Question about 1986 Plymouth Reliant 4 Door

1 Answer

I have a 1986 Plymouth Reliant, 2.5 (engine)

I NEED TO KNOW HOW YU PUT THE PULLEY BACK ON, I THINK IT IS THE TENSIONER/PULLEY FOR THE SERPENTINE BELT. I NEED TO KNOW HOW THE WHOLE THING GOES BACK ON, I JUST CHANGED THE TIMING BELT, AND HAVE GOTTEN THIS FAR???

Posted by on

  • Jeramy Bishop Feb 10, 2009

    I guess the manual from Another Auto parts store, that I recently purchased, isn't enough info! Thank you, this was more helpful!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 1,479 Answers

Auto Zone has an online manual showing how to do the timing belt here, and for the drive belts here (about halfway down the page).

Posted on Feb 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Serpentine belt diagram


Hi there I am technical mechanical and electronic engineer mechanic if you want help you I have to no more information like make and kind

Oct 25, 2015 | 1995 Plymouth Voyager

1 Answer

Serpentine belt


Application:
With A/C


2.image

Kia_Sedona_2002-2006
Accessory Drive Belts

Print


Accessory Belt Routing



0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt routing-3.5L engine


0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt routing-3.5L engine


0996b43f8020700d.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt (A) routing-3.8L engine


Inspection

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.


Removal & Installation

  1. Disconnect the negative battery cable.
  2. Rotate the auto tensioner clockwise to release tension, then remove the drive belt.

To install:
  1. Install drive belt (A). Route the belt over the components in the following order: Crankshaft pulley - A/C pulley - idler pulley - generator pulley - water pump pulley - P/S pump pulley - tensioner pulley.
  2. Rotate auto tensioner arm in the counter-clockwise moving auto tensioner pulley bolt with wrench.
  3. After putting belt on auto tensioner pulley, release the auto tensioner pulley slowly.

    0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Accessory serpentine belt routing-3.5L engine


    0996b43f8020700d.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Accessory serpentine belt (A) routing-3.8L engine


May 09, 2012 | 2006 Kia Sedona 3.8

1 Answer

How simple is it to change a alternator belt on subaru svx?


  1. Removing the Serpentine Belt
    • 1 Park your Subaru on a level surface and open the hood.
    • 2 Disconnect the ground (black) battery cable using a wrench. This will prevent the cooling fan from activating.
    • 3 Locate the serpentine belt routing diagram in your engine compartment and compare it to the actual routing of the installed belt. Make sure the routing on the label matches the actual routing. If they do not match or there is no label, note the actual routing on a piece of paper for later reference.
    • 4 Locate the belt tensioner pulley on your Subaru model. If the tensioner is equipped with a squared hole, use a large breaker bar with a 1/2-inch (13 mm) drive. Otherwise, use a ratchet and socket of the proper size on the tensioner pulley center bolt.
    • 5 Rotate the tensioner pulley away from the belt to release the belt tension.
    • 6 Pull the belt off of one of the pulleys and slowly release the tensioner pulley back into position. Do not let the tensioner pulley snap back or you may damage an internal component.
    • 7 Finish removing the serpentine belt from the rest of the pulleys and the engine compartment.
    Installing the New Serpentine Belt
    • 1 Match the old belt to the new one and make sure they are of the same length and configuration. It is normal for the new belt to be slightly shorter since the old one has been stretched through use.
    • 2 Route the new serpentine belt through all of the pulleys except the tensioner pulley. Use the diagram on the engine compartment or your notes, as a reference, to properly route the belt.
    • 3 Insert the large breaker bar into the square hole or the ratchet and socket into the tensioner pulley center bolt.
    • 4 Rotate the tensioner pulley in the same direction you did to release the belt tension.
    • 5 Slide the serpentine belt onto the tensioner pulley.
    • 6 Release the tensioner pulley back into position.
    • 7 Look at all the pulleys and make sure the serpentine belt is properly seated on each one. Otherwise, release the belt tension and adjust the belt.
    • 8 Connect the ground (black) battery cable using the wrench.

Oct 18, 2011 | 1992 Subaru SVX

2 Answers

Change serpentine belt on 06 sienna


  1. 1 Check to ensure the Sienna's engine is cold, then make sure the Sienna is in park, the ignition is in the off position and the key is removed from the ignition to prevent any possibility of the engine engaging during the serpentine belt replacement.
  2. 2 Open the hood and locate the serpentine belt routing diagram sticker on the side of the engine casing. Study it for a moment before removing the existing belt. It is essential the new belt be installed exactly as the diagram indicates.
  3. 3 Find the tensioner pulley, the main pulley that controls the serpentine belt, and fit a 1/2-inch socket wrench over the self-tensioner on the outside of the pulley.
  4. 4 Pull the wrench to the left to move the pulley forward, which loosens the belt, then remove the belt.
  5. 5 Compare the old serpentine belt with the new, replacement belt for length, width and number of grooves on the belt's underside. Be certain the replacement belt is the right part.
  6. 6 Fit the new belt on to each pulley according to the serpentine belt routing diagram on the manufacturer's sticker, or according to the drawing made prior to removing the old belt. Fit the new belt on to the tensioner pulley last, again applying pressure on the pulley's self-tensioner with the half-inch socket wrench to loosen the pulley.
  7. 7 Release the pressure on the self tensioner and allow the tensioner pulley to ease back into place, thereby tightening the new serpentine belt with the appropriate tension.
  8. 8 Remove the wrench and close the hood.
Thank you and good luck,
Lee

Aug 26, 2010 | 2006 Toyota Sienna

1 Answer

How do i release the tension belt ... cant seem to find bolt being referred to in other docs


Here's the procedure on how to release and replace the tension belt of your car.

Step 1
  • Open the hood on the Volvo S-60 and find the serpentine-belt routing diagram. The diagram should be attached to the top of the fan shroud that covers the radiator. If not, draw out the exact routing method of the serpentine belt around each pulley with a pen and a piece of paper.
  • Step 2 Locate the serpentine-belt tensioner that is in the very center of the engine. The tensioner will have a square bolt head in the center of the tensioner pulley.
  • Step 3 Slide the open end of the 5/8-wrench onto the square bolt head in the center of the belt-tensioner pulley. Turn the tensioner pulley counterclockwise and slide the serpentine belt off of the tensioner pulley.
  • Step 4 Remove the serpentine belt from the other pulleys and pull the belt out of the engine compartment.
  • Step 5 Slide the new serpentine belt into the engine compartment and around the crankshaft pulley.
  • Step 6 Route the new serpentine belt around each pulley. Turn the belt-tensioner pulley counterclockwise again and slide the serpentine belt around the tensioner pulley. Release the tensioner and it will tighten the belt around the pulleys. Look over the belt to ensure that it is inside of each pulley.
  • Step 7 Crank the S-60 and look over the serpentine belt with the motor running. Let the engine run for about one minute and shut the engine off. Close the hood.
  • Aug 12, 2010 | 2001 Volvo S60

    1 Answer

    Replacing serpentine belt


    Click on the following direct Link. It has the Serpentine Belt Diagram that you will need depending on your engine size (2.0L or 3.0L) and your options (AC/No AC ect.).
    http://www.2carpros.com/car_repair_information/year/2001/make/mazda/model/tribute/2001_mazda_tribute_drive_belt_routing_diagram.htm

    Standard Rules to Removal the Serpentine Belt with a Tensioner:
    1. Find the Tensioner(s). (See Diagrams on Link)
    2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    3. Remove the loosened belt off one of the other more easily accessed Pulleys.
    4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.


    Standard Rules for Installing the Serpentine Belt with Tensioners:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

    Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

    Mar 23, 2010 | 2001 Mazda Tribute

    1 Answer

    How do you replace an auto tensioner (serpentine belt pulley) on a 2000 Plymouth voyager?


    take the pressure off the belt and move belt off the tensioner then unbolt it and remove then bolt on the new one then put pressure on tensioner to put belt back on (make sure you see and know how the belt goes back on incase it comes off more than you intended)

    Nov 20, 2009 | 2000 Plymouth Voyager

    1 Answer

    How to replace the drive belt in a mercury grand marquis 1989


    Posted by Asker under the 1992 Mercury Grand Marquis for a 1989 model.

    Sorry for the delayed response....
    I am personally going back to answer your unanswered question.
    I do not know if you still need the answer, but am answering it in case you do.


    I also do not know if you have the 5.0L or 5.8L Engine or what options (AC/No AC, etc.).

    Click on the following free, direct Link. It has the Serpentine/Drive Belt Diagrams for the 1989 Mercury Grand Marquis for both the 5.0L and 5.8L Engines and engine options (AC/No AC, etc.).

    http://www.2carpros.com/car_repair_information/year/1989/make/mercury/model/grand_marquis/1989_mercury_grand_marquis_drive_belt_routing_diagram.htm

    "HOW TO":
    Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
    1. Find the Tensioner.
    2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    3. Remove the loosened belt off one of the other more easily accessed Pulleys.
    4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

    Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
    Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!


    Oct 24, 2009 | 1992 Mercury Grand Marquis

    1 Answer

    Need to know how to put in a surpentied belt for a Plymouth voyager


    For the 1993 Plymouth Voyager Serpentine Belt:
    Did not specify what Size Engine: 2.5L, 3.0L or 3.3L.

    Click on the following free direct Link. It has several of the Serpentine Belt Diagrams and Tensioners that are possible with your Size Engine (2.5L, 3.0L, 3.3L) and engine options (AC/No AC, etc.).
    http://www.2carpros.com/car_repair_information/year/1993/make/plymouth/model/voyager/1993_plymouth_voyager_drive_belt_routing_diagram.htm

    "HOW TO":
    Standard Rules to Removal the Serpentine Belt with a Tensioner:
    1. Find the Tensioner(s). (See Diagrams on Link)
    2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    3. Remove the loosened belt off one of the other more easily accessed Pulleys.
    4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.


    Standard Rules for Installing the Serpentine Belt with Tensioners:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

    Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

    Sep 24, 2009 | 1993 Plymouth Voyager

    1 Answer

    How to put on the serpentine belt for a 1994 plymouth grand


    Well, first of all you don't "loosen" the tensioner. Tighten that back up. Route the belt as it should go. Put a 15mm open-end or box end wrench on tensioner bolt (in the middle of tensioner.) To make this really easy, I use a "cheater" (a pipe large enough in diameter to go over wrench) to give added leverage to pull down tensioner far enough to slide belt over. Personally, I route the belt over everything except the idler pulley then pull down on the tensioner far enough to slip the belt on the idler. Because of the small cleareance, trying to use a socket on this bolt is almost impossible however, the previous is the method I've learned to be the most efficient.
    David

    Jan 04, 2009 | 1994 Plymouth Grand Voyager

    Not finding what you are looking for?
    Cars & Trucks Logo

    181 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Plymouth Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Plymouth Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...