Question about 2005 Ford F-150

1 Answer

Headlamps work on low beam, not on high. Indicator light not on.

Headlamps will not work on high beam. The indicator light doesn't turn on.

Posted by on

  • 1 more comment 
  • tjgill Feb 09, 2009

    Thanks, any idea of cost?

  • Anonymous Apr 04, 2009

    i have a 97 ranger, the high/low beams work and can be switched as normal. only on my instrument panel the indicator light will not come on.

  • Anonymous Mar 30, 2014

    Low beams

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 78,289 Answers

U are going to have to replace the dimmer switch/combination switch.

Posted on Feb 09, 2009

  • yadayada
    yadayada Feb 09, 2009

    Here is the price from rockauto.com, they are the lowest on the internet.

    MOTORCRAFT Part # SW6377 {#6L3Z13K359AA}
    production date of 11/29/04 $44.79



    After 11/29/04 MOTORCRAFT Part # SW5580 $93.79

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chev sub head lights wont turn on


Do you know anything about automotive electronics ? Electronic control modules .
Headlamp ON/OFF control is determined by the body control module (BCM) by a signal on the headlamp switch on input circuit when the headlamp switch is in the HEAD position. When the headlamp switch is in the AUTO position, the BCM determines headlamps ON/OFF by the voltage from the ambient light sensor.
If the headlight switch is left in the ON position, the inadvertent power control feature will turn OFF the headlights approximately 10 minutes after the ignition switch is turned to the OFF position. If the driver places the headlight switch in the ON position after the ignition switch has been turned OFF, or if the ignition switch is in the ACCY position, the headlights will remain ON until turned OFF or the battery runs dead.
The high beam indicator is illuminated when the instrument cluster receives a GMLAN serial data message from the BCM that the high beams are illuminated.
High Beams
The high beam headlamps receive voltage from the headlamp high relay located in the underhood fuse block. The BCM controls the relay on the headlamp high beam relay control circuit. High beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is grounded, the BCM grounds the headlamp high beam relay control circuit, illuminating the high beam headlamps. The right and left high beam circuits are independent and are fused independently in the underhood fuse block.
Low Beams - Standard
The low beam headlamps receive voltage from the headlamp low beam relay located in the underhood fuse block. The BCM controls the relay on the headlamp low beam relay control circuit. Low beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is open, the BCM grounds the headlamp low beam relay control circuit, illuminating the low beam headlamps. The right and left low beam circuits are independent are fused independently in the underhood fuse block.

Hooking up a factory scan tool an checking DTC'S - diagnostic trouble codes would be the very first step in trouble shooting this problem .
DTC B257A 00: Headlamp Switch Input Signal Mismatch
DTC 2575 00: Headlamp Control Circuit

Jun 30, 2017 | Cars & Trucks

1 Answer

Hi my name is Larry I have a 1998 Pontiac sunfire & my problem that I have is I have low beam. But no high beam.


It's probably the switch , but testing to know for sure is alwasy a good idea .

Headlamps Inoperative - High Beams
Step
Action
Value(s)
Yes
No
1
Did you perform the Daytime Running Lamps (DRL) System Check?
--
YES - Go to Step 2
NO - Go to Daytime Running Lights (DRL) System Check
2
Disconnect the turn/hazard headlamp switch connector C1.
Connect a fused jumper between terminal B of the turn/hazard headlamp switch assembly harness connector C1 and ground.
Do the high beam headlamps operate?
--
YES - Go to Step 3
NO - Go to Step 4
3
Replace the turn/hazard headlamp switch assembly.
Did you complete the repair?
--
Go to Daytime Running Lights (DRL) System Check
--
4
Repair the open in CKT 1200 between the turn/hazard headlamp switch assembly. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?

Daytime Running Lights (DRL) System Check
Step
Action
Normal Result(s)
Abnormal Result(s)*
1
Turn the headlamp switch to the HEAD position.
Turn the headlamp dimmer switch to the LOW position.
The low beam headlamps are ON.
The high beam headlamps are OFF.
Headlamps Inoperative - Low Beams
2
Turn the headlamp switch to the HIGH position.
The high beam headlamps are ON.
The high beam indicator is ON.
The low beam headlamps are OFF.
Headlamps Inoperative - High Beams
3
Turn the headlamp switch OFF.
Turn the ignition to ON.
Disengage the parking brake.
The high beam headlamps come ON at a reduced intensity in approximately 30 seconds.
Daytime Running Lamps (DRL) Inoperative, Headlamp Switch Operates Normally
* Refer to the appropriate symptom diagnostic table for the applicable abnormal result.

Jan 13, 2017 | 1998 Pontiac Sunfire

1 Answer

No low beam. Good high beam. No day lights. What's wrong?


No on the fuse . The LH HDLP and RH HDLP fuse in the fuse block - under hood, supply battery positive voltage to both low and high beam lamps at all times. For manual operation, when the headlamp switch is in the ON position, the headlamp switch supplies ground directly to the headlamps and to the body control module (BCM) on the headlamp low or high beam signal circuit, depending on the position of the headlamp dimmer switch. The BCM uses this signal to determine if the conditions are present to illuminate the daytime running lamps or park lamps.
The headlamps may be turned on 2 different ways. First, when the driver places the headlamp switch in the ON position, for manual operation. Second, with the headlamp switch placed in the OFF position activating automatic lamp control (ALC).For ALC operation, the BCM receives a signal from the ambient light sensor indicating a low or high ambient, outside, light level. Under low light conditions the BCM grounds the headlamp relay control circuit energizing the headlamp control relay. The now closed relay supplies ground through the headlamp switch to the headlamps and the BCM on the headlamp low or high beam signal circuit, depending on the position of the headlamp dimmer switch. When the BCM grounds the headlamp relay control circuit it also grounds the park lamp relay control circuit illuminating the park lamps. The headlamp relay is grounded at G203.
Daytime Running Lamps (DRL)
The low beam headlamps operate at reduced intensity when in daytime running lamps (DRL) mode. The ground circuit to the switch side of the DRL relay has a resistor in-line to reduce the intensity of the low beam headlamps for DRL operation. The body control module (BCM) receives a signal from the ambient light sensor indicating a low or high ambient, outside, light level. Under daylight conditions the BCM grounds the DRL relay control circuit energizing the DRL control relay. The now closed relay supplies ground directly to the low beam headlamps and to the BCM on the headlamp low beam signal circuit. The low beam headlamps now illuminate with reduced intensity. The DRL relay is grounded at G203. Any time the headlamps are illuminated the DRL will not illuminate. Manual park lamps do not effect DRL operation.

Feb 23, 2016 | 2005 Chevrolet Equinox LS

1 Answer

Why don't lights work?


Both the headlight switch and the BCM provide a ground, or control circuit, to the headlight relay coil circuit for manual or automatic headlamp operation. When you place the headlamp switch in the OFF position, and the ambient light sensor indicates low light conditions, the BCM energizes the headlamp relay for low beam operation. You may switch the headlights to high beam by pulling the dimmer switch handle toward you until the dimmer switch is activated. When the dimmer switch is placed in the HIGH position, the indicator lamp input to the BCM is pulled low. The BCM then sends a class 2 message to the instrument cluster in order to illuminate the high beam indicator lamp.
Low and High Beams Headlamps Inoperative ?
Replace the headlamp switch. Refer to Headlamp Switch Replacement .
Did you check the headlamp relay ? Location ,left instrument panel
Did

Nov 11, 2015 | 2001 Chevrolet Monte Carlo

1 Answer

Why are Dashboard lights not working on high beam?


check the dimmer switch, I had the same problem. this dimmer switch didn`t dim on low beem but went out on high beams, turned the dimmer switch up and down/on and off and it came back on.

Apr 24, 2014 | 2008 Toyota RAV4

1 Answer

Oldsmobile intrigue problems


The switch is bad >
Each headlamp is individually fused so that battery voltage is applied to the individual lamps at all times through circuit 1640 for the LH headlamps and through circuit 1740 for the RH headlamps. When the headlamp switch is in HEAD, the ground is applied directly to headlamp switch through circuit 1750. When the headlamp switch is placed in LOW, ground is applied to the low beam headlamps through circuit 1201. When the headlamp switch is placed in HIGH, ground is applied to the high beam lamps and to the high beam indicator through circuit 1200. The high beam indicator is fused so that battery voltage is applied at all times through circuit 640.

The box you hear the click in is the daytime running lights control module .
Do you know how to do electrical testing using a DVOM- digital volt ohm meter or a test light ?

Low and High Beams Headlamps Inoperative
Step
Action
Value(s)
Yes
No
1
Was the headlight system check performed?
--
YES - Go to Step 2
NO - Go to Headlight System Check
2
Does flash to pass function normally in the headlight system check?
--
YES - Go to Step 3
NO - Go to Step 7
3
Does the autolamps low and high beam operate normally?
--
YES - Go to Step 4
NO - Go to Step 6
4
Turn the headlamp switch to the Head position and the headlamp dimmer switch to Low position.
Using a test lamp, backprobe between connector C201 terminal W and ground.
Is the test lamp on?
--
YES - Go to Step 5
NO - Go to Step 6
5
Repair poor connection or open in circuit 1750 between connector C201 terminal W and S283.
Is the repair complete?
--
Go to Headlight System Check
--
6
Replace the headlamp switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle for service procedure.
Is the repair complete?
--
Go to Headlight System Check
7
Repair poor connection or open in circuit 1750 between S283 and ground.
Is the repair complete?
--
Go to Headlight System Check

May 13, 2017 | Cars & Trucks

1 Answer

My 2002 impala headlights don't work at night or in dark places like a tunnel or under a bridge, they only work in the day time. I have day time runner lights and they automatically turn on when I start my...


You can't turn them on manually with the switch . You have the switch set on auto ?
Headlamps
You can use the headlamps in two different ways.
• Place the headlamp switch in the ON position for normal operation.
• Place the headlamp switch in the OFF position for automatic lamp control (ALC). During ALC the high beam headlamps are On at reduced intensity for daytime running lamp (DRL) operation in daylight conditions, or low beam headlamps On in low light conditions.
The DRL/EXT LTS fuse and the EXT lamps fuse in the underhood junction block supply battery positive voltage at all times to both of low beam lamps and to the right high beam lamp. The low beam circuit continues to the high/low beam switch, then, depending on the position of the dimmer switch, connects to the normally-open headlamp relay switch contacts. Placing the headlamp switch in the HEAD position provides a ground path for the headlamp switch input of the Body Control Module (BCM). After receiving this input, the BCM energizes the headlamp relay. When the headlamp relay is energized, the low beam circuit is connected to ground G201. The high beam circuit is divided into a left and a right side circuit.
The DRL/EXT LTS fuse in the underhood ignition block supplies battery positive voltage to both the coil and to the normally-closed contact of the DRL relay switch circuit. During high beam operation, the left side current flow is through the closed contacts of the DRL relay, and to the left high beam lamp.
The EXT Lamps fuse in the top of the engine fuse block supplies battery positive voltage to the right high beam lamp. Both high beam circuits are then connected together, and continue to the dimmer switch. When the driver closes the high beam contacts of the dimmer switch, the circuit is grounded at G201.
Both the headlight switch and the BCM provide a ground, or control circuit, to the headlight relay coil circuit for manual or automatic headlamp operation. When you place the headlamp switch in the OFF position, and the ambient light sensor indicates low light conditions, the BCM energizes the headlamp relay for low beam operation. You may switch the headlights to high beam by pulling the dimmer switch handle toward you until the dimmer switch is activated. When the dimmer switch is placed in the HIGH position, the indicator lamp input to the BCM is pulled low. The BCM then sends a class 2 message to the instrument cluster in order to illuminate the high beam indicator lamp.
If the headlamp switch is left in the head position, the inadvertent power control feature will turn off the headlights 10 minutes after you turn the ignition switch to the OFF position. If you place the headlamp switch in the head position after the ignition switch has been turned OFF, or if the ignition switch is in the ACCY position, the headlights will remain ON until you turn them OFF or until the battery runs dead.

Dec 07, 2017 | Chevrolet Impala Cars & Trucks

1 Answer

1994 ford f-150 with day time running lights headlightnot working


Daytime Running Lamps
The daytime running lamp (DRL) system is designed to turn the high beam headlamps on, with a reduced light output, and without illuminating the high beam indicator lamp in the instrument panel. You have a DRL Module.
The multifunction switch is the stalk on your column.

This is 96 F150 circuit. Don't have 94.

51f651c.gif
Symptom Chart, Headlamps HEADLAMPS Condition Possible Source Action
  • Headlamps Inoperative
  • Circuitry open/shorted.
  • Damaged headlamp switch.
  • Blown fuse.
  • GO to Pinpoint Test A .
  • Headlamps On Continuously
  • Circuitry open/shorted.
  • Damaged headlamp switch.
  • GO to Pinpoint Test B .
  • High Beams or Low Beams Inoperative
  • Circuitry open/shorted.
  • Damaged multi-function switch.
  • GO to Pinpoint Test C .
  • One High Beam or One Low Beam Headlamp Inoperative
  • Circuitry open/shorted.
  • Damaged connector.
  • Headlamp bulb damaged.
  • GO to Pinpoint Test D .
  • Flash-to-Pass Inoperative
  • Blown fuse.
  • Circuitry open/shorted.
  • Damaged multi-function switch.
  • GO to Pinpoint Test E .



73d6d64.gif

Feb 25, 2009 | 1994 Ford F150 Styleside Supercab

1 Answer

Where is the module for the day time running lights on a dodge ram B 1500? 1996


Notes CIRCUIT OPERATION - CANADA
On Canadian vehicles, the low-beam headlamps operate when the ignition switch is in the RUN position and the headlamp switch is OFF.

When the ignition switch is in the START or RUN position, circuit A1 from fuse 15 in the Power Distribution Center (PDC) connects to circuit A21. Circuit A21 powers circuit F18 through fuse 19 in the fuse block. Circuit F18 feeds the Daytime Running Module (DRL) module.

Circuit L20 from the headlamp switch connects to DRL module. Circuit L20 is HOT at all times.

The DRL module receives the vehicle speed sensor input from circuit G7. Circuit G34 from the DRL module provides power for the high beam indicator lamp in the instrument cluster.

Circuit L4 powers the low beams of the headlamps. When the headlamp switch is OFF, the DRL module powers the low beams on circuit L4. When the headlamps are ON, the multi-function switch powers the low beams on circuit L4.

Circuit L3 feeds the high beams of the headlamps. When the operator flashes the headlamps with the stalk of the multi-function switch, the DRL module senses voltage on circuit L3. When it senses voltage on circuit L3, the DRL module stops supplying power to the low beams on circuit L4.

Circuit Z1 provides ground for the DRL module.

Aug 19, 2008 | Dodge Ram 1500 Cars & Trucks

Not finding what you are looking for?
2005 Ford F-150 Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

78289 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5655 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...