Question about 1993 Ford Ranger SuperCab

1 Answer

Lock cylinder problems

1996 ford ranger

my ranger will start but not shut off.i thought the cylinder lock was bad, i replaced but still doing the sane thing.

Posted by on

  • yadayada
    yadayada May 11, 2010

    DO U HAVE TILT STEERING?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

It is one of two things. The rod that connects from the tumbler or the pot metal hoop that actuates the rod and connects the tumbler to the rod. If the hoop is broken you will need to remove the steering wheel to gain access to the hoop. The hoops break in Fords all the time. They are very cheap to purchase. The steering wheel is removed first. Then the turn signal switch assembly. Then you have access to the broken hoop assembly I was telling you about. You will need a steering wheel puller to remove the steering wheel. Good luck.

Posted on Feb 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What can cause a 1996 ford ranger no to be going in gear when the vehicle start. It has a manual gear box


if you have replaced the clutch , t will be a clutch plate put in back to front
If it is hydraulic clutch ,it will be a master cylinder or slave cylinder problem
if it is cable clutch , it will be a failed clutch cable

Mar 09, 2016 | 1996 Ford Ranger SuperCab

1 Answer

Both coils do not fire on 1 and 4. Will start but only running on 2 cylinders. Could both coils be bad or should I look elsewhere?


Part 3 -How to Test the Ignition Module and Crank Sensor ...

easyautodiagnostics.com > Ford > 2.3L
Mar 1, 2012 - Spark plugs for cylinders #2 and #3 get spark at the exact same time. ...voltage -12 Volts) to both individual ignition coils within the coil pack. ... Ford Mustang or Ranger (or 2.3L Mazda B2300), this is what you'll need ... for this 'Switching Signal' at the coil pack... but you can also test this ... 1991, 1992, 1993.

How to Diagnose a Misfiring Cylinder (2.3L Ford Ranger ...

troubleshootmyvehicle.com > Ford > 2.3L
Apr 3, 2012 - Bad Fuel Injectors can cause a Misfire Condition. ... the ignition system on the 2.3L Ford Mustang or Ranger consists of 2 ignition coil packs, ...

2002 ranger misfire rough idle - Discussion on Topix

www.topix.com > Ford Ranger
Jul 27, 2007 - My truck is giving the code misfire in number 4 cyl. I replaced my spark plugs, Wires, Coil packs (both of them) and all my fuil ... three (3.0L v6) go bad, the fuel/air mixture gets messed up. Judged: 2. 2 ... My truck runs rough only at idle. ...code for ford ranger 2002, 2.3 5speed. truck runs like a champ but that ...

Extremely stumped! I need the best and brightest 1994 Ford ...

answers.edmunds.com > Edmunds Answers

Jan 31, 2016 | Cars & Trucks

1 Answer

What would a deployed airbag have to do with a no crank no start condition on a 1996 ford ranger 4.0 2wd?


The air bag issue locks out the starting system

Deployed or not the computer thinks it is.

Aug 25, 2014 | 1996 Ford Ranger SuperCab

1 Answer

Where does a evap sensor go in a 1996 ranger pickup


I'm not an expert and I have a similar problem on the 1996 Mazda extended PU w/2300 four cylinder. Same vehicle, made in ranger plant in NJ.

On the four, the purge solenoid and the purge flow sensor are located just aft (towards driver) of the battery on a vac line between the canister (next to the battery) and the intake (Just forward of the brake master cylinder.

QUESTION: Is there a pressure sensor in the fuel tank of this vehicle??????

Sep 22, 2012 | 1996 Ford Ranger SuperCab

1 Answer

My 1996 ford ranger has to be forced into 1st and 2nd gears. its a manual transmission. what would cause this?


Sounds like the clutch is going or the slave or master cylinder is failing. You could have some bad gear synchronizers.

May 02, 2010 | 1996 Ford Ranger SuperCab

1 Answer

I have a 2007 ford ranger, 6 cylinder. I drove


The oil pump may have gone bad. Involves dropping the oil pan and replacing the oil pump, check the pan for any metal peices.

Mar 06, 2010 | 2007 Ford Ranger FX4 Off-Road

5 Answers

1996 Ford Ranger won't start


I had the same problem , and if you read your book, it could be the fuel pump shut off switch, mine was bad and went from on to off position, its usually under the passenger side of the dash, look underneath at the "top" of the carpet, and you'll see a little red switch, check to see if the thing is plugged in , if it is , check to see if the switch is all the way down. i had to get a new one , sombody must have kicked mine and made it broken, but i got a new one and it worked fine

Sep 18, 2009 | 1996 Ford Ranger SuperCab

1 Answer

Wont Start


Could be the strater itself or bad connection to the starter from relay

Nov 20, 2008 | 1997 Ford Ranger SuperCab

1 Answer

Repair ignition in a 1996 Ford Taurus


You need to replace the ignition lock cylinder and/or the ignition switch actuator parts that turn the electrical switch off,on,start when the key is turned, the electrical part of the ignition is remote from the lock cylinder, it is operated by a gears and a rod.

Aug 01, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...