Question about 2004 Chrysler PT Cruiser

1 Answer

2004 chrysler pt cruiser starter motor removal

How do you remove the starter motor on a 2004 pt cruiser? It's the non turbo engine. I need to remove the starter motor so I can get to the crankshaft sensor. Thanks!

Posted by on

  • 5 more comments 
  • daymon_grand Feb 08, 2009

    Appreciate the advice but getting to the starter is not that easy.

  • Anonymous Mar 14, 2014

    how to replace timing belt on 2004 pt cruiser

  • Anonymous Mar 20, 2014

    I just installed an aftermarket cd player into a 2004 PT Cruiser. All of the speakers work except for the tweeters. All that I am getting through them is static. I purchased the wiring harness for the PT Cruiser, but still only have static in the tweeters.

  • Anonymous Mar 20, 2014

    my pt 2004 cruiser is leaking alot of oil when i turn my car on.

  • Anonymous Mar 22, 2014

    what type of oil do i use for my 2004 pt cruiser

  • Anonymous Mar 23, 2014

    remove and reinstall engine

  • Anonymous Mar 25, 2014

    2004 starter motor where is it located on the engine. and the solenoid where is it located?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

You may sneak it out with small fingers with out pulling out the starter.

If starter removal is required,Just unhook the battery cables,Remove the 2 bolts holding the starter on.


Please rate this a fixya

Posted on Feb 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the turbo motor and put a non turbo motor in a 2003 pt cruiser


Changing out an entire engine is no easy feat. The biggest difference you'll have is with the exhaust system. The non turbo engine connects differently.

Oct 01, 2014 | 2003 Chrysler PT Cruiser

1 Answer

Pt Cruiser 2004 Turbo How to determine if starters bad?


pull the starter motor and have it bench tested for worn bushes ( allowing the armature to pole out) and brushes worn too far down

Jul 15, 2014 | 2004 Chrysler PT Cruiser

1 Answer

Replacing 2004 PT Cruiser Turbo battery


there is a metal bar holding the battery on my 05 pt cruiser, how doi remove it

Jan 20, 2012 | 2004 Chrysler PT Cruiser

1 Answer

Whats the position of the crankshaft position sensor on 2005 pt cruiser non turbo


P0344 CHRYSLER - Camshaft Position Sensor Intermittent Interruption Bank 1 Sensor 1
Possible causes - Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit

Dec 14, 2011 | 2005 Chrysler PT Cruiser

2 Answers

Where is crank sensor on 2005 PT Cruiser? It absolutely is not above the oil filter as on 01-03 PT's.


REMOVAL - 2.0, 2.4, 2.4L TURBO
The Crankshaft Position Sensor is in the front of the engine block just under the starter motor (CRANKSHAFT POSITION SENSOR LOCATION).

Disconnect the negative battery cable.
Raise vehicle and support.
On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
Remove the Structural Collar (Structural Collar and Bending Strut-(Automatic Transaxle Equipped) ), refer to the Engine, Structural Collar Removal and Installation section.
Unlock and disconnect the electrical connector to the crankshaft position sensor.
Remove the crankshaft position sensor bolt.
Remove the sensor. Arrow points to sensor in picture.


emissionwiz_108.gif

Aug 22, 2011 | 2005 Chrysler PT Cruiser

1 Answer

I cannot remove the rt side motor support tower...


jack the motor up from underneath a few inches then you can remove

Mar 24, 2010 | 2003 Chrysler PT Cruiser

1 Answer

How do i replace the liquid line and drier on a 2004 pt cruiser 2.4L turbo engine.


first you must recover the freon from the system then change the line always installing new orings, evacuate the system "which means to put it into a vacuum to remove all the air and moisture out of the system" then recharge and enjoy....on your turbo pt it calls for .3 for the job ...anyone should be able to do it in like 30-40 min. proved you have the right tools...recovery machine and so on.....

Sep 19, 2009 | 2004 Chrysler PT Cruiser

1 Answer

Where can I find the crankshaft position sensor on a 2005 Pt Cruiser Non turbo gasoline


IT IS LOCATED IN THE BLOCK BELOW THE STARTER..UNPLUG CONNECTOR AND 1 BOLT..IT MAY BE STUCK IN BLOCK..SPRAY WITH PENETRATING OIL..MOVE BACK AND FORTH PULL OUT OF BLOCK

Jul 14, 2009 | 2004 Chrysler PT Cruiser

1 Answer

Replacing 2004 PT Cruiser Starter


He can do it. Tell him to just be patient (everything is a tight fit in a PT) and remember to disconnect the battery first. No special tools are required. He may have to move a bracket or two for access. It lives on the left side (front) of the motor and easiest to get to from underneath.

May 21, 2009 | 2004 Chrysler PT Cruiser

Not finding what you are looking for?
2004 Chrysler PT Cruiser Logo

1,529 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...