Question about 2001 Toyota Corolla

1 Answer

Replace front wiper motor

I can obviously get at the motor easily, how do I get at rear to disconnect/connect the rods.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

You pull the motor out, and access the linkage bolt after that.

Posted on Feb 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the wiper motor on a 98 rodeo


the front or rear, no way for me to guess?????
unbolt it and replace it.
start at the arms and work inward works.

ill toss coin land on front.
ill read the FSM online for you, so can you , but here ill do it.

Motor
  1. Disconnect the negative battery cable.
  2. Disconnect the wiper power motor connector (2).
  3. Remove 4 mounting bolts.
  4. Remove the nut of the wiper motor shaft, and disconnect the linkage.
  5. Remove the windshield wiper motor (1).
To facilitate the removal of the nuts, be sure to put out the tip portion of the linkage sufficiently through the mounting hole of the motor by sliding the wiper blade slowly.


my guess is this the most easy motor on earth to change.
its in plain view, not burried deep in a cowl.....

it's
easy-peasy-japanesy..

Feb 22, 2015 | 1998 Isuzu Rodeo

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

2 Answers

How do I dismantle and reinstall a front wiper motor on a 2000 Kia Sportage?


moz-screenshot-6.pngmoz-screenshot-7.pngplay0027.gif
Wiper Motor

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the wiper motor electrical connector.
  3. Remove the four mounting bolts securing the motor to the firewall.
  4. Using a suitable prybar, carefully separate the wiper motor from the wiper linkage and remove the motor.

To install:
  1. Attach the wiper motor ball joint to the wiper linkage.
  2. Position the motor on the firewall and secure the motor with the four mounting bolts. Tighten the mounting bolts to 75 ft. lbs. (102 Nm).
  3. Connect the electrical connector.
  4. Connect the negative battery cable.play0027_0.gif

moz-screenshot-8.png

Nov 25, 2010 | 2000 Kia Sportage

1 Answer

I need to know how to remove the pannel cover on the rear hatch door I can get to the rear wipper motor


449b69b.jpg

Exploded view of the Explorer/Mountaineer rear liftgate trim panel (click for zoom)



Rear Window Wiper Motor


b5927f1.jpg

Fig. : Rear wiper motor assembly and related components

  1. Disconnect the negative battery cable.
  2. Remove the wiper arm and blade.
  3. Remove the liftgate interior trim.
  4. Remove the motor attaching bolts (3). Disconnect the electrical leads.
  5. Remove the wiper motor from the vehicle.
To install:
  1. Install the wiper motor in position and connect the electrical leads.
  2. Install the liftgate trim. Connect the negative battery cable.

I hope helps (remember to rate this).

Oct 11, 2010 | 1996 Ford Explorer

2 Answers

How do I fix my window washer pump on my 2000 dodge caravan?


One can get a repair kit that includes a new motor pump and wiring clips, or

one can get the original motor that plugs into the windshield wiper fluid reservoir.

---
Windshield wiper reservoir (gives idea of how to change the windshield wiper fluid pump motor) Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and splash shield.
  4. Disconnect the electrical connectors from the pumps and detach the rear washer hose.
  5. Place a drain pan under the reservoir if it contains fluid.
  6. Disconnect the front washer hose at the wiper unit in the engine compartment. NOTE: The front hose will be removed with the reservoir.
  7. Let the fluid drain from the reservoir.
  8. Remove the mounting screws and the reservoir.
To Install:
  1. Install the fluid reservoir with the mounting screws.
  2. Connect the front washer hose in the engine compartment.
  3. Connect the electrical connectors and rear washer hose.
  4. Install the splash shield.
  5. Install the right front wheel.
  6. Lower the vehicle.
prev.gif next.gif

Aug 27, 2010 | 2000 Dodge Caravan

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

Front wipers not moving after heavy snow woper blades disconnected from motor where is the moter located


the pivot point for the blades are connected to connection rods, usually under the hood or a covered section between the windshield and the engine compartment. the motor can be in that same space or on the firewall (back of the engine compartment) with the shaft through the firewall and attached to the wiper connection rods. The rods my have come lose from the pivot points or the connecting rods may have come lose from the motor shaft or the splined connection may have "stripped."

Jan 10, 2010 | 2003 Nissan Pathfinder

1 Answer

My front wipers do not work, the washer on the front and the rear wiper works fine, they are all on the same thing


HI. This is a possible motor issue. To confirm, use this procedure. it will help isolate the actual issue at hand.

1.Make sure the battery has a strong charge and is in good condition. Use a voltmeter to get a reading if necessary.

2.Connect a jumper wire between ground and the wiper motor. Turn the key on but don’t start the engine. Turn the wiper switch on. If the motor works, check for a corroded or loose ground connection.

3.Turn on the car key but don’t start the engine. Turn on the wipers. Check for voltage at the wiper motor with your voltmeter. If you get a good voltage reading, turn the key off and disconnect the motor from the wiper linkage.

4.Move the wiper arms by hand. If they are stuck, you have found the problem. If the wiper arms move freely by hand, go to step 5. If voltage is not reaching the motor go to step 6.

5.Remove the wiper motor by disconnecting the plug and removing the bolts using a wrench or ratchet. Use a pair of jumper wires to connect the wiper motor directly to the battery. If the motor does not work, replace it.

6.Turn on the key but don’t start the engine. Get a voltage reading across the wiper switch. If there is voltage, use a jumper wire to bypass the switch, if the motor works now, replace the switch, otherwise go to step 7. If there is no voltage at the switch, go to step 8.

7.Check for continuity at the wire between the switch and the motor. The wire could be loose or disconnected.


8.Check the wire coming from the fuse panel to the wiper switch. It could be disconnected or loose.

Nov 23, 2009 | 2004 Jeep Liberty

1 Answer

2005 ford expedition rear wiper


Sounds like a problem within the wiper motor not turning off at rest or not reaching it's rest point to be able to turn itself off, probably needs a new motor. Disconnecting it should have no relation to the front washer operation, you can confirm this by reconnecting the wiper motor to try.

Apr 12, 2009 | 2005 Ford Expedition

1 Answer

Driver's side wiper arm on my '93 Sidekick is not working


This is what I Found there was not any Illustration's with it looks Fairly simple, Good luck



FRONT
  1. Disconnect linkage assembly from wiper motor shaft.
  2. Disconnect electrical connectors from wiper motor.
  3. Remove wiper motor attaching bolts, then wiper motor.
REAR
  1. Remove wiper blade and arm assembly.
  2. Remove access panel on back door.
  3. Disconnect linkage assembly from wiper motor shaft.
  4. Disconnect electrical connectors from wiper motor.
  5. Remove wiper motor attaching bolts, then wiper motor.
Skill
Level
Mfg.
Warranty
Standard Wiper Motor Labor Replace Front B 0.7 1.0
PLEASE DONT FORGET TO RATE ME Thank You Much

Jan 20, 2009 | 1995 Suzuki Sidekick

Not finding what you are looking for?
2001 Toyota Corolla Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...