Question about 2003 Hyundai Accent

1 Answer

E Brake light is on

No other symptons visable

Posted by on

  • silver top May 11, 2010

    hi from whatyou say no other symptoms ? assume fluid level ok? park brake switch operating ok? brake pads plenty of pad left? ie not too low to activate warning light does brake pedal feel ok ?



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 98 Answers

Based on the very limited amount of information given, in general when the brake light comes on it could be for a variety of reasons but it is always best to start simple. Open the hood and somewhere towards the back you should see a plastic container that houses the brake fluid. It should have a warning on top about using only DOT approved brake fluid or some similar warning. Check the level as indicated on the outside of the brake fluid tank. If it is low add to the proper level. The fluid level will be low because you either have (A) a leak or (B) your brakes are going to need to be changed soon. Adding fluid (should) make the light go off but you should have the brakes inspected ASAP and most places do it for free.

Posted on Feb 15, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Brake lights on

This is a serious fault and needs sorting fast!!!!!! Check front and rear brake area`s for sign`s of leakage,check brake hoses,pipes and fittings for sign`s of leakage if there are no visable sign`s it maybe the master cylinder..PLEASE don`t delay do it today!!!!!!!!

Dec 30, 2012 | Cars & Trucks

1 Answer

No brake lights 2003 Ford Explorer but high mount works

maybe the one of the contacts on the bulb broke or the brake fuse

Aug 06, 2012 | 2003 Ford Explorer

1 Answer

83 regal heard a pop then brake light came on pedal goes all the way no brakes

If there are no visible leaks check your master cylinders behind the tires might be why there's no brake pressure or are we talkin about the emergency brake pedal?

Mar 28, 2012 | 1983 Buick Regal

1 Answer

I have a 1990 chevy 1500 when I drive the left rear wheel engage. And when it does that I have to press the brake pedal to disengage. I change wheel cyclinders,brake lines and all, but it still do the same...

check the rear brake adjustment and clean out all the brake dust.this can happen if the brakes are not adjusted properly as the misadjusted side will pull the brake shoes into the drum and act like the brake is on.if it was an abs problem or sympton the abs light should have come on to indicate a problem depending at what speed it happens.

Feb 09, 2012 | 1990 Chevrolet K1500

1 Answer

How do I replace a brake light in a land rover freelander 2004 - does the glass cover screw off internally or externally. Are the brake light and tail light bulbs combined? Many Thanks David

If there are visable screws around the tail lite lens yes they come out and just screw off the bulbs socket than the bulb,,,If no visable screws than the should be a panel on in side of vehcle back side that comes out for access to the lights.

Mar 11, 2011 | Land Rover Freelander Cars & Trucks

1 Answer

Toyota carina injection 1993 2000cc auto cuts out as soon as I

Does the vehicle restart and die when you put it in gear. If answer is yes then you need a torque converter clutch solenoid (TCC) or a brake light switch. The brake light switch cancels the TCC at a slow down or stop.. If it doesn't cancel it you will stall out. If your vehicle restarts and dies once you put it in gear then its the TCC. If none of these symptons fit your vehicle get back to me .

Apr 18, 2010 | 1991 Toyota Camry

1 Answer

I\ the brake lights are on the bumper only i would

Yes just splice the wires you may need to guy wire like 18 gauge auto wiring from an auto parts store and the **** connectors and wire crimmpers really easy job to do. Or have a mechanic do it some of them know how to wire stuff up they might charge you around $50 bucks.

Good Luck!

Feb 08, 2010 | 2002 Land Rover Freelander

2 Answers

Just found out i have no tail lights both sides of nissan navara 2008 outlaw model. could be a quick fix, just putting the question out there!

First off; check the tailamp fuse.location of fuse box is in owners manual.Fuse identity/s are on box cover as is little yellow pulle prong See if breaker wire(visable thru fuse) is seperated and if so,replace fuse sometimes a spare is in the box lid.Done

Nov 10, 2009 | Nissan King Cab Cars & Trucks

1 Answer

No front, or rear running lights, or dash lights

check tailight and instr light fuse with a test light rather than visably

Mar 26, 2009 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Emmission system light

take it to autozone and they will plug in their OBD11 computer and tell you exactly what it means... or take it to any mechanic who has one, my light comes on if i get crappy cheap gas

Mar 21, 2009 | 1999 Volvo S80

Not finding what you are looking for?
2003 Hyundai Accent Logo

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides