Question about 1995 Jeep Grand Cherokee

1 Answer

How to clear the diagnostic codes on my 1993 jeep cherokee?

How to clear codes on 1993 jeep cherokee

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

To clear codes on these, you can disconnect the battery, then re-connect. The only code remaining will be one indicating battery power was interuppted. This will not work on 98 and newer vehicles.

Posted on Feb 08, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I am getting diagnostic code 22

Error Code: 22
Description: Engine Coolant Temperature circuit malfunction.
Possible Causes:
- Wiring.
- Coolant Temperature sensor defective.
- ECM.

Apr 25, 2014 | 1993 Jeep Grand Cherokee

1 Answer

I have a 93 Jeep Cherokee with a 4.0. I installed a new coil and it refuses to spark. cleaned cap, rotor and plugs. Tested plug wires all good. 12v going to coil. Still no spark. Can the magnet in the...

Take it to the dealer and have it checked on diagnostics as this will bring up an error code telling you what the problem is, it could be that when you changed your bits and pieces you may have triggered an error code on the computer and you will have to have it cleared to put things right,or it could be that the cps has triggered an error code and you will need to clear it to get the car running again i had the same problem with my cherokee and i changed the cps but it still would not start and it was only by chance that i found out from a friend who works on them that i found out about the computer error, but because i live in the sticks of egypt there was no where to get it done so my friend told me how to bypass the error code on the computer and it has been fine ever since hope this helps

Feb 27, 2013 | 1993 Jeep Cherokee Country

1 Answer

Were is the DTC connector located on the Grand Chero?

On 1993 Jeep Grand Cherokee 4WD 5.2L MFI 8cyl the OBD Diagnostic Link Connector is located under hood, passenger side, front engine area, corner, mounted on fenderwell.

Hope this helps (remember to rate and comment this answer).

Sep 14, 2011 | 1993 Jeep Grand Cherokee

1 Answer

2000 jeep cherokee stopped running while driveing changed coil plugs and fuel pump and crank sensor still not running

Have you checked for DTC's (diagnostic trouble codes) in the PCM (powertrain control module)? If so, what were they. Comment back.

Aug 18, 2011 | 1993 Jeep Grand Cherokee

1 Answer

I have a P0702 transmision trouble

Transmission Control System Electrical=P0702 code,
Have you talked to a jeep dealer yet,
Ask if there are any TSB's on this problem.
Technical Service Bulletins from Jeep when they find and solve different complaints.
What ever is doing this is a soft code,A soft code is one that will clear it's self with the cycle of the key to off then on and code goes away,But have them check history codes to see if it is sounds like it is going into limp mode,this feature is when the computer sees a transmission falt it wont up shift,so you don't harm the tranny,but will let you limp to a shop to get repaired.have you ever noticed the speedometer going to 0 then this happens?
that would be the output sensor.

Nov 15, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Need to know what trouble code 55 is on the 1993 jeep cherokee country 4.0 l

code 55 is the "end" code showing that the diagnostics have been completed. If you had no other codes, then there is nothing stored as a fault in the computer.

Oct 21, 2009 | 1993 Jeep Cherokee Country

1 Answer

I have a 2005 Jeep Cherokee Laredo. Diagnostic

Implausible Fuel Volume Signal Received

This usually points to a bad PCM (powertrain control module).

Sep 14, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Resetting check engine light for 2003 Toyota Sienna

Take it to Auto Zone. They will check the codes for free, and clear them too.

Apr 04, 2009 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

Related Topics:

484 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides