Question about 2001 Isuzu Rodeo

2 Answers

Having problem pulling cv axle

01 izusu rodeo is there a easy way to get out cv axle

Posted by on

  • j_seavy May 11, 2010

    what exactly are you having trouble getting out. should be pretty
    simple, pull the hub off, and remove the axle. try a prybar to help pop
    the axle out of the housing

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 13 Answers

The front axle assy. is basically the same as the older ones. but....u can remove the hub....and spindle assy.....cut the big clamp on the inner boot.....im assuming your replacing boot kits.....pull boot back and slip small screw driver in there....there is a large this round low tension c lip in there.....then u can pull outer joint and axle and most of inner joint......replace the boots......fill inner boot with grease and reassemble.....time consuming but not real bad to do.

Posted on Feb 15, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 25 Answers

From the front? If so no there is no easy way to do so. I had to drop the differental and then remove the cv shaft.... but this was on a 1993 I would think its still the same...

Posted on Feb 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Isuzu rodeo troubleshooting


Sounds like a ball joint seeing that the cv joints were replaced, have you had it aligned?

May 07, 2014 | 1998 Isuzu Rodeo

1 Answer

How to remove both front cv axles from front diff, i have every thng off and this aint my first rodeo, so whats up with getting the inner cv joint out of the diff.


If you have everything loose so the CV axle will pull out of the diff, try this: Using two flat head screwdrivers, put them beteween the inner edge of the joint and the diff. GENTLY pry with both screwdrivers 180 degrees apart ( like at 3 and 9 o'clock). there is a clip in a groove that has to retract al the way in to release the halfshaft. It can be very frustratiing as I have been there done that. try rotating the axle about a quarter turn and then use the two screwdrivers again. some times you just have to find the "sweet spot".

Jul 24, 2011 | 1998 Isuzu Trooper

1 Answer

Removing a drivers side cv joint on a 95 holden rodeo?


You have to remove the wheel then take the brake caliper off remove the nut from the upper control arm drop it down using a tye rod remover take nut off cv joint then use a pry bar to pop the cv joint from transmission now pull out of axle and remove.

Nov 29, 2010 | Isuzu Rodeo Cars & Trucks

1 Answer

How to put on right front cv axle and both lower ball joints and idler arm.


Bring it to your mechanic this is not easy you need to take the wheel off
unbolt the axle if you can get the axle out without taking off the ball joints than do so but usually you will need a big set of tools and special puller for the idler arm. Make sure you disconnect the abs sensor or wire going to your brakes take center bolt out of center of rotor take ball joint nuts off.You need a ball joint seperater.Only use on junk ball joints.
Pull rotor assembly and caliper braket and rotor off in one peice be carefull not to break the brake lines to the caliper.If you are going to attempt this it can lead to serious bodily injury it should be done by a mechanic.After this is done unbolt cv axle from axle transfer case/transmition.The ball joints need a press and may need to be heated to get out of control arm.Bring it to a mechanic or met a nice guy that will do it cheep

Jan 15, 2010 | 1993 Isuzu Rodeo

1 Answer

I have a 1999 isuzu 4wd rodeo 6 cylinder and was wondering if Need to install a new boot kit or if I need to replace the entire front left cv axle shaft. I had a tear in my rubber boot and noted some...


Do not try to get the cv axle out ot the axle housing. It is a major operation. Remove boot and disconnect the inner cv joint and save about five hours of time. The choice is yours ,boot or reman cv axle. You will need to take the reman. axle apart to install it though and some new clamps. Not a simple operation.

Sep 28, 2009 | 1997 Isuzu Rodeo

1 Answer

Trouble getting marks aligned on 2001 Izusu Rodeo


if its a 6VE1 engine you might want to remove rocker covers and put front lobes of camshafts in position shown in picture with cam gear timmed up at same point cam gear are 3:1 ratio


b76b855.jpglook closely at cam gears in pic to see front lobe positions for both banks

Jul 29, 2009 | 2002 Isuzu Rodeo

1 Answer

Cv joint removal


Get the replacement cv axle and remove inner boot and clip and bearings. Do the same on the old axle. Replace bearing clip, cv shaft and reassemble. Do not try to remove the part from inside the front axle unless you want to spend about six hours of time and money.

May 12, 2009 | 1999 Isuzu Rodeo

1 Answer

New cv axle


you dont have to take off the hub. just take off the strut where is connects to the steering knuckle and twist it out of the way and take the axle out that was. you may also have to take the tire rod off the knuckle also. and if you wanted to make it really easy then you could that the whole knuckle off the ball joint and just pull the cv axle straight out.

Mar 29, 2009 | 2000 Suzuki Esteem

Not finding what you are looking for?
2001 Isuzu Rodeo Logo

524 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...