Question about 1995 Ford Probe

1 Answer

95 probe 2.0 stalls now wont start

I have replaced the dist, ign modular, still wont start and stay running. then sounds like there is no compretion, but then it will fire again. timming is good.my code reader says code 211 P I P , "primary ignition pickup system defalt .what do i do

Posted by on

  • Jerry Koski
    Jerry Koski May 11, 2010

    first try checking all grounds like the one coming from the ignition modular .. and any other grounds .. pull on all wires that appear to be a ground and see .. just a little thought.. jerry

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

There are a couple of small relays on your fire wall that could be giving you grief. try replaceing those.

Posted on Feb 17, 2009

  • rufftuffcrea Feb 17, 2009

    there are a couple of small relays on your fire wall that could be giving you grief. try replaceing those.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

1994 mustang gt auto trans keeps stalling while


replace fuel filter and if it continues have pump pressure checked

Sep 09, 2014 | 1994 Ford Mustang

1 Answer

My '99 chevy truck with 5,7L 350 will start but wont stay running. put new fuel pump and relay switch in


First you must determine if the fuel is stopping or the spark is stopping..If the fuel is stopping this could be a computer problem.. If the spark is stopping then it could be the IGN Module in the distributer. or any nomber of sensors. Squirt a little fuel directly into the Throttle body on the intake manifold.. If the truck runs longer its probably loss of fuel.. Do this several times to make sure, be careful and only use a small amounty of fuel.. you do not want a fire.. RE: Spark: Take a plug wire and an old plug..put the wire on the plug.. hold the plug against a good ground .. have someone crank the engine .. does the plug stop firing? The engine dies.. and will not restart for a minuet or so.. during this "no start" time do the plug test. If the plug will not fire during this time take the module out and take it to Orillys Auto parts.. They can test it.. really expensive part. Don't replace until you know it is BAD..

May 14, 2014 | 1999 Chevrolet K1500

1 Answer

NO FIRE AGAIN


Make sure fuel pump is getting power. Im not sure but I think ignition is wired through fuel pump so if it dont pump fuel it wont spark either

Feb 22, 2013 | 1999 GMC Jimmy

1 Answer

Replacement of dist with paint marks removed


The codes will stay in place till cleared by a scanner. Take it to Auto Zone and they will clear the codes for you free of charge

Mar 19, 2010 | 1998 GMC Sierra

2 Answers

Will turn over but not start have replaced plugs wires dist.cap rotor ignition module


Do you have spark??? if so, check fuel pressure, these trucks must have 60 psi to run, 50 psi will not work,.

Feb 06, 2010 | 1999 GMC Sierra

2 Answers

1992 k1500, auto, air,turns over strong but wont fire


Bad sparkplugs could be your problem. You should also check your power cables and make sure the batt has the volts and amps it needs. Also take a look at ecm and other fuses. I hope the info helps and good luck.

Aug 29, 2009 | 1992 Chevrolet K1500

1 Answer

The distributor not firing


tap lightly on dist. not on cap while someone cranks motor,be careful of moving parts,if it starts change ign. module in dist. if not check cap rotor,coil and power to ign.module,if theres power to module my bet would be on ign. mod

Feb 20, 2009 | 1990 Honda Accord

1 Answer

Problem 95 probe


crank shaft sensor? I've had these be bad in a couple of vehicles, and I spent weeks/months worrying about the possible cause. Just a possible thought.

Feb 18, 2009 | 1995 Ford Probe

Not finding what you are looking for?

Open Questions:

See all 1995 Ford Probe Questions

1995 Ford Probe Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5608 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...