Question about 2004 Saab 9-3

3 Answers

Saab 93 window not closing fully

The saftey feature cuts in on the drivers window and it closes then opens automatically. stripped the door nothing loose or broken.

Posted by on

  • 1 more comment 
  • lwallace22 Feb 10, 2009

    solution 2 did shut the window but no beep to indicate any reset. problem still exists on on normal operation. thanks anyway

  • butterdj Mar 24, 2009

    You have to disconnect your battery for 30 seconds. I tried both of these and neither worked.

  • Anonymous Mar 27, 2014

    I hit my automatic door lock and my sunroof and two front windows automatically opened synchronized , now my sunroof won't close all the way??

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

1. put key to ON, hold window button down until all the way down, then do same for up, repeat one more time until you hear BEEP. You just calibrated your window. You will need to do this everytime you disconnect your battery.
or...
2. anytime window has power and has automatically gone down, hold the X (window lock button) down while holding up on your window button, again untill you hear BEEP. not sure what this does, but it fixed the problem for me.

Posted on Feb 10, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

As mentioned here, this worked for me on a 55 reg:

Disconnect the battery for 30 seconds. Then follow the calibrate instructions that can be found under "Windows" in the owner's manual. Took less than 5 minutes in all to fix.

Posted on Jun 01, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I disconnected the battery and left for 30 seconds, when I reconnected the window restored it's normal settings..

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does the power window button blink on and off and the automatic feature doesn't work in the 2008 Toyota Sienna?


NOTE:
Anytime the batteryterminal has been disconnected, please initialize the driver's door power windowand front passenger's door power windowafter reconnecting the batteryterminal.

With ignition switchin the "ON" position, do the following:

1. Push down and hold the driver's door power windowswitch to completely open the window.
2. Pull and hold up the driver's door power windowswitch until the window closes.

Continue holding the switch for approximately one second until the switch changes from blinking to a constant illumination.
3. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

At this time the power window switchfor the passenger's door windowshould be blinking.
4. Push down and hold the passenger's door power windowswitch to completely open the window.
5. Pull and hold up the passenger's door power windowswitch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
6. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

Feb 09, 2016 | Toyota Cars & Trucks

1 Answer

Reconect car battery rear door window will not go up


To reset the windows, you need to open them fully, then as quickly as you can, close them with the button until the window is fully closed again. Hold the closed button down until you hear a beep and get a Window Set message. You may need to do this several times until the window resets. Then open and close the window several times for the automatic open/close feature to function if it is available on your evhicle. Hope this helps.

Dec 05, 2013 | 2004 Land Rover FreeLander

1 Answer

My saab 93 on a 56 plate and the drivers window has stopped working. It is in the closed position thank god. And ideas? Many Thanks Andy


Hi, Andy. Did you check the fuses because I think you have blown fuse.Don.t know were the fuses are? Because your car is first registered second half 2006 RHD just open the driver.s door and look on dashboard RHside.There is plastic cover.Open it.Check fuses useing test lamp,not visual.

Apr 27, 2010 | 2008 Saab 9-3

2 Answers

Malfuntioning driver's side power window upon opening door lever.


get it to the dealer asap.

you definitely need to take apart the door. There's something not right inside.

May 24, 2009 | 2002 Porsche 911

1 Answer

The drivers side door on my 93 mustang is not fitting right making it hard to close and open the door. I have to lift it to open or close


check the door hinge pins and make sure they are fully seated. Also check the hinge pin bushings - they are made of bronze and if they wear out, the door will droop

Apr 20, 2009 | 1993 Ford Mustang

3 Answers

Driver's Side Window Won't Stay Up


As mentioned here, this worked for me on a 55 reg:

Disconnect the battery for 30 seconds. Then follow the calibrate instructions that can be found under "Windows" in the owner's manual. Took less than 5 minutes in all to fix.

Mar 26, 2009 | 2003 Saab 9-3

1 Answer

Creaky car door


I believe you will need to replace the part that limits the opening of the door. It is found between the 2 hinges.

Mar 14, 2009 | 1995 Saab 900

2 Answers

2003 vector drivers side power window won't stay up


Your pinch protection is not correctly set. You can defeat the pinch protection by holding down the window lock button when you close the window. However, to "solve" the problem, you need to reset the pinch protection. My dealer charged me $100 to reset the pinch protection on my 2003 9-3 Arc.

Mar 09, 2009 | 2003 Saab 9-3

1 Answer

Saab 93 2001 interior light not working when I open the door


Your little plunger switch connection just below the door hinge is corroded or defective on that door. The switch is not on the door itself but on the frame where the body meets the door when closed. You can push in the switch with your finger to test it. 

Dec 19, 2008 | 2001 Saab 9-3

Not finding what you are looking for?
2004 Saab 9-3 Logo

Related Topics:

4,064 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

yadayada
yadayada

Level 3 Expert

63242 Answers

rgbypoet

Level 2 Expert

162 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...