Question about 1992 Jeep Wrangler

1 Answer

1992 jeep yj transfercase swap

Hi guys, I just removed and replaced my np231 this weekend. When my old one went out I was able to get it into 4 low and limp it home. Now with the "new" one in and everything put back together the vehicle wont move. It acts like I'm in neutral. I get absolutly nothing in 2wd all the way to 4 low. I can hear the clutch engaging but to my demise i dont move. Please HELP!!..

Posted by on

  • jerry.court Feb 09, 2009

    Yes, all full of fluids.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

Did you put transmission fluid back in the trans?

Posted on Feb 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace valve lifters in a 1992 jeep wrangler 2.5L


its in the fsm book and at alldata.com
click 93 YJ here.

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

then click engine.

posted 100s of times, ever search?, nah,.

Mar 04, 2015 | 1992 Jeep Wrangler

1 Answer

Shift patterrn


5 speed 1st top left 2nd bottom left 3rd top middle 4th bottom middle 5th top right reverse bottom right
4wd 2wd top 4high one click down neutral shift to right then push down 4low bottom lowest point

Mar 26, 2014 | 1992 Jeep Wrangler

1 Answer

Jeep yj not engage 4wd 4x4


check vaccume on top transfercase

Sep 25, 2013 | Jeep Wrangler Cars & Trucks

2 Answers

Speedo 95 yj conversion 350 with 350 turbo trans and np231 transfer case 3.73 gears 33" tires wires cut off at transfer case and there is no speedo cable what do i need to get my speedo working


The vehicle speed sensor is located in the transfer case housing. To get your speedometer working you will have to connect the wires back to the speed sensor.

Nov 02, 2011 | 1990 Jeep Wrangler

1 Answer

How to remove/install a 4 cylinder jeep Yj


If you need to ask, you have never done one. I suggest that you get a chiltons or haynes manual to guide you through it. tips are: use large bolts without heads to guide the transmission back onto bellhousing so you don't need to hang the unit on the clutch disc and risk bending it. Change the pilot bearing in the back of the crankshaft if it's the least bit worn, be very careful not to damage the crank sensor on the bellhousing, and use a good pilot shaft when aligning the disc inside the clutch cover. spread some white lube on the input shaft and front guide collar on the transmission and make sure the throwout bearing has sufficient grease in the inside groove.
good luck!!!

Sep 29, 2009 | 1992 Jeep Wrangler

2 Answers

4 wheel drive doesnt work.


Has this Jeep been modified at all?
It sounds like the shifter cable was reinstalled backwards.
Specifically the 4-Low "Not Climbing Well". 4-Low should give you the best torque and hill climbing ability.
Do you feel any "Binding" in the steering wheel (difficult to turn)?
Remember a Jeep uses real driveshafts and differentials to give you 4WD - you cannot engage 4WD or 4-Low on dry hard surfaces. It needs a little bit of slip between the wheels for turns.
Check you're fluids too.

Jul 11, 2009 | 1992 Jeep Wrangler

2 Answers

1992 4 cylinder Jeep YJ sputters while driving. Have changed cap, ingition rotor, wires.


try this site for resolve oil and resolve petrol system addertive for old cars. amitech . its good i typed into computer sludge in petrol tank but they have lots of products that might help before you do anything as these products clean the engine

Mar 26, 2009 | 1992 Jeep Wrangler

1 Answer

1987 Jeep YJ [Wrangler] so owner ship says''


Our Jeep Wrangler YJ's are equipped with a vacuum module on the front axle. It is used to engage the front axle when the transfercase is shifted into 4WD. Check the vacuum lines on the front axle to make sure they are connected. The passenger side axle shaft has a disconnect sleeve that is moved left and right by the vacuum.

Mar 01, 2009 | 1987 Jeep Wrangler

3 Answers

4 wheel drive problem on Jeep YJ


you can also check the 4 wheel drive vacuum switch on top of the transfer case...got mine for 10 bucks from parts store...fixed the problem

Dec 21, 2008 | 1992 Jeep Wrangler

Not finding what you are looking for?
1992 Jeep Wrangler Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...