nov 12, 2008 | Honda Civic Cars & Trucks

1 Answer

Changing spark plug wires


WEll u dont need to remove anything This is what i did lift your car up with a jack. where you oil filter is you will see you plug wires running into your (ICM) Ignition Module unplug them and slide them to the top of your motor. dont get them mixed up otherwise your timeing will be messed up and your car wont start. on the ICM from the top to bottom the plug numbers are 2,3,1,4 and on top of the moter from left to right 1,2,3,4 just make for sure u have the right order..

Aug 28, 2008 | 1995 Pontiac Sunfire

Not finding what you are looking for?
1998 Toyota 4Runner Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...