Question about 2002 Land Rover Freelander

1 Answer

1998 freelander it is a hydraulic clutch the peddel gos to the all the way dose not come back and you here air through hose but i would like to know were the hydraulic clutch is on the engine its self so i can see if it is the hose ok please and thank you i have never worked on land rovers before and the owners manial dosent tell me either

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 104 Answers

First Top up the fluid for the hydraulic clutch. This reservoir should be on the fire wall beside the brake master cylinder.

The Clutch slave cylinder is located on the side of the bell housing under the car. You can follow the hose or line from the mater cylinder to find it. There is a bleeder on the end of this cylinder. Open the bleeder at least a few turns and have someone watch the fluid in the master cylinder and just let the fluid run out until you get no air. If it will not self bleed as described above, have someone pump the clutch pedal to the floor and hold it there. Open the bleeder at the slave Cylinder until no more fluid or air comes out and close the bleeder. Tell the person holding the clutch down to slowly release the pedal, or pull it up from the floor. again, slowly. Repeat this process until you have no more air being expelled. Do not let the fluid level of the master cylinder drop below minimum. Note Brake fluid used in this hydraulic system will remove paint. Be careful.

Good Luck

Posted on Feb 09, 2009

  • bigtripod Jun 10, 2011

    i am so gratefull for your solution "no messing sround or complicating things just strait to the point thank you tripod (billy manson jersey channel islands uk!)

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The Clutch disc and Release Bearing for the TD4-Freelander, were replaced recently. The Pressure Plate was still in a good condition.Gears difficult to engage.Please advise.Tks.John.


Most likely still has air in hydraulic clutch slave system. Many transmisions will have dificulty shifting if clutch doesn't full disengage. If air is in system it won't allow full disengage thus difficulty in shifting even possible grinding gears

Sep 17, 2016 | 2002 Land Rover Freelander

1 Answer

My 1998 pajero 5 speed got no gears at all dose anyone know wat it could bee


If you mean you can't get it into gear, that means either
* the clutch hydraulic system has a problem, commonly the slave cylinder; or
* the clutch itself has worn out.

Mar 01, 2015 | Mitsubishi Pajero Cars & Trucks

1 Answer

Where is the transmission cable located on 1998 corolla


Clutch cable? Actually, I think you'd have a hydraulic clutch. If it's cable, it would come out of the firewall, where your clutch pedal operates, and down to the transmission. If it's hydraulic, there'd be a clutch reservoir just beside your brake reservoir on the firewall, with a hose leading down to a "clutch slave cylinder" mounted on your transmission. If you have no clutch, this slave cylinder can be easily bled of air and will gravity feed new fluid to the cylinder.

Oct 25, 2011 | 1998 Toyota Corolla

1 Answer

Clutch slave cylinder how to bleed


HYDRAULIC SYSTEM BLEEDING Do not use fluid which has been bled from a system to fill the reservoir as it may be aerated, have too much moisture content or possibly be contaminated. Clean the dirt and grease from the cap to ensure that no foreign substances enter the system. It is also important to maintain the fluid level in the clutch reservoir to the top step with hydraulic clutch fluid Hydraulic Clutch Fluid GM P/N 12345347 or equivalent.
  1. Attach a hose to the bleeder screw on the clutch actuator assembly and submerge the other end of the hose in a container of hydraulic clutch fluid.
  2. Depress the clutch pedal slowly and hold.
  3. Loosen the bleeder screw to purge air.
  4. Tighten the bleeder screw to 18 inch lbs. (2 Nm).
  5. Let up on the clutch pedal.
  6. Repeat Steps 2 through 5 until all air is purged from the system.
  7. Fill the reservoir to the top step with hydraulic clutch fluid.
  8. Repeat this bleeding procedure if there is a grinding noise during the clutch spin down procedure.
prev.gif next.gif

Oct 13, 2010 | 1998 Chevrolet Cavalier

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

2 Answers

The cluch pedal does not come back up at times and the following time it does not work and consequently cannot swith to a gear on my Landrover Freelander 2003, 2L. diesel. Gilbert


i would change the clutch and while you are at it i would also change the clutch arm and bush as they are prone to seizing causing a stiff clutch action and dropped peddle and slave cylinder failure , slave is plastic and the ears and white coller snap off, when cold if your car feels like its jerking as you move off i would deffently say it is the clutch arm and not the clutch, but as you will need to remove gear box any way i would renew the clutch and thrust bearing.

Feb 13, 2010 | 2002 Land Rover Freelander

2 Answers

How do I bleed the master clutch cylinder


It will take two people, one to push clutch peddel, and one to open bleeder, same as bleeding breaks, the person pushing peddel pumps peddel a few times and the last time holds to floor, other person opens bleeder to let air out, and then closes bleeder while peedel is still depressed, do this process over and over untill you get clutch or a steady stream of fluid with no air , while keeping an eye on fluid level in resavor.

Apr 05, 2009 | 1996 Nissan Maxima

2 Answers

1998 S-10 Manual Tranny problems


yes it sure sound like you have an air bubble in the slave cyl.
you must have seen my oil can bleeder
ive also made a new one out of a garden sprayer and adapted down to fit the bleeder screw.66253ce.jpgand this is even faster and makes bleeding simple good luck

Nov 13, 2008 | 1998 Chevrolet S-10 Pickup

Not finding what you are looking for?
2002 Land Rover Freelander Logo

420 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

63990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...